Search Results

During the past decades the public acceptance of the actual environmental legislation has gradually turned into an active support of the same. Test methods have anyhow become more cost heavy and time consuming, underlining the need of simplified tests with reasonable correlation to the legal methods. Generally, the emissions under static and semistatic load conditions are gradually eliminated, why the heavy pollution now comes from transient periods of the driving pattern. Consequently a transient test procedure must satisfy the quality requirements on a short test applicable to vehicles from cars to heavy trucks and busses. The INertia COLLection system described here is developed to enable low cost and well repeatable measurements of the emission characteristics of engine systems in light and heavy vehicles under transient load. The system is easy to adopt and does not need any chassis dynamometer.

The availability of the gas turbine engine for the heavy duty highway tractor application will place greater emphasis on utilizing smaller and lighter drivetrain components. This paper describes the development of components for a 10,000 rpm drivetrain from the engine to the driving wheels. The performance of the vehicle has proven the technical feasibility of a high speed drivetrain concept for gas turbine powered trucks which may eventually be commercially available.

Combustion control strategy for high efficiency and low emissions in a heavy duty (H D) diesel engine was investigated experimentally in a single cylinder test engine with a common rail fuel system, EGR (Exhaust Gas Recirculation) system, boost system and retarded intake valve closing timing actuator. For the operation loads of IMEPg (Gross Indicated Mean Effective Pressure) less than 1.1 MPa the low temperature combustion (LTC) with high rate of EGR was applied. The fuel injection modes of either single injection or multi-pulse injections, boost pressure and retarded intake valve closing timing (RIVCT) were also coupled with the engine operation condition loads for high efficiency and low emissions. A higher boost pressure played an important role in improving fuel efficiency and obtaining ultra-low soot and NOx emissions.

A multi-year Power System R&D project was initiated with the objective of developing an off-road hybrid heavy-duty concept diesel engine with front end accessory drive-integrated energy storage. This off-road hybrid engine system is expected to deliver 15-20% reduction in fuel consumption over current Tier 4 Final-based diesel engines and consists of a downsized heavy-duty diesel engine containing advanced combustion technologies, capable of elevated peak cylinder pressures and thermal efficiencies, exhaust waste heat recovery via SuperTurbo™ turbocompounding, and hybrid energy recovery through both mechanical (high speed flywheel) and electrical systems. The first year of this project focused on the definition of the hybrid elements using extensive dynamic system simulation over transient work cycles, with hybrid supervisory controls development focusing on energy recovery and transient load assist, in Caterpillar’s DYNASTY™ software environment.

The present paper reports experimental and numerical research activities devoted to deeply characterize the behavior and performance of a Heavy Duty (HD) internal combustion engine fed by compressed natural gas (CNG). Current research interest in HD engines fed by gaseous fuels with low C/H ratios is related to the well-known potential of such fuels in reducing carbon dioxide emissions, combined to extremely low particulate matter emissions too. Moreover, methane, the main CNG component, can be produced through alternative processes relying on renewable sources, or in the next future replaced by methane/H2 blends. The final goal of the presented investigations is the development of a predictive 0D combustion submodel within the framework of a 1D numerical simulation platform.

The Organic Rankine Cycle (ORC) has proven to be a promising technology for Waste Heat Recovery (WHR) systems in heavy duty diesel engine applications. However, due to the highly transient heat source, controlling the working fluid flow through the ORC system is a challenge for real time application. With advanced knowledge of the heat source dynamics, there is potential to enhance power optimization from the WHR system through predictive optimal control. This paper proposes a look-ahead control strategy to explore the potential of increased power recovery from a simulated WHR system. In the look-ahead control, the future vehicle speed is predicted utilizing road topography and V2V connectivity. The forecasted vehicle speed is utilized to predict the engine speed and torque, which facilitates estimation of the engine exhaust conditions used in the ORC control model.

A lumped-parameter thermal network model, based on the analogy between heat transfer and electric current flow, is presented for hybrid powertrain cooling systems. In order to optimally select the powertrain components that are commercially viable and meet performance, emission, fuel economy and life targets, it is necessary to consider the influence of cooling architecture. Especially in electric and hybrid vehicles, temperature monitoring is important to increase power and torque utilization while preventing thermal damages. Detailed thermal models such as FEA and CFD are considered for component level assessments as they can locate thermal hotspots and identify possible design changes needed. However, for the system level analysis, the detailed numerical models are not suitable due to the requirement of high computation effort.

