Search Results

Natural gas as an internal combustion engine fuel is taking a predominant role as a mid-term solution to pollution due to combustion driven human activities both in the energy and transport sectors. Engine researchers and manufacturers are in the process of investigating and improving strategies that decrease emissions and fuel consumption, without compromising engine performance and efficiency; active pre-chamber configurations are to be accounted for as one of these. A relatively small amount of fuel (up to 10 % of the total fuel-energy requirement) is introduced in the confined volume of the pre-chamber and forms a close-to-stoichiometric mixture with fresh charge that is introduced from the main combustion chamber during the compression stroke. After spark-ignition the products of this early stage of combustion can ignite ultra-lean mixtures (with λ up to 2) through the Turbulent Jet Ignition mechanism, hence reducing fuel consumption as well as noxious emissions such as NOx.

Increasing combustion pressure, low viscosity oils, less oil supply and the increasing stress due to downsizing of internal combustion engines (ICE) lead to higher loads within the bearing. As the mechanical and tribological loads on the piston pin bearings have a direct impact on the service life and function of the overall engine system, it is necessary to develop a robust tribological design approach. Regarding the piston pin bearing of a diesel engine, this study aims to describe the effects of different parameters on a DLC-coated piston pin within the bearing. Therefore, an external engine part test rig, which applies various forces to the connecting rod and measures the torque on a driven pin, is used to carry out validation measurements. The special feature of the test bench is the way the piston is beared. For the first experiments, the piston crown is placed against a plate (plate-bearing); later, this plate-bearing is replaced by a hydrostatic bearing.

The introduction of real driving emissions cycles and increasingly restrictive emissions regulations force the automotive industry to develop new and more efficient solutions for emission reductions. In particular, the cold start and catalyst heating conditions are crucial for modern cars because is when most of the emissions are produced. One interesting strategy to reduce the time required for catalyst heating is post-oxidation. It consists in operating the engine with a rich in-cylinder mixture and completing the oxidation of fuel inside the exhaust manifold. The result is an increase in temperature and enthalpy of the gases in the exhaust, therefore heating the three-way-catalyst. The following investigation focuses on the implementation of post-oxidation by means of scavenging in a four-cylinder, turbocharged, direct injection spark ignition engine. The investigation is based on detailed measurements that are carried out at the test-bench.

Currently, conventional spark-ignition engines are unfit to satisfy the growing customer requirements on efficiency while complying with the legislations on pollutant emissions. New ignition systems are being developed to extend the engine stable operating range towards increasing lean conditions. Among these, the Radio-Frequency corona igniters represent an interesting solution for the capability to promote the combustion in a much wider region than the one involved by the traditional spark channel. Moreover, the flame kernel development is enhanced by means of the production of non-thermal plasma, where low-temperature active radicals are ignition promoters. However, at low pressure and at high voltage the low temperature plasma benefits can be lost due to occurrences of spark-like events. Recently, RF barrier discharge igniters (BDI) have been investigated for the ability to prevent the arc formation thanks to a strong-breakdown resistance.

Internal combustion engines are the primary transportation mover for today society and they will likely continue to be for decades to come. Hybridization is the most common solution to reduce the petrol-fuels consumption and to respect the new raw emission limits. The gasoline engines designed for running together with an electric motor need to have a very high thermal efficiency because they must work at high loads, where engine thermal efficiency is close to the maximum one. Therefore, the technical solutions bringing to thermal efficiency enhancement were adopted on HVs (Hybrid Vehicles) prior to conventional vehicles. In these days, these solutions are going to be adopted on conventional vehicles too. The purpose of this work was to trace development guidelines useful for engine designers, based on the target power and focused on the maximization of the engine thermal efficiency, following the engine rightsizing concept.

Water injection represents a promising tool to improve performance of spark-ignition engines. It allows reducing in-cylinder temperature, preventing knock risks. Optimizing the spark advance, water injection allows obtaining an increase of both efficiency and power output, particularly at medium and high loads. Water can be injected into the intake port or directly into the combustion chamber. In this paper, the authors investigated the effects of both direct and port water injection in a downsized PFI spark-ignition engine at high load operation. Different water-to-fuel ratios have been analyzed for both configurations. For the experimental analysis, low-pressure water injectors have been installed in the intake ports of the engine under study, upstream of the fuel injectors. Experimental tests have been carried out at various operating points. Furthermore, engine operation with port water injection has been simulated by means of the AVL Fire 3-D code.

This work focuses on the development and validation of a data-driven model capable of predicting the maximum in-cylinder pressure during the operation of an internal combustion engine, with the least possible computational effort. The model is based on two parameters, one that represents engine load and another one the combustion phase. Experimental data from four different gasoline engines, two turbocharged Gasoline Direct Injection Spark Ignition, a Naturally Aspirated SI and a Gasoline Compression Ignition engine, was used to calibrate and validate the model. Some of these engines were equipped with technologies such as Low-Pressure Exhaust Gas Recirculation and Water Injection or a compression ignition type of combustion in the case of the GCI engine. A vast amount of engine points were explored in order to cover as much as possible of the operating range when considering automotive applications and thus confirming the broad validity of the model.

