Refine Your Search


Search Results

Viewing 1 to 15 of 15
Technical Paper

Powertrain Calibration Techniques

Meeting the particle number (PN) emissions limits in vehicle test sequences needs specific attention on each power variation event occurring in the internal combustion engine (ICE). ICE power variations arise from engine start onwards along the entire test drive. In hybrid systems, there is one further source for transient ICE response: each power shift between E-motor and ICE introduces gas flow variations with subsequent temperature response in the ICE and in the engine aftertreatment system (EAS). This bears consequences for engine out emissions as well as for the EAS efficiency and even for the durability of a catalytic converter. As system calibration engineers must decide on numerous actuator parameters, their decisions, finally, are crucial for meeting legislative limits under the boundary conditions given by the hybrid vehicle’s drive environment.
Journal Article

Solutions for Emission Robustness of BS VI Phase II Respecting the Market Specific Requirements

Most stringent emission legislations have been implemented in all major markets to improve air quality across the past years. This effects the product cost of the vehicles which is considered being critical and needs to be minimized. India suffers from bad air quality and countermeasures have been defined. One being the implementation of similar emission standards than EU VI. By doing so, India takes a large step going from the currently effective BS IV directly to BS VI. Emission reduction is currently mainly handled by the usage of EGR, thus no engine aftertreatment system has been applied. BS VI will require an aftertreatment (EAS) concept with several catalysts and corresponding control system. India is a very cost sensitive market and a carry over of solutions from the EU needs to be evaluated carefully and new approaches need to be found.
Technical Paper

A Correlation Methodology between AVL Mean Value Engine Model and Measurements with Concept Analysis of Mean Value Representation for Engine Transient Tests

The use of state of the art simulation tools for effective front-loading of the calibration process is essential to support the additional efforts required by the new Real Driving Emission (RDE) legislation. The process needs a critical model validation where the correlation in dynamic conditions is used as a preliminary insight into the bounds of the representation domain of engine mean values. This paper focuses on the methodologies for correlating dynamic simulations with emissions data measured during dynamic vehicle operation (fundamental engine parameters and gaseous emissions) obtained using dedicated instrumentation on a diesel vehicle, with a particular attention for oxides of nitrogen NOx specie. This correlation is performed using simulated tests run within AVL’s mean value engine and engine aftertreatment (EAS) model MoBEO (Model Based Engine Optimization).
Technical Paper

Crank-Angle Resolved Modeling of Fuel Injection, Combustion and Emission Formation for Engine Optimization and Calibration on Real-Time Systems

The present work introduces an innovative mechanistically based 0D spray model which is coupled to a combustion model on the basis of an advanced mixture controlled combustion approach. The model calculates the rate of heat release based on the injection rate profile and the in-cylinder state. The air/fuel distribution in the spray is predicted based on momentum conservation by applying first principles. On the basis of the 2-zone cylinder framework, NOx emissions are calculated by the Zeldovich mechanism. The combustion and emission models are calibrated and validated with a series of dedicated test bed data specifically revealing its capability of describing the impact of variations of EGR, injection timing, and injection pressure. A model based optimization is carried out, aiming at an optimum trade-off between fuel consumption and engine-out emissions. The findings serve to estimate an economic optimum point in the NOx/BSFC trade-off.
Journal Article

Modeling of Catalyzed Particulate Filters - Concept Phase Simulation and Real-Time Plant Modeling on HiL

The present work introduces an extended particulate filter model focusing on capabilities to cover catalytic and surface storage reactions and to serve as a virtual multi-functional reactor/separator. The model can be classified as a transient, non-isothermal 1D+1D two-channel model. The applied modeling framework offers the required modeling depth to investigate arbitrary catalytic reaction schemes and it follows the computational requirement of running in real-time. The trade-off between model complexity and computational speed is scalable. The model is validated with the help of an analytically solved reference and the model parametrization is demonstrated by simulating experimentally given temperatures of a heat-up measurement. The detailed 1D+1D model is demonstrated in a concept study comparing the impact of different spatial washcoat distributions.
Journal Article

