Search Results

Advanced high-strength steels (AHSS) are a class of steels that have a minimum tensile strength of 500 MPa. The advantages of AHSS include superior formability and better crash energy absorption compared with conventional low-strength steels having a minimum tensile strength of 270 MPa. Several steels with a minimum tensile strength of 590 MPa have already found use in current vehicles, and others with minimum tensile strength up to 980 MPa have been qualified for use in future vehicle models. Two 780 MPa steels of interest are 780 DP (Dual Phase) and 780 TRIP (TRansformation Induced Plasticity). In this study, an examination was undertaken to compare the resistance spot-welding behavior of commercially produced 1.6 mm-thick, hot-dipped galvannealed, 780 MPa DP and TRIP steel sheet. Included in the study were evaluations of the weld lobes, weld microhardness, and the shear- and cross-tension strengths of resistance spot welds for the two steels.

The high temperature fatigue behaviors of three cast aluminum alloys used for cylinder head fabrication - 319, A356 and AS7GU - are compared under isothermal fatigue at room temperature and elevated temperatures. The thermo-mechanical fatigue behavior for both out-of-phase and in-phase loading conditions (100-300°C) has also been investigated. It has been observed that all three of these alloys present a very similar behavior under both isothermal and thermo-mechanical low-cycle fatigue. Under high-cycle fatigue, however, the alloys A356 and AS7GU exhibit superior performance.

The Magnesium Front End Research and Development (MFERD) project under the sponsorship of Canada, China, and USA aims to develop key technologies and a knowledge base for increased use of magnesium in automobiles. The primary goal of this life cycle assessment (LCA) study is to compare the energy and potential environmental impacts of advanced magnesium based front end parts of a North American-built 2007 GM-Cadillac CTS using the current steel structure as a baseline. An aluminium front end is also considered as an alternate light structure scenario. A “cradle-to-grave” LCA is conducted by including primary material production, semi-fabrication production, autoparts manufacturing and assembly, transportation, use phase, and end-of-life processing of autoparts. This LCA study was done in compliance with international standards ISO 14040:2006 [1] and ISO 14044:2006 [2].

The quality of the nitrocarburized layer has a decisive influence in the service life of components with pistons that work together with polymeric seals, since it interferes in the abrasion and wear mechanisms of the involved materials. Thus it is necessary to select the most adequate process to apply in a given component aiming for a quality improvement and warranty costs reduction. The literature offers a great volume of information about the different nitriding processes, but there are few reports comparing them. In this paper the salt bath and plasma processes are discussed concerning the white layer metallography, roughness and the process effect on corrosion resistance of gas spring rods manufactured with SAE 1040 steel.

Engine mounts are an integral part of the vehicle that helps in reducing the vibrations generated from the engine. Engine mounts require a simple yet complicated amalgamation of two very different materials, steel and rubber. Proper adhesion between the two is required to prevent any part failure. Therefore, it becomes important that a comprehensive study is done to understand the mating phenomenon of both. A good linking between rubber and metal substrate is governed by surface pretreatment. Various methodologies such as mechanical and chemical are adopted for the same. This paper aims to present a comparative study as to which surface pretreatment has an edge over other techniques in terms of separation force required to break the bonding between the two parts. The study also presents a cost comparison between the techniques so that the best possible technique can be put to use in the commercial vehicle industry.

Automotive friction materials are composites containing three kinds of components: an organic binder, fiber for reinforcement, and property modifiers. At low braking temperatures, the wear rate of the friction materials is controlled primarily by abrasive and adhesive mechanisms. At higher braking temperatures, the wear rate increases exponentially with increasing temperature due to thermal degradation of the binder and other components, and the exponential wear rate is frequently accompanied by brake fade. Thus, one method of reducing thermal wear and fade tendency is to lower the temperature at the rotor/friction material interface. Since the rate of heat transfer from the interface is mostly dependent upon the conductive and convective modes, a rotor of high thermal conductivity will have a significant advantage over a rotor of low conductivity, if the heat capacity remains the same.

This study investigates occupant containment characteristics of tempered and laminated automotive moveable side glass in rollover collisions. FMVSS 216 test protocols were used to induce roof damage or sheet metal damage around the window opening in Lincoln Navigators equipped with tempered and laminated side glass. Dummy-drop tests were then performed to investigate relative containment. The results demonstrate that, for rollovers in which the window structure is compromised, tempered side glass and laminated side glass perform comparably relative to occupant containment. Also discussed are the general strength characteristics of different types of glass construction, the availability of laminated side glass in recent model U.S. vehicles, and anecdotal data supporting the conclusions of testing.