The development of highly boosted and high compression spark-ignition engines with enhanced thermal efficiencies is primarily limited by knock and super-knock. Super-knock is an excessively high intensity knock which has been related to a developing detonation process. This study investigates the knocking tendency of different gasoline surrogate fuels with varying research octane numbers (RON), octane sensitivity (S) and composition. The ξ/ɛ diagram with an enclosed detonation peninsula is used to assess the knocking tendency of different fuels. The diagram plots ξ, the ratio of acoustic to auto-ignitive velocity, against ɛ, the ratio of the transit time of an acoustic wave through a hot spot, to the heat release time (τe). Constant volume simulations of auto-ignition delay times (τi) and excitation times (τe) obtained from chemical kinetic calculations, enable calculations of ξ and ɛ.

Nowadays internal combustion engines can operate under lean combustion conditions to maximize efficiency, as long as combustion stability is guaranteed. The robustness of combustion initiation is one of the main issues of actual spark-ignition engines, especially at high level of excess-air or dilution. The enhancement of the in-cylinder global motion and local turbulence is an effective way to increase the flame velocity. During the ignition process, the excessive charge motion can hinder the spark discharge and eventually cause a misfire. In this perspective, the interaction between the igniter and the flow field is a fundamental aspect which still needs to be explored in more detail to understand how the combustion originates and develops. In this work, a combined experimental and numerical study is carried out to investigate the flow field around the spark gap, and its effect on the spark discharge evolution.

Internal combustion engine will remain the major propulsion system for land transportation, for at least the next decade, as the transition to full electrification will not be imminent. Thus, it is important to improve the combustion efficiency and emissions. To achieve this, it is important to understand and control the in - cylinder flow evolution, and primarily the Tumble development as this is strongly connected with the mixing process. Flow field measurements were obtained by using Time Resolved Particle Image Velocimetry technique in a 475cc optical single - cylinder Gasoline Direct Injection (GDI) spark ignition engine. The results include 50 consecutive cycles phase averaged velocity fields at 2000 RPM with wide open throttle.

Engine calibration involves the interaction of electronic components with various engine systems like intake system, exhaust system, ignition system, etc. Emissions are the by-products of combustion of fuel and air inside the combustion chamber. After-treatment systems generally take up the responsibility to scrape out harmful emissions from the engines. However, a good engine calibration will focus on emission reduction at source i.e., during the combustion itself. Thus, the intake of air and fuel in proper amount at each engine operating point is crucial for optimized engine performance and minimal emissions. The Intake system is an integral part of any internal combustion engine and it plays an important role to improve its performance and emission. Generally, for a SI engine, maintaining the stoichiometric A/F ratio is a challenging endeavour from an operational standpoint.

In a Passive suspension, a shock absorber generates damping force by pressurizing the oil flow between chambers. Typically, vehicle responds with suspension deflection, which significantly depends on damping forces and suspension velocity. Tuning dampers for various roads and steering input is an iterative balancing process. In any setting, damping force w.r.t velocity is tuned for optimum ride and handling performance. Practically, to achieve a balance between the two is a tedious task as the choices & arrangements of inner parts like piston, port, valve etc., which defines the forces set up [soft / hard] are almost infinite. The objective of this paper is to measure, objectify and evaluate the performance of two such optimum setting in various ride and handling events. A passenger car set up with an optimum soft & hard suspension damping force is studied for various ride and handling sub-attributes and their conflicts are examined in detail from a performance point of view:

The present work is focused on getting insight into premixed hydrogen fueled spark ignition engine using numerical simulations. Combustion simulations with reduced kinetics have been validated with experiments and the validated model has been used for a parametric study. A clear transition in combustion characteristics has been observed at a threshold of 0.6 equivalence ratio. Flame propagation speed has been estimated by image processing OH mass fraction contours from simulations. This has been compared to laminar flame speed obtained from 1D tools to understand the transition of flame towards turbulent. NO formation has been observed to increase till an equivalence ratio of 0.8 due to an increase in flame temperature and decrease with further increase in equivalence ratio due to late cycle dissociation. The findings reported in this study shall be helpful in optimizing combustion systems for hydrogen fueled spark ignition engines to overcome flame extinction and reduce NO emissions.

