Search Results

A new method for driving the hydraulic free piston engine is proposed. This method achieves the compression stroke automatically rather than special recovery system. Principle of hydraulic differential drive free-piston engine is analyzed and the control strategy of this novel hydraulic driving engine is also introduced. Then energy balance method is used to design the main parameters of the novel engine. High pressure and secondary high pressure of the hydraulic system are constrained by the combustion parameters and therefore parameters are analyzed. In order to verify the effectiveness of energy balance method, the mathematical model is established based on the piston force analysis and engine working principle. The transient results of dynamics are obtained through simulation. In addition, the effectiveness of the simulation is proofed by dimensionless analysis. It indicates that energy balance method realizes the basic performance of hydraulic free piston engine.

The Rotating Liner Engine (RLE) is an engine design concept where the cylinder liner rotates in order to reduce piston assembly friction and liner/ring wear. The reduction is achieved by the elimination of the mixed and boundary lubrication regimes that occur near TDC. Prior engines for aircraft developed during WW2 with partly rotating liners (Sleeve Valve Engines or SVE) have exhibited reduction of bore wear by factor of 10 for high BMEP operation, which supports the elimination of mixed lubrication near the TDC area via liner rotation. Our prior research on rotating liner engines experimentally proved that the boundary/mixed components near TDC are indeed eliminated, and a high friction reduction was quantified compared to a baseline engine. The added friction required to rotate the liner is hydrodynamic via a modest sliding speed, and is thus much smaller than the mixed and boundary friction that is eliminated.

The newly developed 40° hydraulic motors are an advanced bent axis piston design. The fixed and variable displacement units offer overspeed capability, high pressure ratings, high overall efficiency, and allow large external shaft loads. The variable displacement motors also feature a large displacement ratio and a wide range of controls. The paper explains the design concept and describes some typical application examples.

This study has proposed a new roll-resistant hydraulically interconnected suspension (HIS) system for a tri-axle straight truck with rear tandem axle bogie suspension to suppress the roll motion of truck body. The equations of motion of the mechanical and hydraulic coupling system are established by incorporating the hydraulic forces as external forces into the mechanical subsystem, in which the hydraulic forces are derived using impedance transfer matrix method and related to the state vectors of mechanical subsystem at the boundaries. Based on the derived equations of the coupling system, modal analysis method is employed to investigate the dynamic characteristics, including natural frequencies, mode shapes and dynamic responses. The results indicate that the proposed HIS system can effectively enhance the natural frequencies of truck body pitch and roll modes, and significantly increase the mode damping. The mode shapes of truck body are also changed.

Heavy-duty vehicles, currently the second largest source of fuel consumption and carbon emissions are projected to be fastest growing mode in transportation sector in future. There is a clear need to increase fuel efficiency and lower emissions for these engines. The Opposed-Piston Engine (OP Engine) has the potential to address this growing need. In this paper, results are presented for a 9.8L three-cylinder two-stroke OP Engine that shows the potential of achieving 55% brake thermal efficiency (BTE), while simultaneously satisfying emission targets for tail pipe emissions. The two-stroke OP Engines are inherently more cost effective due to less engine parts. The OP Engine architecture presented in this paper can meet this performance without the use of waste heat recovery systems or turbo-compounding and hence is the most cost effective technology to deliver this level of fuel efficiency.

The low and medium speed diesel engine design changes that have taken place to date and are predicted to continue for the foreseeable future, present the marine diesel lubricant with a difficult environment which is expected to become more severe with respect to both wear and cleanliness performance, on account of increasing specific power output and wider use of lower grade residual fuels. This paper describes in some detail the main in-house laboratory rig and engine techniques and procedures which have been developed by the Authors' company for assessing the important aspect of wear control; it highlights the special techniques used during shipboard testing for determining cylinder liner and piston ring wear and shows that the results from field testing correlate with those obtained from the in-house tests used to develop the latest generation of superior quality marine diesel lubricants.

The spark-assisted methanol engine has disadvantages like poor fuel economy especially at light load and low spark plug durability affected by combustion characteristics. Investigations of combustion characteristics of the spark ignition system and the autoignition system in the methanol engine and discharge characteristics of a spark plug are described in this paper. It is clear that effective autoignition was accomplished by increasing the compression ratio and adopting an EGR system in the spark-assisted methanol engine. This new improved methanol engine which is named HAMS achieved good fuel economy at light load, a low NOx emission and longer spark plug life. And a heat insulated piston with a stainless steel cap is being investigated for further improvement of autoignition combustion characteristics.