Evaluation of Valve Train Variability in Diesel Engines

The continuously decreasing emission limits lead to a growing importance of exhaust aftertreatment in Diesel engines. Hence, methods for achieving a rapid catalyst light-off after engine cold start and for maintaining the catalyst temperature during low load operation will become more and more necessary. The present work evaluates several valve timing strategies concerning their ability for doing so. For this purpose, simulations as well as experimental investigations were conducted. A special focus of simulation was on pointing out the relevance of exhaust temperature, mass flow and enthalpy for these thermomanagement tasks. An increase of exhaust temperature is beneficial for both catalyst heat-up and maintaining catalyst temperature. In case of the exhaust mass flow, high values are advantageous only in case of a catalyst heat-up process, while maintaining catalyst temperature is supported by a low mass flow.
Technical Paper

High Power Discharge Combustion Effects on Fuel Consumption, Emissions, and Catalyst Heating

A key element to achieving vehicle emission certification for most light-duty vehicles using spark-ignition engine technology is prompt catalyst warming. Emission mitigation largely does not occur while the catalyst is below its “light-off temperature”, which takes a certain time to achieve when the engine starts from a cold condition. If the catalyst takes too long to light-off, the vehicle could fail its emission certification; it is necessary to minimize the catalyst warm up period to mitigate emissions as quickly as possible. One technique used to minimize catalyst warm up is to calibrate the engine in such a way that it delivers high temperature exhaust. At idle or low speed/low-load conditions, this can be done by retarding spark timing with a corresponding increase in fuel flow rate and / or leaning the mixture. Both approaches, however, encounter limits as combustion stability degrades and / or nitrogen oxide emissions rise excessively.
Technical Paper

An Investigation into the Effect of Fuel Injection System Improvements on the Injection and Combustion of DiMethyl Ether in a Diesel Cycle Engine

For nearly twenty years, DiMethyl Ether has been known to be an outstanding fuel for combustion in diesel cycle engines. Not only does it have a high Cetane number, it burns absolutely soot free and produces lower NOx exhaust emissions than the equivalent diesel. However, the physical properties of DME such as its low viscosity, lubricity and bulk modulus have negative effects for the fuel injection system, which have both limited the achievable injection pressures to about 500 bar and DME's introduction into the market. To overcome some of these effects, a common rail fuel injection system was adapted to operate with DME and produce injection pressures of up to 1000 bar. To understand the effect of the high injection pressure, tests were carried out using 2D optically accessed nozzles. This allowed the impact of the high vapour pressure of DME on the onset of cavitation in the nozzle hole to be assessed and improve the flow characteristics.
Journal Article

Use of a Catalytic Stripper as an Alternative to the Original PMP Measurement Protocol

The Particle Measurement Programme (PMP) developed an exhaust particle number measurement protocol that has been adopted by current light duty vehicle emission regulations in Europe. This includes thermal treatment of the exhaust aerosol to isolate solid particles only and a number counting device with a lower cutpoint of 23 nm to avoid measurement of smaller particles that may affect the repeatability of the measurement. In this paper, we examine a potential alternative to the PMP system, where the thermal treatment is replaced by a catalytic stripper (CS). This offers oxidation and not just evaporation of the volatile components. Alternative sampling systems, either fulfilling the PMP recommendations or utilizing a CS, have been explored in terms of their volatile particle removal efficiency. Tests have been conducted on diesel exhaust, diesel equipped with DPF and gasoline direct injection emissions.
Technical Paper

Optimization of Hybrid Power Trains-Physical Based Modeling for Concept Design

This paper presents a comparison of a hybrid and a conventional powertrain using physical based simulation models on the system engineering level. The system engineering model comprises mechanistic sub-models of the internal combustion engine including exhaust aftertreatment devices, electric components, mechanical drivetrain, thermoregulation system and the corresponding controllers. Essential sub-models are discussed in detail and their interaction on the system level is pointed out. Special attention is paid to compile a real-time capable model by combining mean value air path and drivetrain models with a crank-angle resolved cylinder description and quasi-steady state considerations applied in electrical and cooling networks. A turbocharged gasoline direct injection engine is modeled and calibrated based on steady-state measurements. The conversion performance of a three way catalyst is compared to light-off measurements.
Technical Paper