In India, around 70 million people travel by public transport buses. With rising air pollution across cities, there is a need to safeguard passengers from inhaling polluted air. Contaminants in such polluted air could be fine to coarse dust (2.5 micron to 100 micron), exhaust gases (oxide of sulphur, nitrogen and carbon), total volatile organic compounds, bacteria and viruses arising out of covid-19 pandemic. Passengers commuting in buses are continuously inhaling air that is re-circulating through the Air Conditioning system (AC) and also comes in contact with multiple co-passengers and touch points. This air potentially carries a high dose of contaminants and inhalation of such air can lead to health issues. Vehicle manufacturers intend to provide clean air inside the vehicle cabin by configuring various Air Purification systems (AP) which reduce air contaminants in the closed space of a cabin.

An experimental methodology is proposed to measure the rollover propensity of road tankers when subjected to lateral perturbations derived from steering manoeuvers. The testing principle involves subjecting a scaled down sprung tank to the elimination of a lateral acceleration, to analyze its rollover propensity as a function of various vehicle's operational and design parameters. Initial acceleration is generated through putting the scaled tank on a tilt table supported by a hydraulic piston. The controlled release of the fluid in the hydraulic system generates a perturbation situation for the tank, similar to the one that a vehicle experiences when leaving a curved section of the road and going to a straight segment. Durations for the maneuver and initial tilt angles characterize both the corresponding intensities of the steering maneuver.

Harvesting is one of the most critical operations in grain production. Any means to increase the productivity and efficiency of the agricultural combine harvester has immediate benefits for the producer. This paper reports on an investigation of a control system to automatically and continuously adjust three main parameters, namely, feedrate, sieve airflow and cylinder speed. Results of field testing are presented.

Based on 3- dimensional velocity data at intake valve exit area of typical SI engine intake ports (horizontal and sloping directed ports) measured by hot wire anemometry in a steady flow rig, the magnitudes and compositions of inflow angular momentum flux and swirl ratios at the end of induction process generated by each velocity component were computed at different intake valve lifts and distances along valve axis. A microscopic evaluation method was provided for evaluating intake port characteristics according to intake valve exit flow field.

With India achieving the BSVI milestone, the diesel particulate filter (DPF) has become an imperative component of a modern diesel engine. A DPF system is a device designed to trap soot from exhaust gas of the diesel engine and demands periodic regeneration events to oxidize the accumulated soot particles. The regeneration event is triggered either based on the soot mass limit of the filter or the delta pressure across it. For a Heavy Duty Diesel Engine (HDDE), pressure difference across the DPF is not usually reliable as the size of the DPF is large enough compared to the DPF used ina passenger vehicle diesel engine. Also, the pressure difference across DPF is a function of exhaust mass flow and thus it makes it difficult to make an accurate call for active regeneration. This demands for a very accurate soot estimation model and it plays a vital role in a successful regeneration event.

An engine model for use in computer simulation of transient behavior in drivetrain and vehicle systems is presented. Two elements, important for deviation (e.g. turbo-lag) from steady state characteristics, are the inertia of the supercharging unit (turbo shaft) and the fuel injection control system. No extensive combustion calculations are carried out within the model. Instead it uses condensed results from existing combustion models and measurements. The model is semi-empirical. Some of the engine specific properties needed for simulation are (e.g. for a turbocharged diesel): engine data in steady state operation, mappings of compressor and turbine performance, inertia of the engine components condensed to the crankshaft, turbo shaft inertia, displacement, compression ratio and the essentials of the fuel injection control strategy. Input parameters to the computer program based on the model are accelerator pedal position and external torque acting on the flywheel.

The paper describes a compact low cost engine simulator used in a diagnostic system for marine diesel engines. It models normal and certain abnormal behaviour modes and can be used with an intelligent health monitor for fault recognition. The mathematical model used is the highly detailed ‘filling and emptying’ method wherein the first order equations which result from the principles of energy, mass and momentum conservation are solved on a degree by degree basis. This allows a number of faults to be simulated, for example, those which affect the airflow such as leaking intake or exhaust manifolds or fouled turbomachines or intercoolers. A multiprocessor Motorola 68020 computer system is used to allow concurrent solution of the equations for each of the thermodynamic control volumes.

