Search Results

The general method of procedure taken by the Air Service before beginning the actual design and construction of the necessary types of aircraft engine is outlined and the four steps of the development subsequent to a very complete study of existing domestic and foreign engines are stated. After checking over the layouts, if all the details are agreed upon by both the designer and the Engineering Division, the contract is placed, usually for two experimental engines, and the construction work is begun. Acceptance tests are made to demonstrate that the engine is capable of running at normal speed and firing on all cylinders. These are followed by the standard performance test made on the dynamometer at McCook Field. The results of the latter test determine whether the engine can enter the 50-hr. endurance test. The engine is then torn-down and inspected for wear. Suggested modifications are embodied in reconstructed engines which eventually fulfill the requirements.

The development of intake-manifolds in the past has been confined mainly to modifications of constructional details. Believing that the increased use of automotive equipment will lead to a demand for fuel that will result in the higher cost and lower quality of the fuel, and being convinced that the sole requirement of satisfactory operation with kerosene and mixtures of the heavier oils with alcohol and benzol is the proper preparation of the fuel in the manifold, the authors have investigated the various methods of heat application in the endeavor to produce the minimum temperature necessary for a dry mixture. Finding that this minimum temperature varied with the method of application of the heat, an analysis was made of the available methods on a functional rather than a structural basis.

The author gives a brief and purely qualitative treatment of what a vapor is, where it comes from and how it appears; the necessity of vaporizing a liquid fuel before attempting to burn it; the separate effects of the conditions that control vaporization; and the heat-balance of vaporization. This is done to summarize the conditions surrounding and controlling fuel vaporization in the cycle of operation of a throttle-controlled internal-combustion engine, fitted with an intake-manifold and a carbureter. Charts and photographs are included and commented upon, descriptions being given of actual demonstrations that were made at the time the paper was presented. The conclusion is reached that it is well to depend as little as possible upon the cylinder heat and temperature to complete the vaporization of the fuel.

The object of the paper is to consider some of the fundamental factors that affect oil consumption; it does not dwell upon the differences between lubricating systems. Beyond the fact that different oils apparently affect the oil consumption and that there is a definite relation between viscosity and oil consumption, the effect of the physical characteristics, or the quality of the oil, does not receive particular attention. The methods of testing are described and the subject is divided into (a) the controlling influence of the pistons, rings and cylinders; (b) the controlling influence of the source from which the oil is delivered to the cylinder wall.

Oil-pumping is defined and its results are mentioned. The influence of various operating conditions is brought out, particular reference being made to passenger-car service. The factors that control the rate of oil consumption are described in detail and some unusual conditions are reported. Various features of piston grooving and piston-ring design are mentioned and the effect of changes illustrated. The relative advantages of the splash and the force-feed systems as affecting the development of oil-pumping troubles are set forth and improvements suggested. A new device for reducing oil-pumping dilution troubles is described and illustrated.

The gradual trend toward overhead valves in automobile engines, as indicated by an increase in their use on American cars from 6 per cent in 1914 to 31 per cent in 1922, has been accelerated, in the opinion of the author, by their successful application to aircraft engines and by the publicity given them by their almost universal adoption on racing machines. Tractor engines recently brought out show the advantage of this construction.

The lightness and high thermal conductivity of aluminum pistons are conceded and the paper deals principally with their thermal properties, inclusive of the actual operating temperature of the pistons, the temperature distributions in the piston and the effects of the cooling-water temperature and the piston material on the piston temperature. The apparatus is illustrated and described, and charts are presented and commented upon in connection with a discussion of the results obtained. Theories affecting piston design are presented and discussed, reference being made to diagrams relating to design procedure: The work is supplementary to that done in 1921 by the authors, which they presented in a similar paper to which they refer.