Hydraulic fluid (HF) specifications for mobile construction equipment called JCMAS HK and HKB have been established by the Fuels and Lubricants Committee of Japan Construction Mechanization Association (JCMA). The specifications are designated by two viscosity categories of single grade and multigrade. Each category has ISO viscosity grade (VG) 32 and 46. The JCMAS HK oils are recommended for use in hydraulic systems designed at pressure up to 34.3MPa(5000psi) and to heat hydraulic fluid up to 100 °C. These oils also provide wear control, friction performance, oxidation and rust protection, seal swell control and filterability performance. Two piston pump test procedures were developed to evaluate lubricating performance of these oils under high pressure conditions. The JACMAS HKB oils are classified as environmentally friendly oils due to the additional requirement for biodegradability.

Over the past decade, laser diagnostics have improved our understanding of many aspects of diesel combustion. However, interactions between the combusting fuel jet and the piston-bowl wall are not well understood. In heavy-duty diesel engines, with typical fuels, these interactions occur with the combusting vapor-phase region of the jet, which consists of a central region containing soot and other products of rich-premixed combustion, surrounded by a diffusion flame. Since previous work has shown that the OH radical is a good marker of the diffusion flame, planar laser-induced fluorescence (PLIF) imaging of OH was applied to an investigation of the diffusion flame during wall interaction. In addition, simultaneous OH PLIF and planar laser-induced incandescence (PLII) soot imaging was applied to investigate the likelihood for soot deposition on the bowl wall.

This paper reports on the development of a digital horsepower limiter for a variable volume piston pump. This is used to limit the pump's operation to a window bounded by flow and pressure limits, as well as the theoretical constant torque curve representing the prime mover's horsepower capability. A microprocessor based controller was designed, built, and tested. The digital horsepower controller continuously monitors pump flow feedback, and uses preset flow, pressure and horsepower limits. It then generates a conditioned pressure signal which is sent to an existing pressure limit control system, allowing the prime mover to be operated at its rated capacity. Testing of the digital horsepower controller indicated a stable system which maintained a constant input torque. This combined control system allows reduction in the size of the prime mover, lowering capital cost, improving efficiency, and reducing noise levels.

The fundamental drivers in the development of commercial vehicle engines are improved fuel efficiency and the need to meet more stringent exhaust emissions legislation. This strategy presents significant challenges in the development of engine components, particularly piston rings. Within the power cylinder, piston rings are significant contributors to friction losses, with the ring pack contributing up to 25 percent of the total mechanical engine friction loss, and a corresponding fuel consumption of up to four percent. The challenge lies in reducing friction power loss, without compromising oil consumption, while also mastering the increasing thermo-mechanical and tribological demands that piston rings must endure due to increased power density, smoother cylinder bores, reduced lubrication, and the use of alternative fuels.

It has been proposed that downspeeding combined with high boost levels would effectively reduce fuel consumption in heavy-duty diesel engines. Under low-speed and high-boost operating conditions, however, the in-cylinder gas pressure, which acts on the piston crown, is greater than the piston inertia force (such that there is no force reversal), over the entire range of crank angles. Therefore, the piston pin never lifts away from the main loading area (the bottom) of the connecting rod small-end bushing where the contact pressure against the piston pin is highest. In such operating conditions, lubricant starvation is easily induced at the interface between the piston pin and small-end bushing. Through carefully devised engine tests, the authors confirmed that the piston pin scuffing phenomenon arises when the boost pressure exceeds a critical value at which the no-force reversal condition appears.

The interest on improving fuel efficiency of vehicles is increasing day by day. Fuel efficiency standard for diesel commercial vehicles such as buses and trucks was published in Japan. Using a fuel efficient engine lubricant is one of the effective paths and there are several 5W-30 diesel engine lubricants in Japanese market which are advertised to give a benefit on fuel efficiency against 10W-30 oil. During the development of 5W-30 fuel efficient diesel engine oil, it was revealed that the piston underside was significantly blackened by the detergency engine test (JASO M 336: 2014). In this paper, the causative agent which blackened the piston underside was investigated and the formulation to inhibit this blackening phenomenon was studied. Through several tests, it was considered that use of poly methacrylate based viscosity index improver and ester type friction modifier deteriorated detergency performance.

