Search Results

THE X-ray spectrum readily adapts itself to problems in chemical analysis and crystal formation. It is effective on very minute particles which otherwise cannot be segregated. A permanent record is made, and the specimens may be used over and over again, as the X-ray is non-destructive. As a means of inspection, X-ray clearly shows the interior of objects such as weldings castings, forgings, cold-worked metals, and so on. Inhomogeneities that are very slight in width and a fraction of one per cent in thickness are seen easily on a radiograph. Defects thus found may be eliminated summarily by checking various steps in production.

Cavitation plays a significant role in high pressure diesel injectors. However, cavitation is difficult to measure under realistic conditions. X-ray phase contrast imaging has been used in the past to study the internal geometry of fuel injectors and the structure of diesel sprays. In this paper we extend the technique to make in-situ measurements of cavitation inside unmodified diesel injectors at pressures of up to 1200 bar through the steel nozzle wall. A cerium contrast agent was added to a diesel surrogate, and the changes in x-ray intensity caused by changes in the fluid density due to cavitation were measured. Without the need to modify the injector for optical access, realistic injection and ambient pressures can be obtained and the effects of realistic nozzle geometries can be investigated. A range of single and multi-hole injectors were studied, both sharp-edged and hydro-ground. Cavitation was observed to increase with higher rail pressures.

The development of the XB-70 research aircraft produced advancements in many fields of technology. This paper covers a few of these advancements in the areas of materials, equipment, and manufacturing. These include honeycomb construction, PH 15-7 alloy steel, vacuum melted H-11 steel, equipment capable of withstanding high temperatures, chemical milling of many different alloys, miniaturized welding equipment, and exothermic brazing techniques.

Automotive clearcoats have many purposes, from providing a glossy finish to protecting the underlying paint layers from UV radiation. Yellowing of clearcoats is a natural phenomenon during weathering processes, as well as from extreme baking conditions, due to polymer degradation. However, occasionally yellowing may be caused by unexpected chemical reactions occurring in the clearcoat. These reactions may happen very quickly (within hours or days) or take years to manifest, as other chemicals migrate into the clearcoat. We have investigated one family of these unexpected reactions which occur with certain UV absorbers, as well as how to prevent the reactions from occurring. We found that certain benzotriazole UV absorbers react readily with some common metals, including copper and zinc, provided that the UV absorber is not in its excited state. The conformational change that occurs within the benzotriazole when it absorbs UV radiation effectively inhibits the reaction with metals.

Under certain conditions, metals and other solids deform plastically. There are two conditions which promote plastic deformation: the condition of stress and the mechanism which determines how that deformation takes place. The critical condition of stress which produces yielding is due to the net effect of the combination of stresses acting at a point. A mathematical theory which predicts the critical condition of stress for which plastic flow occurs is a yield criterion. A new yield criterion is introduced. It is hyperbolic in form so it is significantly different from the criteria developed by Rankine, Tresca, Saint-Venant, or von Mises. But like these criteria, the new yield condition is also limited to a biaxial stress condition. The new yield criterion, because of its form, serves as an instructive model for the development of an analytical equation of equivalent form.

The hazardous bulk chemical liquid cargo transportation is usually made through highways, using special automotive devices, named semitrailer tank, a kind of mobile tank specially developed to perform this task, manufactured with many types of steel, selected according to the chemical characteristics of the product to be transported. Equipment sizing is made based on specific standards which include specified formulas, loading, and safety factors representing the design criteria of this type of device. Despite of the detailed design criteria for semitrailer tank, it has been observed failure of some pieces of equipment during operation, in a shorter effective life than that one considered in the design phase itself. Considering a detailed study of the stress distribution in this type of equipment, this paper shows a verification of the possibility of yielding failure in the semitrailer tank structure.

This specification covers a zinc alloy in the form of die castings.

This specification covers a zinc alloy in the form of die castings.

SIMILAR SPECIFICATIONS—UNS Z33521, former SAE 903, ingot is similar to ASTM B 240-79, Alloy AG40A; and UNS Z33520, former SAE 903, die casting is similar to ASTM B 86-76, Alloy AG40A. UNS Z35530, former SAE 925, ingot is similar to ASTM B 240-79, Alloy AC41A; and UNS Z35531, former SAE 925, die casting is similar to ASTM B 86-82a, Alloy AC41A.

Because of the drastic chilling involved in die casting and the fact that the solid solubilities of both aluminum and copper in zinc change with temperature, these alloys are subject to some aging changes, one of which is a dimensional change. Both of the alloys undergo a slight shrinkage after casting, which at room temperature is about two-thirds complete in five weeks. It is possible to accelerate this shrinkage by a stabilizing anneal, after which no further changes occur. The recommended stabilizing anneal is 3 to 6 h at 100 °C (212 °F), or 5 to 10 h at 85 °C (185 °F), or 10 to 20 h at 70 °C (158 °F). The time in each case is measured from the time at which the castings reach the annealing temperature. The parts may be air cooled after annealing. Such a treatment will cause a shrinkage (0.0004 in per in) of about two-thirds of the total, and the remaining shrinkage will occur at room temperature during the subsequent few weeks.

This specification covers the engineering requirements for electrodepositton of zinc and the properties of the deposit.