Search Results

Recuperated low-pressure-ratio split-cycle engines represent a promising engine configuration for applications like transportation and stand-alone power generation by offering a potential efficiency as high as 60%. However, it can be challenging to achieve the stringent NOx emission standard, such as Euro 6 limit of 0.4 gNOx/kWh, due to the exhaust cylinder high intake temperature. This paper presents experimental investigation of hydrogen-air combustion NOx emissions for such engines for the first time. Experiments are carried out using a simplified constant-volume combustion chamber with glow-plug ignition. Two fuel injection techniques are performed: direct injection and injection via a novel convergent-divergent injector. For the direct injection scenario, NOx levels are unsatisfactory with respect to the Euro 6 standards over a range of operating temperatures from 200 °C to 550 °C.

Modern automotive powertrains are operated using many control devices under a wide range of environmental conditions. The exhaust temperature must be controlled within a specific range to ensure low exhaust-gas emissions and engine-component protection. In this regard, physics-based exhaust-temperature prediction models are advantageous compared with the conventional exhaust-temperature map-based model developed using engine dyno testing results. This is because physics-based models can predict exhaust-temperature behavior in conditions not measured for calibration. However, increasing the computational load to illustrate all physical phenomena in the engine air path, including combustion in the cylinder, may not fully leverage the advantages of physical models for the performance of electric control units (ECUs).

To realize a super-leanburn SI engine with a very-high compression ratio, it is required to design a new fuel which could have low ignitability at a low temperature for antiknocking, but high ignitability at a high temperature for stable combustion. Ethane shows a long ignition delay time at a low temperature close to that of methane, but a short ignition delay time at a high temperature close to that of gasoline. In the present study, the antiknocking effect of adding methane with the RON of 120, ethane with the RON of 108, or propane with the RON of 112 to a regular gasoline surrogate fuel with the RON of 90.8 has been investigated. Adding each gaseous fuel by less than 0.4 in heat fraction advances knocking limit in the descending order of SI timing advance of ethane, methane, and propane, and in the descending order of CA 50 advance of ethane, propane, and methane. Adding methane extends combustion duration slightly, but adding ethane or propane shortens it considerably.

This work numerically investigated the methanol compression ignition combustion assisted with a glow plug (GP). The GP was positioned in the middle of the two intake ports. A heating power of 50 W was applied to maintain a quasi-steady temperature of 1323 K for the heating medium. Sensitivity analyses were conducted on various parameters affecting engine combustion characteristics and performance, including radial distance (RD) between the glow plug and injector, relative angle (RA) between the GP and its nearest jet, intake temperature, split ratio of pilot injection, and intake and injection pressures. Due to the complex fuel jet-GP interaction, the optimum RA shifted from 10° at RD = 22.5 mm to 17.5° at RD = 12.5 mm. The optimal RD among the studied values (12.5, 17.5, and 22.5 mm) was found to be 12.5 mm, achieving an indicated thermal efficiency (ITE) of 42.1% at RA = 17.5°.

High fuel stratification gasoline compression ignition (HFS-GCI) strategies allow for the use of ignition control methods similar to those used by diesel-fueled compression ignition (CI) engines while offering the emissions benefits of gasoline-like fuels. Despite this benefit, low load GCI operation requires ignition assistance viz. intake boosting, intake heating, cylinder deactivation, etc. for consistent autoignition. A novel ignition assistance methodology using an offset active prechamber (OAP) is proposed in this work to enable low load GCI operation. A 1.5cc OAP with a pressure-sensing spark plug and gaseous fuel injection system is designed and mounted in a medium-duty single-cylinder test engine based on the Cummins ISB engine. The prechamber is provided with two holes designed to ignite the fuel spray from the centrally mounted DI fuel injector. Gasoline was used as the main chamber fuel and methane was used as the prechamber fuel.

A comprehensive experimental study of hydrogen–diesel dual-fuel and hydrogen-hydrotreated vegetable oil (HVO) dual-fuel operations was conducted in a single-cylinder diesel engine (bore 85.0 mm, stroke 96.9 mm, and compression ratio 14.3) equipped with a common rail fuel injection system and a supercharger. The hydrogen flow rate was manipulated by varying the hydrogen excess air ratio from 2.5 to 4.0 in 0.5 increments. Hydrogen was introduced into the intake pipe using a gas injector. Diesel fuel and HVO were injected as pilot fuels at a fixed injection pressure of 80 MPa. The quantity of pilot fuel was set to 3, 6, and 13 mm3/cycle. The intake and exhaust pressures were set in the range of 100–220 kPa in 20 kPa increments. The engine was operated at a constant speed of 1,800 rpm under all conditions. The pilot injection timing was varied such that the ignition timing was constant at the TDC under all conditions.

In the context of energy conservation and emission reduction, high power density(HPD) and low fuel consumption are the consistent pursuit of diesel engine development. Among the small-bore diesel, the limited space in the cylinder poses higher challenges and requirements for the arrangement of sprays.The high injection pressure results in a greater impulse when the spray impinges chamber, which allows the combustibles to develop along the chamber wall. Based on these characteristics of small-bore HPD diesel, a reasonable injection scheme is proposed to help flame diffusion surface increasing and thermal efficiency enhancing. This work proposes an optimization path to increase the flame diffusion surface, then improve thermal efficiency. It can be achieved with matching between the injector extension length and the spray spray angle.