The authors present and discuss the results obtained from combined road and laboratory tests made to determine the amount of power required to maintain a given car speed. The specifications of the car and its engine are stated and the variable-ratio rocker-arm of the engine is illustrated and its advantages explained, together with those of the valve-timing. The subject of manifold gas-velocity is treated in some detail, inclusive of a diagram showing the hot-spot or vaporizing device that was used. The test data are reduced to curve form, eight charts being shown. The curves include those for brake horsepower, indicated horsepower, comparative performance, performance at different throttle-openings and at different loads, fuel consumption and indicated thermal efficiencies.

After pointing out that the general question of weight reduction is no exception to the fallacies that seem to have beset the development of the automobile from its earliest days, the author outlines briefly the problem confronting the automobile designer. The influence of the weight of the reciprocating parts on the chassis in general and the engine in particular is emphasized as being of greater importance than the actual saving in the weight of the parts themselves, it being brought out that the bearing loading due to inertia is really the factor that limits the maximum engine speed. Reference is made to the mathematical investigation by Lanchester in 1907 of the advantages of using materials of high specific-strength and the conclusions arrived at are quoted in full. A tabulation of the specific strengths of various materials used in automotive engineering practice is presented as showing the advantages of aluminum as compared with steel.

Metropolitan-New England Sections Paper - The loss of power due to the friction of the various parts of the chassis has been carefully and elaborately investigated by a dynamometer, the dual purpose being the determination of the amount of internal frictional resistance of the front or rear wheels and the measurement of the power that can be delivered at the rear wheels with the concomitant rate of fuel consumption. The rolling-friction due to the resistance of the wheels as a whole is taken up first and afterward the separate resistances of the tires, bearings and transmission are studied under varying conditions of inflation-pressure and load. The five frictional resistances that were chosen as giving the most useful information are those of the front tires, the rear tires, the front bearings, the rear bearings and the engine.

Stating that the trend of tractor development must be toward the small tractor that is capable of handling all of the power work on a farm, the author quotes farm and crop-acreage statistics and outlines diversified farming requirements, inclusive of row-crop cultivation. Tractor requirements are stated to be for a sturdy compact design to meet the demands of the diversified farm, which include plowing, seeding, cultivating, hauling and belt-power usage, and these requirements are commented upon in general terms. Consideration is given to farm implements in connection with tractor operation, and the placing of cultivating implements ahead of the tractor is advocated.

The authors enumerate some of the questions that are involved and, after outlining a previous paper on the subject of plows, analyze these questions in part by the aid of diagrams and applied mathematics. Comparative draft data are presented in tabular form and commented upon, as well as comparative hitch-length data. Tractor reactions are explained and discussed in some detail in a similar manner, special attention being given to the reactions on a slope and up-hill. The reactions on cross-furrow slopes are considered, comparisons being made between two tractors that were reported upon in the University of Nebraska tests. The factors involving tractor stability and resistance against overturn are analyzed. The authors state that the analysis presents a definite method of attack for the more correct solution of the proper hitching-point, as well as being a study relating to lug design.

After generalizing on the need for greater consideration in automobile design for service and maintenance requirements, the author discusses the accessibility of car parts at some length with the idea of pointing out difficulties encountered by service-station mechanics when parts are inaccessible, this having a bearing also on the length of time required for repair work and the consequent increased cost to the car owner. Specific instances are given and illustrated in which improvements in design could be made to obviate trouble. These are inclusive of cylinders, cylinder blocks, pistons, bolts, cap-screws, nuts, valves, dashboard instruments and general take-up adjustment. Special emphasis is placed upon certain inaccessible parts that necessitate excessive dismantling.

Specifying the four general plans that have been followed by chassis builders in securing body equipment as being the building of bodies in their own shops; on contract by the body maker to plans and specifications of the chassis builder; by a local body maker to the order of the dealer or the owner; and the assembling from stock of standard sectional units recommended by the dealer or selected by the owner, the authors discuss each of these plans in detail. With regard to the plan of using standardized sectional bodies, the different sizes of chassis used for commercial purposes are separated into four specified groups and the production of a complete standard line including a number of styles of body for each chassis is commented upon and illustrated, inclusive of detailed considerations of the all-metal body.