Weight reduction is a primary concern in the design of today's automobiles. Fiber reinforced composites (FRC) comprise a category of materials that may offer advantages in terms of weight and cost when compared to both steel and aluminum. The viability of low cost FRCs such as a glass fiber reinforced plastic (GFRP) as a structural material for automotive applications can, however, be diminished by functional requirements such as energy absorption and crush under impact loading. In this context, the crash safety performance of front rails of a compact passenger car is evaluated by assuming these to be made of GFRPs with constant strand mat (CSM) plies. The safety assessment of rails is carried out with the aid of the explicit nonlinear finite element analysis code LS-DYNA with utmost attention being paid to the proper constitutive modeling of the composites considered.

Dent resistance is an important attribute in the automotive panel design, and the ability to accurately predict a panel's dentability requires careful considerations of sheet metal properties, including property changes from stamping process. The material is often work-hardened significantly during forming, and its thickness is reduced somewhat. With increased demand for weight reduction, vehicle designers are seriously pushing to use thinner-gauged advanced high-strength steels (AHSS) as outer body panels such as fenders, hoods and decklids, with the expectation that its higher strength will offset reduced thickness in its dentability. A comparative study is conducted in this paper for a BH210 steel fender as baseline design and thinner DP500 steel as the new design.

This study investigates and compares fatigue behavior of forged steel and powder metal connecting rods. The experiments included strain-controlled specimen testing, with specimens obtained from the connecting rods, as well as load-controlled connecting rod bench testing. Monotonic and cyclic deformation behaviors, as well as strain-controlled fatigue properties of the two materials are evaluated and compared. Experimental S-N curves of the two connecting rods from the bench tests obtained under R = -1.25 constant amplitude loading conditions are also evaluated and compared. Fatigue properties obtained from specimen testing are then used in life predictions of the connecting rods, using the S-N approach. The predicted lives are compared with bench test results and include the effects of stress concentration, surface finish, and mean stress. The stress concentration factors were obtained from FEA, and the modified Goodman equation was used to account for the mean stress effect.

A drag dynamometer was used to evaluate the performance of automotive brake drums made from four kinds of materials with different thermal conductivities. In the order of decreasing thermal conductivity they are chromium copper, aluminum/cast iron composite, cast iron, and nickel-aluminum bronze. All of the drums were of the standard configuration used in SAE J 661a, or closely approximated it. The drums were run in conjunction with three types of lining materials: nonabrasive, moderately abrasive, and highly abrasive. Temperatures near the lining/drum interface, coefficients of friction, and lining wear were measured and compared. For a given amount of work done, the temperature near the drum surface was found to be lowest for the chromium copper drums, with progressively higher temperatures in the aluminum/cast iron composite, nickel-aluminum bronze, and cast iron drums. Relative lining wear and coefficient of friction varied with the type of lining tested.

Internal short-circuit in cells/batteries is a phenomenon where there is direct electrical contact between the positive and negative electrodes leading to thermal runaway. The nail penetration tests were used to simulate an internal short circuit within the battery, where a conductive nail was used to pierce the battery cell separator membrane which provided direct electrical contact between the positive and negative electrodes. The batteries tested during this work were common batteries used in existing automotive applications, and they included a nickel manganese cobalt (NMC) battery from a Chevrolet Bolt, a lithium manganese oxide (LMO) battery from a Chevrolet Volt, and a lithium iron phosphate (LFP) battery in a hybrid transit bus. The battery abuse and emissions tests were designed to intentionally drive the three different battery chemistries into thermal runaway while measuring battery temperatures, battery voltages and gaseous emissions.

Internal short-circuit in cells/batteries is a phenomenon where there is direct electrical contact between the positive and negative electrodes leading to thermal runaway. The nail penetration tests were used to simulate an internal short circuit within the battery, where a conductive nail was used to pierce the battery cell separator membrane which provided direct electrical contact between the positive and negative electrodes. The batteries tested during this work were common batteries used in existing automotive applications, and they included a nickel manganese cobalt (NMC) battery from a Chevrolet Bolt, a lithium manganese oxide (LMO) battery from a Chevrolet Volt, and a lithium iron phosphate (LFP) battery in a hybrid transit bus. The battery abuse and emissions tests were designed to intentionally drive the three different battery chemistries into thermal runaway while measuring battery temperatures, battery voltages and gaseous emissions.