Lubricating oil consumption (LOC) is a direct source of hydrocarbon and particulate emissions from internal combustion engines. LOC also inhibits the lifetime of exhaust aftertreatment system components, preventing their ability to effectively filter out other harmful emissions. Due to its influence on piston ring- bore conformability, bore distortion is arguably the most critical parameter for engine designers to consider in prevention of LOC. Bore distortion also has a significant influence on the contact forces between the piston ring and cylinder wall, which determine the wear rate of the ring and cylinder wall and can cause durability issues. Two drivers of bore distortion: thermal expansion and head bolt stresses, are routinely considered in conformability and contact analyses. Separately, bore distortion/vibration due to piston impact and combustion/cylinder pressures has been previously analyzed in wet liner engines for coolant cavitation and noise considerations.

In diesel engines, valve avoiding pit (VAP) is often designed on the top of the piston in order to avoid the interference between the valves and the piston during the engine operation. With the continued application of the downsized or high power density diesel engines, the depth of VAP has to be further deepened due to increased valve lift for more air flow into and out of the cylinder and decreased piston top clearance for less HC/CO and soot emissions. The more and more deepening of VAP changes the combustion chamber geometry, the top clearance height and the injector relative position to the piston crown. In this paper, a 3-D in-cylinder combustion model was used for a heavy duty diesel engine to investigate the effects of the depth of VAP on combustion process and emissions. Five depths of VAP were designed in this study. In order to eliminate the influence of compression ratio, the piston clearance height was adjusted for each VAP depth to keep the same compression ratio.

This paper presents analytical and measured results on the effects of injection pattern design on piston thermal management in an Opposed-Piston, Two-Stroke (OP2S) diesel engine. The OP2S architecture investigated in this work comprises two opposing pistons forming an asymmetric combustion chamber with two opposing injectors mounted on the cylinder wall. This unique configuration offers opportunities to tailor the injection pattern to control the combustion heat flux and resulting temperatures on the piston surfaces while optimizing combustion simultaneously. This study utilizes three-dimensional (3D) computational fluid dynamics (CFD) with state-of-the-art spray, turbulence and combustion models that include detailed chemistry to simulate the in-cylinder combustion and the associated flame/wall interactions. In addition, the measurements comprise a real-time thermocouple system, which allows for up to 14 locations to be monitored and recorded on the intake and exhaust pistons.

The effect of an annular, piston bowl-rim cavity on in-cylinder and engine-out soot emissions is measured in a heavy-duty, optically accessible, single-cylinder diesel engine using in-cylinder soot diagnostics and exhaust smoke emission measurements. The baseline piston configuration consists of a right-cylindrical bowl, while the cavity-piston configuration features an additional annular cavity that is located below the piston bowl-rim and connected to the main-combustion chamber through a thin annular passage, accounting for a 3% increase in the clearance volume, resulting in a reduction in geometric compression ratio (CR) from 11.22 to 10.91. Experiments using the cavity-piston configuration showed a significant reduction of engine-out smoke ranging from 20-60% over a range of engine loads.

The floating cup principle is a new axial piston concept for hydrostatic machines. It features a high number of pistons, arranged in a double ring, back-to-back configuration. Furthermore the pistons are locked onto a central rotor and each piston has its own cuplike cylinder. These ‘cups’ are floating on and supported by a barrel plate. The pistons have a ball shaped crown, which is sealing directly on the cylinder without a piston ring. A first prototype of the new pump has been built and tested. For comparison a state-of-the-art slipper type pump and a bent axis pump (both constant displacement, 28 cc/rev) have been tested as well. The steady-state performance tests have proven the high efficiency of the floating cup principle. The low speed tests, during which the pumps are tested as a motor, have confirmed the low friction losses and high starting torque of the floating cup principle. Furthermore the high number of pistons strongly reduces the torque variations.

This paper focuses on factors that enhance energy efficiency of air conditioning system on mid-sized, standard and premium buses with engine power from 125 to 280 HP. It covers aspects like light weighting of roof air conditioning system, usage of optimized ducting system with minimal resistance to blowers, deployment of rotary scroll compressor with fast idle control in place of reciprocating piston compressor. The scope of this paper covers AC compressors driven by main engine of vehicle/ bus, study related to auxiliary/donkey engine driven AC compressor is not considered. Context- In order to enhance fuel efficiency in buses an energy efficient air conditioning system should be deployed. This will lead to reduced parasitic load on the engine and translate into direct fuel saving.

The analysis of the motion of the engine piston is presented by a PC based computer program. A new CAE technique is also used to solve the engine piston problem.