Search Results

Abstract Modern diesel engines temporarily use a very late post-injection in the combustion cycle to either generate heat for a diesel particulate filter regeneration or purge a lean NOx trap. In some configurations, unburned fuel is left at the cylinder walls and is transported via the piston rings toward the lower crankcase region, where fuel may dilute the oil. Reduced oil lubrication shortens the oil service intervals and increases friction. Beside diesel fuel, this problem may also occur for other types of liquid fuels such as alcohols and e-fuels. The exact transport mechanism of the unburned fuel via the piston ring pack grooves and cylinder wall is hard to measure experimentally, motivating numerical flow simulation in early design stages for an in-depth understanding of the involved processes.

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine engine throttles (gasoline or diesel) where push-pull cable control is applicable. For control cable information see SAE J917.

Brake caliper commonly utilizes rubber or spring components to maintain specific clearance range for sliding characteristics, rendering them susceptible to rattle noise. The Electro-Mechanical Brake (EMB) caliper has attracted attention for its advantageous features such as reduced brake drag, optimized vehicle layout, and precise brake control. However, the inclusion of additional components related to the dry-type pressurizing system results in increased caliper weight and susceptibility to rattle noise. This study thoroughly examines rattle noise characteristics in our prototype EMB caliper, identifying primary noise sources on the piston and guide-pin sides. Implementing piston seals and guide-pin boots tightening force proves the effectiveness in improving rattle noise characteristics. Collisions between the piston and ball-screw head can be mitigated by piston inner seal, significantly reducing rattle noise.

Vibrations in IC engines have a widespread effect on the operations of consumer and commercial vehicles, which not only affect the life and efficiency of the vehicle but also affect user comfort and nervous system of human body. This paper focuses on the comparative analysis of vibration and acoustic characteristics while utilizing fuels such as petrol and CNG. ADXL 335 3-axis accelerometer was employed to measure acceleration vs time data, which was then processed using MATLAB to obtain FFT and PSD plots. These plots thus obtained gave insights on dominating frequency as well as frequencies with maximum energy. Six different cases with different engine speeds and loading conditions are studied with analysis of all the different parameters such as sound pressure levels and mean and max cylinder pressure.

Abstract The present study explores the performance of high-density polyethylene (HDPE) pyrooil and ethanol blends with gasoline in SI engine using statistical modeling and analysis using response surface methodology (RSM) and the Anderson–Darling (AD) residual test. The pyrooil was extracted from HDPE through pyrolysis at 450°C and then distilled to separate the liquid fraction. Two blends were prepared by combining pyrooil and gasoline, and pyrooil–ethanol mixture (volume ratio of 9:1) and gasoline, both at volumetric concentrations ranging from 2% to 8% to evaluate brake thermal efficiency (BTE) and specific fuel consumption (SFC) in a SI engine. An experimental matrix containing speed, torque, and blend ratio as independent variables for both blends were designed, analyzed, and optimized using the RSM. The results show that a 4% blend of pyrooil with gasoline (P4) and a 6% blend of pyrooil–ethanol mixture with gasoline (P6E) were optimum for an SI engine.

Abstract The current research elucidates the application of response surface methodology to optimize the collective impact of methanol–isobutanol–gasoline blends and nanolubricants on the operational parameters of a spark-ignition engine. Diverse alcohol blends in conjunction with gasoline are employed in engine trials at 2500 rpm across varying engine loads. The alcohol blends exhibit notable enhancements in brake thermal efficiency, peak in-cylinder pressure, and heat release rate. At 2500 rpm and 75% load, the break thermal efficiency of iBM15 surpasses that of gasoline by 33.5%. Alcohol blends significantly reduce hydrocarbon and carbon monoxide emissions compared to gasoline. The iBM15 demonstrates a reduction of 25.2% and 51.12% in vibration along the Z and Y axes, respectively, relative to gasoline.

Abstract The article presents the results of simulation studies of pollutant emissions from passenger cars. The characteristics of emissions were determined using the vehicle driving test procedures, in consideration of differentiated average velocities as well as model traffic conditions: urban traffic jam, urban traffic with no congestion, rural, motorways, and highways. This article also presented the possibility of determining the characteristics of pollutant emission based on a singular realization of the vehicle velocities processes, as well as the intensity of pollutant emission, with the use of the Monte Carlo method. The pollutant emission characteristics enable specification of pollutant emission intensity, which can be used for the inventory of pollutant emissions from road transport (COPERT software applied as standard) and can be useful in the assessment of a degree of environmental hazard by modeling pollutant dispersion.

The fast acceleration of GHG (CO2 in particular) emitted by human activities into the atmosphere is accelerating the average temperature increase of our globe causing heavy climate change. This phenomenon has triggered a strong pressure on GHG emission reduction in all the human activities including the transportation sector which contributes for the 29% to the total emissions in EU [1]. A mitigation to this tendency can come from synthetic fuels: when produced by using clean energy, they can be considered CO2 neutral. H2 is the building block of synthetic fuels and can be used in spark ignited engines where releases the energy accumulated during its production. This solution is particularly attractive for HD applications thanks to the high energy density. H2 can be burned in a quite wide range of λ, but staying on 2,2 the amount of engine out NOx will be low enough for the use on a 13L engine with a relatively simple aftertreatment system.

Nowadays, green hydrogen can play a crucial role in a successful clean energy transition, thus reaching net zero emissions in the transport sector. Moreover, hydrogen exploitation in internal combustion engines is favored by its suitable combustion properties and quasi-zero pollutant emissions. High flame speeds enable a lean combustion approach, which provides high efficiency and reduces NOx emissions. However, high airflow rates are required to achieve the load levels typical of heavy-duty applications. In this framework, the present study aims at investigating the required boosting system of a 6-cylinder, 13-litre heavy-duty spark ignition engine through 1D numerical simulation. A comparison among various architectures of the turbocharging system and the size of each component is presented, thus highlighting the limitations and potentialities of each architecture and providing important insights for the selection of the best turbocharging system.