Recently several new magnesium alloys for high temperature applications have been developed with the aim to obtain an optimal combination of die castability, creep resistance, mechanical properties, corrosion performance and affordable cost. Unfortunately, it is very difficult to achieve an adequate combination of properties and in fact, most of the new alloys can only partially meet the required performance and cost. This paper aims at evaluating the current status of the newly developed alloys for powertrain applications. The paper also addresses the complexity of magnesium alloy development and illustrates the effect of alloying elements on properties and cost. In addition, the paper presents an attempt to set the position of each alloy in the integrated space of combined properties and cost

Non-Asbestos Organic (NAO) disc pads and Low Steel Lomet disc pads were subjected to high and low humidity conditions to discover how humidity affects these two classes of formulations for physical properties, friction, wear and noise characteristics. The 2 classes of formulations show similarities and differences in response to increasing humidity. The humidity effect on deformation of the surface microstructure of the gray cast iron disc is also investigated. Humidity implications for pad quality control and brake testing are discussed.

To advance vehicle lightweighting, chopped carbon fiber sheet molding compound (SMC) is identified as a promising material to replace metals. However, there are no effective tools and methods to predict the mechanical property of the chopped carbon fiber SMC due to the high complexity in microstructure features and the anisotropic properties. In this paper, a Representative Volume Element (RVE) approach is used to model the SMC microstructure. Two modeling methods, the Voronoi diagram-based method and the chip packing method, are developed to populate the RVE. The elastic moduli of the RVE are calculated and the two methods are compared with experimental tensile test conduct using Digital Image Correlation (DIC). Furthermore, the advantages and shortcomings of these two methods are discussed in terms of the required input information and the convenience of use in the integrated processing-microstructure-property analysis.

The cyclic behavior of single overlap aluminum joints joined through a number of different methods has been investigated using Alcan 5754-O, an alloy that potentially could be used in structural applications. Overlap shear tests of spot welded, clinched and riveted joints are compared on the basis of their fatigue performance. The fatigue response of the spot welded joint was the baseline to which the other fasteners were compared. Test results showed an improvement of approximately 25% for both the mechanical clinch joints and aluminum rivets in fatigue strength at 106 cycles. The most significant improvement in fatigue strength of 100% was found for the self piercing rivets at 106 cycles. The failure behavior of the various joining methods is discussed as well as the surface appearance.

In automotive body manufacturing the dies for blanking/trimming/piercing are under most severe loading condition involving high contact stress at high impact loading and large number of cycles. With continuous increase in sheet metal strength, the trim die service life becomes a great concern for industries. In this study, competing trim die manufacturing routes were compared, including die raw materials produced by hot-working (wrought) vs. casting, edge-welding (as repaired condition) vs. bulk base metals (representing new tools), and the heat treatment method by induction hardening vs. furnace through-heating. CaldieTM, a Uddeholm trademarked grade was used as trim die material. The mechanical tests are performed using a WSU developed trimming simulator, with fatigue loading applied at cubic die specimen’s cutting edges through a tungsten carbide rod to accelerate the trim edge damage. The tests are periodically interrupted at specified cycles for measurement of die edge damage.

Nickel based superalloys have a wide range of applications due to high mechanical strength at high temperatures, fracture toughness and resistance to corrosion. However, because of their outstanding properties, it is considered as the difficult to machine materials. Inconel alloy X-750 is used extensively in rocket-engine thrust chambers. Airframe applications include thrust reversers and hot-air ducting systems along with large pressure vessels are formed from Inconel alloy X-750. Moreover, the comparative analysis of machinability aspect using coated carbide inserts is reported few. The current study explains the machinability investigation on Inconel alloy X-750 superalloys using coated carbides. To collect the experimental data, the L16 experimental design plan is used to experiment with a machining length of 40 mm.

This paper describes an investigation on microstructures as well as mechanical properties of pure aluminium graphene nano platelets (GNPs) metal matrix composites prepared via novel based stir casting technique combined with ultrasonic treatment. The proportion of graphene changes from 0.5 to 2.0 wt. % in aluminium with 99% purity. The investigations on composites revealed that Al with combination of 1.0 % graphene composite showcased enhanced mechanical properties with 48.49 % (~49%) increase in tensile strength and 34.53 % (~35%) increase in micro hardness compared to test results of composites produced by traditional stir casting technique. FESEM analysis was done to examine the surface morphology of produced composite and fracture surface of tested composites where as XRD analysis was to inspect the phase analysis of produced composites.