Search Results

Detroit Section Paper - Since a gear is a product of the cutting tool, the gear-cutting machine and the operator, it can be no more accurate than the combined accuracy of these fundamental factors. All gear manufacturers aim to eliminate split bearings, high and low bearings, flats and other inaccuracies in tooth contour, because a gear having teeth the contours of which comply with the geometrical laws underlying its construction is by far the most satisfactory. Illustrations are presented to convey an understanding of the geometrical principles involved, together with other illustrations of testing instruments and comments thereon. The application of these instruments is termed quality control, which is discussed in some detail under the headings of hob control, machine control and gear control.

The author discusses only gear-grinding work on gear teeth subsequent to heat-treatment and pays particular attention to automobile transmission gears. He states that as yet very little is being done in the grinding of gear teeth that have not been heat-treated. The salvaging of gears that have been rejected and the finish-grinding of gears that have grinding stock remaining upon the teeth are commented upon, together with remarks on the cost of grinding, the history of gear grinding, the different classes of work performed, gear-grinding machines in general, tooth-form and gear wear. It is stated that gear grinding is commercially a production operation having as its aim the placing of the correct tooth-shape and proper surface-finish on gear teeth so that the gears can move accurately, noiselessly and without wear; and that the cost of finished acceptable transmissions is less than when the process of finish-grinding is used.

A record of an investigation of heavy-duty truck-axles carried out by the Bureau of Standards at the request of the motor transport division of the Quartermaster Corps, this paper deals in particular with the mechanical efficiency of the axles tested. The investigation included, in addition to several worm-drive Class-B Army-truck axles with different types of bearing, a number of axles usually designated respectively as “internal-gear” and “multiple-reduction” type. Each of these types was represented by axles in successful use in commercial trucks of 5-ton rating. In analyzing the results of the tests it was found possible to separate the losses into no-load losses and load losses; the total loss being the sum of these two. In general, the no-load losses were primarily controlled by the viscosity and the method of application of the lubricant. They were greater in those axles in which the parts rotating at high speeds were immersed most completely in the lubricant.

The author quotes statistics relating to the proportion of closed to open bodies and outlines the changes that have taken place in body construction in recent years. He sketches the advances that have been made and states that the question to be answered now relates to what all this improvement in manufacturing methods has accomplished toward reducing the price of a closed-car body to the consumer. He compares the percentage of public benefit in 1922 with that of 1914, excluding the period of inflated prices immediately following the war, and states that it is 10 to 15 per cent, but says also that this is an unfair comparison because of the excessive increases in the cost of labor, lumber, sheet steel and trimming cloth. An unconventional type of body, covered entirely with fabric over a foundation of wire-mesh and buckram fastened to the conventional wood-framing, is illustrated and described in detail, together with a statement of its advantages.

The author states briefly the phenomenal growth of taxicab usage and consequent demand for this type of motor vehicle, mentioned the differences in body requirements for taxicabs as compared with those of passenger cars, and describes the methods used to secure durability in taxicab-body construction to discount the severe service to which the body is subjected. Tabular data are presented and comments made regarding the woods that are suitable for body framework, and the methods of joining frame members and reinforcing frame joints are outlined. The desirable types of roof and the factors that influence design are discussed at some length, illustrations being presented also, and minor considerations, such as types of hardware, dash and instrument-boards, are included. A brief summary states present conditions, and a bibliographical list is appended of informative publications relating to the subject.

Annual Meeting Paper - The heat-dissipating properties of three types of radiator core have been investigated at the Mason Laboratory, Yale University. These include the fin-and-tube, the ribbon and the air-tube groups, so classified according to the flow of the water and the air. The ratio of the cooling surface to the volume is shown to be nearly the same in the fin-and-tube and the air-tube cores, while that of the ribbon core is somewhat greater. A formula is derived for computing the heat-transfer coefficient, which is defined as the number of heat units per hour that will pass from one square foot of surface per degree of temperature-difference between the air and the water and is the key to radiator performance, as by it almost any desired information can be obtained. When the heat-transfer coefficients have been found for a sufficiently wide range of water and air-flows the cooling capacity of a radiator can be computed for any desired condition.

