Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Waste Heat Recovery from Multiple Heat Sources in a HD Truck Diesel Engine Using a Rankine Cycle - A Theoretical Evaluation

2012-09-10
2012-01-1602
Few previous publications investigate the possibility of combining multiple waste heat sources in a combustion engine waste heat recovery system. A waste heat recovery system for a HD truck diesel engine is evaluated for utilizing multiple heat sources found in a conventional HD diesel engine. In this type of engine more than 50% of heat energy goes futile. The majority of the heat energy is lost through engine exhaust and cooling devices such as EGRC (Exhaust gas recirculation cooler), CAC (Charge air cooler) and engine cooling. In this paper, the potential of usable heat recuperation from these devices using thermodynamic analysis was studied, and also an effort is made to recuperate most of the available heat energy that would otherwise be lost. A well-known way of recuperating this heat energy is by employing a Rankine cycle circuit with these devices as heat sources (single loop or dual loop), and thus this study is focused on using a Rankine cycle for the heat recovery system.
Technical Paper

Wear Characteristics of a Roller Follower Variable Valve Timing System

1995-09-01
952100
This study investigates the wear characteristics of a variable valve timing (VVT) system used to vary the phasing of the inlet valve events on a medium speed marine diesel engine. The running-in properties of critical components within the system are examined. The effect of surface finish and surface hardness upon wear is examined. It was found that in order to prevent excessive wear between the roller and tappet follower then the roller should be harder than the tappet. Tappet and roller hardness values of 60 and 70 Rockwell Hardness ‘C’ (HRC) respectively were found to be satisfactory.
Technical Paper

Wear Study of Coated Heavy Duty Exhaust Valve Systems in a Experimental Test Rig

2012-04-16
2012-01-0546
The exhaust valve system of combustion engines experiences a very complex contact situation of frequent impact involving micro sliding, high and varying temperatures, complex exhaust gas chemistry and possible particulates. The wear rate has to be extremely low, and the individual wearing events operate at a scale that is very demanding to detect. The tribological conditions in the exhaust valve system are expected to become even worse for engines that will follow the future emission regulations. The regulations demand reduced amounts of soot and particles, sulfur compounds, etc., which today act beneficial for the seating surfaces. The reductions are expected to increase the metal-to-metal contact.
Technical Paper

Wear Trends of Axial Piston Type Pumps Operating in Severe Environments

1989-09-01
891868
Axial piston type pumps are often exposed to severe operating conditions because of the duty cycle, the environment, or, in some situations, poor maintenance and even abuse. The detrimental effects on the pump and the hydraulic system as a result of these adverse conditions are often not known or predictable. In this study, four controlled severe operating conditions were imposed on four identical axial piston type pumps. They included 1) constant high load pressure and normal fluid temperature, 2) constant high load pressure and elevated fluid temperature, 3) cyclic load pressure and normal fluid temperature, and 4) cyclic load pressure and elevated fluid temperature. The tests were long-term; they were run continuously for up to 5000 hours. The pump wear was monitored in all cases using ferrography. In addition, the condition of the fluid was monitored and the circuit filters were examined periodically. The results of the findings are presented in this paper.
Technical Paper

Wear of Bearing Materials

1994-04-01
941111
Wear characteristics of four bearing materials have been investigated under different sliding conditions. The bearing materials used were CDA 954, CDA 863, CDA 932, and CDA 938. Using a Taber Wear Tester, a cylinder on a flat geometry was used as a tribo contact pair. All bearing materials in the form of a thick cylindrical disk were subjected to combined sliding-rolling motion against a rotating flat disk. The flat disk was either an abrasive disk, or a very soft steel disk, or a hardened steel disk with and without lubrication. Wear was measured as weight loss after several thousand cycles of rotation. Maximum wear of the bearing materials occurred when the counter body was a very soft steel disk. These results together with the wear rate of each bearing material sliding against four different counter bodies are presented. These results are found to be of practical importance in the design and application of journal bearings made of materials used in this investigation.
Technical Paper

Well-to Wheel Greenhouse Gas Emissions of LNG Used as a Fuel for Long Haul Trucks in a European Scenario

2013-09-08
2013-24-0110
The EU Commission's “Clean Power for Transport” initiative aims to break the EU's dependence on imported oil whilst promoting the use of alternative fuels to reduce greenhouse gas emissions. Among the options considered is the use of liquefied natural gas (LNG) as a substitute for diesel in long haul trucks. It is interesting to ask how the lifecycle greenhouse gas (GHG) emissions of LNG compare with conventional diesel fuel for this application. The LNG available in Europe is mainly imported. This paper considers the “well-to-tank” emissions of LNG from various production routes, including: gas production, treatment and liquefaction, shipping to Europe, terminal, distribution and refuelling operations. “Tank-to-Wheel” emissions are considered for a range of currently-available engine technologies of varying efficiency relative to diesel.
Technical Paper

Why Not 125 BMEP in an L-Head Truck Engine?