MiL-Based Calibration and Validation of Diesel-ECU Models Using Emission and Fuel Consumption Prediction during Dynamic Warm-Up Tests (NEDC)

A calibration and validation workflow will be presented in this paper, which utilizes common static global models for fuel consumption, NOx and soot. Due to the applicability for warm-up tests, e. g. New European Driving Cycle (NEDC), the models need to predict the temperature influence and will be fitted with measuring data from a conditioned engine test bed. The applied model structure - consisting of a number of global data-based sub-models - is configured especially for the requirements of multi-injection strategies of common rail systems. Additionally common global models for several constant coolant water temperature levels are generated and the workflow tool supports the combination and segmentation of global nominal map with temperature correction maps for seamless and direct ECU setting.
Journal Article

xD+1D Catalyst Simulation-A Numerical Study on the Impact of Pore Diffusion

This paper presents a numerical study on the impact of washcoat diffusion on the overall conversion performance of catalytic converters. A comprehensive transient 1D pore diffusion reaction model is embedded in state-of-the-art 1D and 3D catalytic converter models. The pore diffusion model is discussed with its model equations and the applied diffusive transport approaches are summarized. The diffusion reaction model is validated with the help of two available analytical solutions. The impact of basic washcoat characteristics such as pore diameters or thickness on overall conversion performance is investigated by selected 1D+1D calculations. This model is also used to highlight the impact of boundary layer transfer, pore diffusion and reaction on the overall converter conversion performance. The interaction of pore diffusion and flow non-uniformities is demonstrated by 3D+1D CFD simulations.
Journal Article

Analysis of Thermodynamic Characteristics of Diesel Engine Emission Control Strategies Using a Multi-Zone Combustion Model

The paper describes a zero-dimensional crank angle resolved combustion model which was developed for the analysis and prediction of combustion in compression ignition (CI) engines. The model relies on the multi zone combustion model (MZCM) approach of Hiroyasu. The main sub-models were taken from literature and extended with additional features described in this paper. A special procedure described in a previous paper is used to identify the mechanisms of the combustion process on the basis of the measured cylinder pressure trace. Based on the identified mechanisms the present work concentrates on the analysis of the causal effects that predominantly control the combustion process and the formation of NOx and Soot. The focus lies on the changes of the thermodynamic states and the composition of the reaction zones caused by different emission control strategies.
Technical Paper

Real Time Capable Pollutant Formation and Exhaust Aftertreatment Modeling-HSDI Diesel Engine Simulation

Modern Diesel engines require an integrated development of combustion strategies, air management and exhaust aftertreatment. This study presents a comprehensive simulation approach with the aim to support engine development activities in the virtual environment. A real-time capable engine, vehicle and control model is extended by three key features. First, a pollutant production model is embedded in a two-zone cylinder model. Second, a framework for catalytic pollutant conversion is built focusing on modern diesel exhaust aftertreatment systems. Third, an extended species transport model is introduced considering the transport of pollutants through the air path. The entire plant model is validated on the example of a passenger car Diesel engine. The predicted engine behavior is compared with steady-state measurements. The NO formation model is investigated for a series of steady-state and transient operating conditions.
Technical Paper

Automatic ECU-Calibration - An Alternative to Conventional Methods

Due to increasing complexity of engine electronic systems, there is a demand to handle the often more than 10,000 calibration data automatically. Establishing optimized start of injection and EGR tables of a TC DI Diesel engine by conventional methods takes about two weeks of intensive calibration work. By automatic map calibration, this task can be handled in less than 20 hours automatically, with no staff required during optimization. The benefits of automatic calibration therefore are reduced costs and faster response to any changes in parameters, even with complex multidimensional engine calibration problems. The paper describes the optimization method as well as the experimental work on the test stand that produces the results.