This Annual Meeting paper is a report of a series of tests conducted during the summer of 1922 by the authors at the Engineering Experiment Station of Purdue University. The work consisted of research into the operation of internal-combustion engines under comparatively high compression on ordinary gasoline without detonation. The compression-ratio of the engine was 6.75 and the compression pressure was 122 lb. per sq. in., gage. The ingoing charge was passed through a hot-spot vaporizer and thence through a cooler between the carbureter and the valves. Jacket-water temperatures between 150 and 170 deg. fahr. were carried at the outlet port of the jacket. The theory held by the authors as to the causes of detonation of the combustible charge is presented briefly. The source of the two phases of detonation encountered in this work is believed to be overheated areas in the combustion-chamber.

After pointing out that the publication of articles in the trade and technical journals, to the effect that very considerable weight-reductions in motor-truck construction with consequent savings in gasoline and tires are possible, works an injustice to the motor-truck industry and is misleading, the author outlines some of the reasons why such weight-reductions are very difficult to effect, as well as the possibilities of standardizing axle details. The use of aluminum to effect weight-reduction is commented upon and the various advantages claimed for metal wheels are mentioned. In the latter connection the author points out that, while these claims may be true, they are unsupported by reliable data. The greater part of the paper is devoted to an account of a series of tests conducted by a large coal company to determine the relative merits of wood and metal wheels on its trucks.

The different gear noises are classified under the names of knock, rattle, growl, hum and sing, and these are discussed at some length, examples of defects that cause noise being given and a device for checking tooth spacing being illustrated and described. An instrument for analyzing tooth-forms that produce these different noises is illustrated and described. Causes of the errors in gears may be in the hardening process, in the cutting machines or in the cutters. A hobbing machine is used as an example and its possibilities for error are commented upon. Tooth-forms are illustrated and treated briefly, and the hardening of gears and the grinding of gear-tooth forms are given similar attention.

While investigating the sources and causes of noise in automobiles during an extensive connection with one of the largest automobile companies, the authors recorded their experiences in the shop in the form of notes. Some of these are offered with a view to stimulating the discussion of the subject and with the hope that additional information will be brought out by an exchange of ideas, particularly on the problem of eliminating gear-noises. In many cases they found that noise was caused by failure to allow sufficient clearance for an adequate oil-film. And it was noted frequently that when one noise had been located and silenced another appeared that had not been apparent before. The topics that have been considered include the running-in of brake-bands, engine knocks, oil-pump gear-noise and that of gears in general, the clearances of ball bearings, backlash, and rear-axle bevel-gears.

The process devised by the author was evolved to eliminate the difficulties incident to the finishing of the spline and body portions of a spline shaft, such as is used in transmission gearing, by grinding after the shaft has been hardened, and is the result of a series of experiments. The accuracy of the finished shaft was the primary consideration and three other groups of important considerations are stated, as well as four specific difficulties that were expected to appear upon departure from former practice. Illustrations are presented to show the tools used, and the method of using them is commented upon step by step. The shaft can be straightened to within 0.005 in. per ft. of being out of parallel with the true axis of the shaft, after the shaft has been hardened, and it is then re-centered true with the spline portion.

Cleveland Section paper - After commenting upon the two contradictory attitudes toward malleable iron in the automotive industry and outlining its history briefly, the authors discuss the differences between malleable and ordinary gray-iron and supplement this with a description of the heat-treating of malleable castings. Five factors that influence the machining properties of malleable-iron are stated. These were investigated in tests made with drills having variable characteristics that were governed by six specified general factors. Charts of the results are presented and commented upon in some detail, inclusive of empirical formulas and constants and deductions made therefrom.