An organic Rankine Bottoming cycle added to Diesel engines used for long-haul trucks has the potential of improving their peak fuel economy by up to 15% over a typical duty cycle. General Electric has developed a multi-vane rotary expander which has a measured isentropic brake efficiency of 80+% over a wide range of speed and power levels with organic working fluids. High cycle efficiency for design and off-design conditions is achieved with the multi-vane expander. The potential advantages of the multi-vane expander for the Diesel engine bottoming cycle include the elimination of a high speed gear box and the potential for over 80% isentropic engine efficiency. The multi-vane expander is a ruggedly built component running at Diesel engine speed. This paper describes the design and evaluation of a nominal 40 HP multi-vane expander for this application.

A combustion system has been developed to burn neat (pure) methanol in a direct-injection four-stroke-cycle engine. Primary objectives were to obtain low fuel consumption and long component life to make the engine suitable to replace heavy-duty diesel fueled engines. A glow plug was placed in a modified quiescent combustion chamber to ensure reliable methanol ignition at all engine operating conditions. The methanol engine provides thermal efficiency nearly equal to the diesel engine from which it is derived, in addition, nitrogen oxide emissions are reduced by 50 percent and exhaust smoke is negligible. Hydrocarbon emissions are still above the baseline diesel engine. Laboratory and field durability tests of over 2000 hours have been completed. Excellent cold-start capability has been established.

The proposed wire mesh particulate trap employs a radical design for controlling the regeneration process. A prototype for a 6.2 L diesel engine was designed, built and tested to demonstrate performance characteristics and to correlate with an analytical evaluation. Presented in this paper is the first round of test data achieved thus far. Regeneration is initiated by an electric heating element embedded in the wire mesh, and a single butterfly valve controls the division of flow between the wire mesh and bypass channels. The trap design relies on oxygen in the exhaust gases for regeneration and employs a closed-loop control logic to limit the maximum temperature during regeneration. Test results indicate an ability to achieve high collection efficiencies at low pressure drops and a controlled regeneration process. Work continues to explore the regeneration characteristics under variable engine operating conditions.

The internal combustion engines emit combustion gases which contain nano and micrometric particles that are harmful to human health, causing deleterious damages to the human's respiratory system. In Brazil, heavy vehicles, such as buses and trucks, have diesel engines that work under high loads and run through metropolitan areas or in intense traffic flow roads. They are considered, nowadays, the main solid particles emitter in several World's areas. There are already standard systems to analyze these particles quantitative and qualitatively at high prices collected from vehicle gases emissions in places such as bus stops. This paper presents a new method which retains solid micrometric particulate matter emitted by diesel engine. It is simple and has a relatively low cost. A sheet of textile element was encapsulated in a system for gripping micrometric particles emitted by diesel single-cylinder engine operating in a bench and coupled with a electrical generator.

There are several existing and emerging alternatives to lead acid batteries to provide backup energy storage for remote powering applications. These alternatives include generator sets, flywheel systems, turbine alternators, fuel cells, and superconducting magnetic energy storage (SMES). Flywheels offer dramatic improvements in performance, require little maintainance, are environmentally friendly in reliability, maintenance, lifetime, and cost over these energy storage technologies. High strength fiber composites, high efficiency electric drives, and frictionless magnetic bearings along with the declining size and cost of electronics have made these advanced flywheels.

For the purpose of developing direct injection heavy-duty methanol engines which surpass diesel engines in purformace, this paper first clarifies the methanol concentration around the spark plug for achieving a high ignition stability by sampling the gas near the spark plug using a sampling valve. The combustion process of methanol is then observed by the method of high-speed Schlieren photography to clarify the mode of methanol combustion. A new methanol DISC combustion system having a protrusion in the combustion chamber is devised based on such results. This study clarifies that the methanol concentration at the point of ignition for high ignition stability is in the range of 6 to 22 vol%. The methanol mixture burns by flame propagation so far as the compression ratio is on the order of 16.5.