Due to its physical and chemical properties, hydrogen is an attractive fuel for internal combustion engines, providing grounds for studies on hydrogen engines. It is common practice to use a mathematical model for basic engine design and an essential part of this is the simulation of the combustion cycle, which is the subject of the work presented here. One of the most widely used models for describing combustion in gasoline and diesel engines is the Wiebe model. However, for cases of hydrogen combustion in DI engines, which are characterized by mixture stratification and in some cases significant incomplete combustion, practically no data can be found in the literature on the application of the Wiebe model. Based on Wiebe’s formulas, a mathematical model of hydrogen combustion has been developed. The model allows making computations for both DI and PFI hydrogen engines. The parameters of the Wiebe model were assessed for three different engines in a total of 26 operating modes.

Combustion characteristics of a hydrogen (H2) direct-injected (DI) pre-chamber (PC)-assisted opposed piston two-stroke (OP2S) engine are investigated by 3D computational fluid dynamics (CFD) simulations. The architecture of the OP2S engine has potential features for reducing wall heat losses, as the DI H2 jets are not directed towards the piston face. To overcome the high resistance to autoignition of H2, a PC technology was implemented in order to enhance the ignition of the mixture by the multiple hot reactive jets. To further investigate the interaction between the H2 plume and the chamber walls, three different piston bowl designs were evaluated and ranked based on a merit function. For the cases under study, the flat piston design was found to be most favorable (compared to the narrow and wide pistons) due to its reduced surface area for lower wall heat losses.

Abstract TOC

Heavy duty engines for long-haul trucks are quite difficult to electrify, due to the large amount of energy that should be stored on-board to achieve a range comparable to that of conventional fuels. In particular, this paper considers a stock engine with a displacement of 12.9 L, developed by the manufacturer in two different versions. As a standard diesel, the engine is able to deliver about 420 kW at 1800 rpm, whereas in the compressed natural gas configuration the maximum power output is 330 kW, at the same speed. Three possible alternatives to these fossil fuels are considered in this study: biodiesel (HVOlution by Eni), bio-methane and green hydrogen. While the replacement of diesel and compressed natura gas with biofuels does not need significant hardware modifications, the implementation of a hydrogen spark ignition combustion system requires a deep revision of the engine concept.

The reduction of anthropogenic greenhouse gas emissions and ever stricter regulations on pollutant emissions in the transport sector require research and development of new, climate-friendly propulsion concepts. The use of renewable hydrogen as a fuel for internal combustion engines promises to provide a good solution especially for commercial vehicles. For optimum efficiency of the combustion process, hydrogen-specific engine components are required, which need to be tested on the test bench and analysed in simulation studies. This paper deals with the simulation-based investigation and optimisation of fuel injection in a 6-cylinder PFI commercial vehicle engine, which has been modified for hydrogen operation starting from a natural gas engine concept.

Hydrogen engines are currently considered as a viable solution to preserve the internal combustion engine (ICE) as a power unit for vehicle propulsion. In particular, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations, due to their reduced emission levels and high thermodynamic efficiency. Lean charge is suitable for the purpose of passenger car applications, where the demand of mid/low power output does not require an excessive amount of air to be delivered by the turbocharging unit, but can difficulty be tailored in the field of high performance engine, where the air mass delivered would require oversized turbocharging systems or more complex charging solutions. For this reason, the range of feeding conditions near the stochiometric value is explored in the field of high performance engines, leading to the consequent issue of abatement of pollutant emissions.

This work aims at investigating the optimal configuration of an internal combustion engine fueled with bio-ethanol for improving its brake power and efficiency as well as for reducing the NOx emissions, in stationary applications. A turbocharged spark ignition engine characterized by a single-point injection was preliminarily considered; subsequently, a direct injection configuration was investigated. For both cases, a 1-D numerical model was developed to compare the injection configurations under stoichiometric conditions and different spark timings. The analysis shows that the direct injection guarantees: a limited improvement of brake power and efficiency when the same spark timing is adopted, while NOx emissions increases by 20%; an increase of 6% in brake power and 2 percentage points in brake thermal efficiency by adopting the knock limited spark advance, but an almost double NOx emissions increase.

This study explores the feasibility of using a sustainable lignin-based fuel, consisting of 44 % lignin, 50 % ethanol, and 6 % water, in conventional compression ignition (CI) marine engines. Through experimental evaluations on a modified small-bore CI engine, we identified the primary challenges associated with lignin-based fuel, including engine startup and shutdown issues due to solvent evaporation and lignin solidification inside the fuel system, and deposit formation on cylinder walls leading to piston ring seizure. To address these issues, we developed a fuel switching system transitioning from lignin-based fuel to cleaning fuel with 85 vol% of acetone, 10 vol% of water and 5 vol% of ignition improving additive, effectively preventing system clogs.

Abstract Dimethyl ether (DME) is an alternative fuel that, blended with propane, could be an excellent alternative for exploring the use of fuels from renewable sources. DME–propane blends are feasible for their comparable physicochemical properties; these fuels may be pressured as liquids using moderate pressure at ambient temperature. Adding a proportion of DME with a low octane number to a less reactive fuel like propane can improve the combustion process. However, the increased reactivity of the mixture induced by the DME could lead to the early appearance of knocking, and this tendency may even be pronounced in boosted SI engines.