The author gives a short history and general description of duralumin and quotes the Navy specification of its physical properties as drawn by the Naval Aircraft Factory. The manufacture of duralumin is described and commented upon, inclusive of an enumeration of the improvement in physical properties produced at each stage. The physical properties are stated for annealed, heat-treated and hard-rolled duralumin, and some of the possible automotive applications are suggested, inclusive of wormwheels, hearings, gears, connecting-rods, rims and wheel parts and chassis and body trimming. A report by the research department of the Fifth Avenue Coach Co. on the results of a test it made on duralumin wormwheels is included and the author details the advantages he claims as being attendant upon the use of duralumin.

The gradual trend toward overhead valves in automobile engines, as indicated by an increase in their use on American cars from 6 per cent in 1914 to 31 per cent in 1922, has been accelerated, in the opinion of the author, by their successful application to aircraft engines and by the publicity given them by their almost universal adoption on racing machines. Tractor engines recently brought out show the advantage of this construction.

The author believes the piston-ring problem to be an engineering one worthy of serious study and that it should be possible to standardize types and sizes in a way that will go far toward elminating present difficulties. It is stated that cast iron is the only satisfactory metal suitable for use in the internal-combustion engine and that the foundry offers the greatest opportunity for improvement, in the elimination of poor castings. The superiority of individually cast rings is averred and a formula for their composition is given. Leakage and oil-pumping are discussed, followed by comment upon the width and form most desirable for piston-rings; and some of the difficulties of their manufacture are enumerated, together with suggested improvements, inclusive of inspection and testing methods.

The authors present and discuss the results obtained from combined road and laboratory tests made to determine the amount of power required to maintain a given car speed. The specifications of the car and its engine are stated and the variable-ratio rocker-arm of the engine is illustrated and its advantages explained, together with those of the valve-timing. The subject of manifold gas-velocity is treated in some detail, inclusive of a diagram showing the hot-spot or vaporizing device that was used. The test data are reduced to curve form, eight charts being shown. The curves include those for brake horsepower, indicated horsepower, comparative performance, performance at different throttle-openings and at different loads, fuel consumption and indicated thermal efficiencies.

After pointing out that the general question of weight reduction is no exception to the fallacies that seem to have beset the development of the automobile from its earliest days, the author outlines briefly the problem confronting the automobile designer. The influence of the weight of the reciprocating parts on the chassis in general and the engine in particular is emphasized as being of greater importance than the actual saving in the weight of the parts themselves, it being brought out that the bearing loading due to inertia is really the factor that limits the maximum engine speed. Reference is made to the mathematical investigation by Lanchester in 1907 of the advantages of using materials of high specific-strength and the conclusions arrived at are quoted in full. A tabulation of the specific strengths of various materials used in automotive engineering practice is presented as showing the advantages of aluminum as compared with steel.

Metropolitan-New England Sections Paper - The loss of power due to the friction of the various parts of the chassis has been carefully and elaborately investigated by a dynamometer, the dual purpose being the determination of the amount of internal frictional resistance of the front or rear wheels and the measurement of the power that can be delivered at the rear wheels with the concomitant rate of fuel consumption. The rolling-friction due to the resistance of the wheels as a whole is taken up first and afterward the separate resistances of the tires, bearings and transmission are studied under varying conditions of inflation-pressure and load. The five frictional resistances that were chosen as giving the most useful information are those of the front tires, the rear tires, the front bearings, the rear bearings and the engine.

Annual Meeting Paper - Addressing the structural engineer and the purchasing agent particularly, the author discusses the relationship between them and the foundryman with regard to malleable-iron castings and enumerates foundry difficulties. The characteristics necessitating adequate gating for such castings are described and illustrated, inclusive of considerations regarding pattern design, followed by a statement of the considerations that should influence the purchasing agent when dealing with foundrymen. Possible casting defects are described, illustrated and discussed, comment being made upon casting shrinkage and machinability. Improvements in annealing-oven construction and operation are reviewed and the records of 100 consecutive heats in different plants are tabulated. The materials for casting that compete with malleable iron are mentioned and its physical characteristics are considered in some detail.