1939-01-01
390130
HIGH output per cubic inch of piston displacement is desirable not alone for the purpose of being able to transport more payload faster, but more particularly for the invariably associated byproduct of lower specific fuel consumption, and especially at road-load requirements. The only way of accomplishing this purpose is through the use of higher compression ratios, and the limiting factors for this objective are fuel distribution and the operating temperatures of the component parts. A manifold is proposed which not only definitely improves distribution at both full and road loads, but has the inherent additional advantage of reducing the formation of condensate, thus still further facilitating a reduction in road-load specific fuel consumption. Hydraulic valve lifters, obviation of mechanical and thermal distortion, and controlled water flow are the essentials in improved cooling.
Technical Paper

Why Not Convert to Ductile Iron?

2002-03-19
2002-01-1451
Cast iron is generally thought of as a weak, dirty, cheap, brittle material that does not have a place in applications requiring high strength and defined engineering properties. While gray cast iron is relatively brittle by comparison with steel, ductile iron is not. In fact, ductile iron has strengths and toughness very similar to steel and the machinability advantages make an attractive opportunity for significant cost reductions. Gray and ductile iron bar stock is commercially available and can be used as a direct replacement in applications that are currently being made from carbon steel bar. Ductile iron bar stock conversions are very prevalent in many fluid power applications including glands and rod guides, cylinders, hydrostatic transmission barrels and in high-pressure manifolds. Automotive gears are being converted to ductile iron for its damping capacity and cost reductions.
Technical Paper

Why Not a New Engine ?

1980-11-01
801428
Leading contenders in the search for a superior alternative powerplant for light-duty automotive use include the steam and Stirling engines, the gas turbine, and the diesel. In this paper the status of each of those alternative engines is reviewed and i its prognosis considered. The steam engine is unsuitable because of poor fuel economy. Obstacles blocking acceptance of the Stirling and gas turbine engines are sufficient so that even if they are surmountable, significant-use in light-duty vehicles is unlikely before the 1990s. The light-duty diesel is here today but faces some difficult regulatory hurdles in the near future.
Technical Paper

Wind Tunnel Investigation of the Effects of Installation Parameters on Truck Cooling System Performance

1976-02-01
760832
The effect of eight installation and component parameters on cooling system heat rejection and air flow were examined in detail in a wind tunnel facility. A quarter-replicate, two level factorial test plan was followed. Within the ranges of each parameter tested, the fan characteristics and the projection of fan into the shroud are highly significant parameters. The fan to radiator distance, the radiator characteristics, and the fan tip to shroud clearance are significant parameters. The fan to engine block distance and the type of shroud are not significant parameters.
Standard

Windshield Defrosting Systems Test Procedure and Performance Requirements—Trucks, Buses, and Multipurpose Vehicles

2000-09-29
HISTORICAL
J381_200009
This SAE Recommended Practice establishes uniform test procedures and performance requirements for the defrosting system of enclosed cab trucks, buses, and multipurpose vehicles. It is limited to a test that can be conducted on uniform test equipment in commercially available laboratory facilities. Current engineering practice prescribes that for laboratory evaluation of defroster systems, an ice coating of known thickness be applied to the windshield and left- and right-hand side windows to provide more uniform and repeatable test results, even though under actual conditions such a coating would necessarily be scraped off before driving. The test condition, therefore, represents a more severe condition than the actual condition, where the defroster system must merely be capable of maintaining a cleared viewing area.
Technical Paper

Wire Braid Angle Response Characteristics in Hydraulic Hose

1997-09-08
972706
This report is concerned with the effects of braid angle on the behavior of hydraulic hose. For equilibrium conditions to exist, and if the braid layers are assumed to bear tension forces only, the angle of the reinforcement layers must be along that of the total force exerted by the internal pressure. This is the neutral angle θN, which has a theoretical value of 54.74° (54°44′). It is possible to hypothesize a fretting wear model in which wires move on top of one another inside a braid layer if the braid angle is different from this theoretical neutral angle. Even though theoretical claims are made by some technical professionals, the hydraulic hose industry has been successfully making hoses with non-neutral braid angles for years. Testing and application have shown that fretting wear is not a principal cause of hose failure and fatigue.
Standard