It is well known that alcohol based fuels may have been regarded as one of the alternative fuels because they have several physical and combustion properties similar to gasoline. Ethanol and butanol are alcohols considered as the most promising biocomponents for currently used conventional fuels. However, taking into account the numerous advantages of butanol over ethanol, and its properties, closer to those of gasoline, it is believed that it has greater application potential in the future environmentally-friendly fuels. For these reasons, butanol is under consideration to replace ethanol as an alternative fuel to gasoline especially as a gasoline blending bio-component. Therefore, this paper is focusing on the assessment of the influence of butanol addition to gasoline on harmful deposit formation in a various generation of spark ignition engine. Currently, only few research papers had discussed in very general this very important problem.

It is widely believed that fuel components of spark-ignition engines are mainly light alcohols. In order to change this state of affairs, it was assumed that it is possible to create fuel mixtures with heavy alcohols or light and heavy alcohols together, obtaining in latter case alternative ternary fuels. The hypothesis was adopted that such a fuel blend may contain any proportion of individual components. The truth of the hypothesis was demonstrated by preparing a number of mixtures of isooctane with ethyl and butyl alcohol, which were homogeneous and did not stratify even after prolonged storage. The research methodology adopted in this study is based on the assumption that composition of ternary fuels should be consistent with the relevant design of experiment, while assessment of the impact of composition on engine parameters should be made by operating a multi-equation mathematical model, and each of these equations, as a sub-model, must be statistically verified.

One of the first tasks while designing pistons is to ensure the reliable engine operation with minimal friction losses. This is possible by ensuring the liquid friction in the piston-cylinder junction during the entire operating cycle. Therefore, it is important to assess the nature of friction in the piston-cylinder conjunction. This task can be broken down into a number of interrelated subtasks: determining the characteristics of the piston lateral movement, determining the piston deformations under thermal and mechanical loads, and calculating the hydrodynamic forces acting from the side of the oil layer in the conjunction. The use of software packages that solve these problems separately and their inclusion in the iterative process will lead to huge expenditures of computing time and is difficult to implement in carrying out design optimization problems.

Cycle-To-Cycle Variability (CCV) must be properly considered when modeling the ignition process in SI engines operating with ultra-lean mixtures. In this work, a strategy to model the impact of the ignition type on the CCV was developed using the RANS approach for turbulence modelling, performing multi-cycle simulations for the power-cycle only. The spark-discharge was modelled through a set of Lagrangian particles, introduced along the sparkgap and interacting with the surrounding Eulerian gas flow. Then, at each discharge event, the velocity of each particle was modified with a zero-divergence perturbation of the velocity field with respect to average conditions. Finally, the particles velocity was evolved according to the Simplified Langevin Model (SLM), which keeps memory of the initial perturbation and applies a Wiener process to simulate the stochastic interaction of each channel particle with the surrounding gas flow.

Assessment of the boundaries for self-ignition of unburned charge in spark ignition engines (also related to knock) is required for development of the engine concepts and controls with respect to charge composition, spark advance and valve timing when designing the gas engines with wide range of the fuel compositions and converting compression ignition engines to gas engines. In this paper the combination of the single-zone model of the SI engine and chemical kinetics modeling is evaluated as a rapid prototyping tool for prediction of the self-ignition of the unburned charge in SI engine. The single-zone model simulates the cylinder pressure history based on Wiebe heat release function. The simulation of the self-ignition of the unburned charge is performed with coupled solution of the system of ordinary differential equations for temperature and species concentration with detailed chemical kinetic mechanism. Three fuels were considered: primary reference fuel, methane, hydrogen.

Despite a long history of development, modern spark-ignition (SI) engines are still restricted in obtaining higher thermal efficiency and better performance by knock. Knocking combustion is an abnormal combustion phenomenon caused by the autoignition of unburned air-fuel mixture ahead of the propagating flame front. This work describes investigations into the significance of spark plug location (with respect to inlet and exhaust valve position) on the knock formation mechanism. To facilitate the investigation, four spark plugs were installed in a specialized liner at four equispaced distinct locations to propagate flames from those locations, which provoked a distinct flame propagation from each and thus individual autoignition profiles. Six pressure transducers were arranged to precisely record the pressure oscillations, knock intensities, and combustion characteristics.

The arc characteristics and discharge behavior of a representative inductive spark ignition system were characterized with a spark plug calorimeter and a constant volume vessel used to create high-pressure crossflow velocities through the gap of the spark plug. A 14 mm diameter natural gas engine spark plug was used for the measurements. The discharges were into a non-combusting gas, primarily nitrogen. The spark plug calorimeter was used to determine the electrical-to-thermal energy conversion in the spark gap under quiescent conditions, while the constant volume vessel was used to study ignition arc structure in convective crossflows and imaged with a high-speed camera. Topics included the effect of crossflow velocity, pressure (up to 20 bar at 300 K), and gap distance on breakdown voltage, arc duration and delivered electrical energy. Also of interest was the amount of remaining electrical energy on the coil versus spark duration in a cross flow.