The Chicago Service Meeting paper relates specifically to the type of garage equipment that is used to handle the motor vehicle in preparation for its repair. The devices illustrated and described are those designed to bring in disabled cars, and include wrecking cranes and supplementary axle trucks; portable cranes and jacks on casters for handling cars in a garage; presses, tire-changing equipment and wheel alignment devices; engine and axle stands; and miscellaneous minor apparatus. The different factors mentioned emphasize the great need of standardization. The thought is not to do away with a car's individuality, but to construct all parts so that cars may have efficient service to the highest degree through the agency of every serviceman.

After indicating the line of development since November, 1918, toward making the internal-combustion engine better adapted to aircraft service, the successful application of the supercharger to improve engine performance at great altitude is described and the over-dimensioned and over-compressioned engine also is discussed as a means toward that end. The use of anti-knock compounds to permit the use of high compression-ratios at small altitudes without knocking is commented upon and engine size is considered for both airplane and dirigible service. Further review includes air-cooling experiments in reference to the air-cooled radial engine, refinement of aviation-engine details, and improvements in aircraft powerplant parts and fuel-supply systems. For commercial aviation, powerplant reliability and low cost are stated as essentials. Illustrations are presented of the supercharger and of the engines and sylphon fuel-pump mentioned.

Stating that the means and methods of transporting freight over the highways are governed by six factors, the author enumerates them as being the number of ton-miles of goods to be shipped, the shipping points and destinations, the kinds of highway available, the types of vehicle most suitable, the cost of operation per ton-mile and the rates that should be charged for the service. The purpose of the paper is not to answer these questions but to determine whether present practice is headed in the right direction. The conditions the highway must meet, in addition to the gross load of the vehicles, are the maximum tire load, the pressure per square inch exerted by the tire upon the pavement and the value of any impact blow upon the pavement. The impact blows of pneumatic tires are practically negligible, while solid tires build up the impact to many times the weight of the wheel load; this is proved by impact tests of tires which are described in some detail and illustrated.

The author describes the research work on the internal-combustion engine done recently in his laboratory in England, and presents his deductions therefrom, based upon an analysis of the evidence he has obtained to date. Fuels are discussed at length under three specific headings, many tabular data being included and commented upon, and the calculation of thermal efficiency described. Mean volatility and detonation are discussed and the author's present views regarding turbulence are stated, this being followed by a brief summary of the conclusions reached by Mr. Tizard, a colleague of the author, following recent investigations. The influence of the nature of the fuel upon detonation is presented, a lengthy discussion of the subject of stratification being given under three specific divisions, inclusive of comment upon the benefits derived from using weak fuel-mixtures.

The paper is an exposition of the theoretical analysis made by the author of the experimental work of Woodbury, Canby and Lewis, on the Nature of Flame Movement in a Closed Cylinder, the results of which were published in THE TRANSACTIONS for the first half of 1921. No experimental evidence is presented by the author that has not been derived previously by other investigators. The relation of pressure to flame travel is derived first, the relation of mass burned is considered and a displacement diagram constructed, described and analyzed. The break of the flame-front curve, called the “point of arrest,” enters prominently into the discussion and computations; the pressure in the flame-front is studied; the reaction-velocities are calculated; and general comments are made.

Stating that present internal-combustion engine fuel is too low in volatility for economical use and that this is the cause of engine-maintenance troubles, the authors believe that, since it is not possible to obtain the more volatile grades in sufficient quantity, the only hope of remedying this condition is to learn how to use the heavy fuel, and that the most promising method of doing this lies in the effective use of heat. As the experimental data regarding the best temperature at which to maintain the metal in a hot-spot manifold and the range of temperatures available in the exhaust gases are meager, the authors experimented in the Purdue University laboratory to secure additional data. They present a summary of the results.