Wireless Power Transfer for Heavy-Duty Electric Vehicles

2024-05-29
WIP
J2954/2
The published SAE J2954 standard established an industry-wide specification that defines acceptable criteria for interoperability, electromagnetic compatibility, EMF, minimum performance, safety, and testing for wireless power transfer (WPT) for light duty plug-in electric vehicles. This SAE Information Report, SAE J2954/2, defines new power transfer levels in the higher power ranges needed for heavy-duty electric vehicles. This Recommended Practice document addresses the requirements based on these charge levels and different vehicle applications as a first step in the process of completing a standard that the industry can use, both for private (fleet) and public wireless power transfer, including for charging electric vehicle batteries. This revision focusses exclusively on static HD-WPT. A new document, has been created, SAE RP J2954/3 that will encompass all dynamic wireless power transfer (D-WPT).
Standard

Wireless Power Transfer for Heavy-Duty Electric Vehicles

2022-12-16
CURRENT
J2954/2_202212
The published SAE J2954 standard established an industry-wide specification that defines acceptable criteria for interoperability, electromagnetic compatibility, EMF, minimum performance, safety, and testing for wireless power transfer (WPT) for light-duty plug-in electric vehicles. This SAE Information Report, SAE J2954/2, defines new power transfer levels in the higher power ranges needed for heavy-duty electric vehicles. This document addresses the requirements based on these charge levels and different vehicle applications as a first step in the process of completing a standard that the industry can use, both for private (fleet) and public wireless power transfer, including for charging electric vehicle batteries. This document is the first step in a process towards HD static and dynamic WPT. This document lacks specific requirements and solutions, for which field data is needed.
Event

Workshops - Program - 2025 Government Industry Meeting

2024-10-13
Annual conference government policy, regulatory makers, automotive industry neutral forum discuss US government regulation, technology, customer acceptance future vehicle design. industry event safety, emission control, fuel efficiency, automated vehicles.
Technical Paper

ZF Retarder in Commercial Vehicles

1992-11-01
922452
This paper describes the ZF - Intarder, a wear-free vehicle brake for commercial vehicles. Qualities such as optimum weight saving, compactness, compatibility with all PTOs and no change in driveshaft length, are the results of a new development. Performance measurements demonstrate connection with engine cooling system. Field test measurements provide new information about frequency of use of various brake levels and electronic speed control. An evaluation of financial issues indicates advantages for operation.
Technical Paper

a progress report — Dry-Type Air Cleaners on Farm Tractors

1959-01-01
590026
GREATER ease of servicing is one of the ultimate goals in the development of dry-type air cleaners. The authors acknowledge, however, that the oil-bath cleaner is a rugged proved component that has done a good job for the farmers who serviced it properly. This paper describes studies made in Illinois of oil-bath and dry air cleaners in field service. At the same fuel/air ratios, the maximum horsepower of a test engine was greater with the dry-type filter than with the oil-bath cleaner. It was found that with AC fine dust and steady airflow, the oil-bath cleaners had significantly lower efficiencies than the dry-type filter. At less than rated airflow the efficiency of the oil-bath cleaner decreased while that of the dry filter remained high.
Technical Paper

“Build Your Hybrid” - A Novel Approach to Test Various Hybrid Powertrain Concepts

2023-04-11
2023-01-0546
Powertrain electrification is becoming increasingly common in the transportation sector to address the challenges of global warming and deteriorating air quality. This paper introduces a novel “Build Your Hybrid” approach to experience and test various hybrid powertrain concepts. This approach is applied to the light commercial vehicles (LCV) segment due to the attractive combination of a Diesel engine and a partly electrified powertrain. For this purpose, a demonstrator vehicle has been set up with a flexible P02 hybrid topology and a prototype Hybrid Control Unit (HCU). Based on user input, the HCU software modifies the control functions and simulation models to emulate different sub-topologies and levels of hybridization in the demonstrator vehicle. Three powertrain concepts are considered for LCVs: HV P2, 48V P2 and 48V P0 hybrid. Dedicated hybrid control strategies are developed to take full advantage of the synergies of the electrical system and reduce CO2 and NOx emissions.
X