Search Results

In recent years, the number of reported traffic accidents due to sudden deterioration in driver’s physical condition has been increasing, it is expected to develop a system that prevents accidents even if physical condition suddenly changes while driving, or reduces damage through vehicle body control. For this purpose, it is necessary to detect sudden changes of the driver’s physical condition, and research is being conducted widely. Among them, it is reported that some of such changes may appear in the heartbeat interval. In other words, by acquiring the driver’s heartbeat interval in real time, it may be possible to detect the sudden changes, and reduce traffic accident. Even if a traffic accident occurs, the damage can be reduced by emergency evacuation immediately after detecting sudden changes.

With the improved safety performance of vehicles, the number of accidents has been decreasing. However, accidents due to driver distraction still occur, which means that there is a high need to determine whether a driver is properly looking at the surroundings. Meanwhile, with the trend toward partial automatic driving of vehicles in recent years, it is also urgently required that the state of the driver be grasped. Even if automatic driving is not installed, it is desired that the state of the driver be grasped and an application for control be performed depending on the state of the driver. Under these circumstances, we have built an algorithm that determines of the direction a driver is looking, to make a basic determination of whether or not the driver is in a state suitable for safe driving of the vehicle.

This paper reports the results of a study into a preview control that uses the displacement of the road surface in front of the vehicle to improve for front and rear actuator responsiveness delays, as well as delays due to calculation, communication, and the like. This study also examined the effect of a preview control using the eActive3 electric active suspension system, which is capable of controlling the roll, pitch, and warp modes of vehicle motion.

It is well known that the self-aligning torque decreases before lateral force is saturated. Focusing on this self-aligning torque change, an estimation method has been developed to detect the friction condition between steered wheels and road surface before the lateral force reaches the friction limit. The lateral grip margin (LGM) is defined based on the self-aligning torque change, which is obtained using the EPS torque and motor current information. The LGM is theoretically analyzed based on the tire model and experimentally verified through the full-scale vehicle test. Moreover, the estimated LGM is applied for the chassis control systems to improve the vehicle dynamics performance.

Sport Utility Vehicles (SUV) and light duty trucks have gained in popularity for the last several years and the demand for more car-like behavior has increased, accordingly. Two areas for potential improvement are vehicle stability and maneuverability while parking. 4WS (4 wheel steering system) is known as an effective solution to stability and low speed maneuverability. In this paper, we identify a new systematic design method of two degree of freedom vehicle state feedback control algorithm that can improve vehicle stability, and show its control effects for a SUV with trailer towing. Low speed maneuvering is improved when the rear tires are steered in negative phase relative to the front tires. However with a large rear steer angle at low speed, the vehicle's rear overhang tracks a wider swing-out path than a 2WS vehicle. For this concern, we propose a new swing-out reduction control algorithm.

Switched Reluctance Motor (SRM) mainly has two advantageous characteristics such as no magnet and simple construction. These characteristics contribute lower cost and higher reliability compared with other motor systems such as brushless permanent magnet motors or induction motors. However, acoustic noise and output torque ripple should be improved when the SRM is applied to a traction system for passenger electric vehicle since these characteristics directly affect vehicle quietness and drivability. In this paper, we describe a system configuration of the SRM traction system for passenger electric vehicle. The SRM traction system includes an electric motor, transmission gears and power inverter module. Then, an approach to improve acoustic noise and output torque ripple is introduced. Generation mechanisms of acoustic noise and output torque ripple are analyzed.

This paper describes the investigation into the contact pressure and incidental deformation on the contact surface of the piston skirt which comes in contact with the cylinder bore in operation. Focused on the single piston static tests in the first place, relationship between the contact pressure on said skirt and the strains developed inside the skirt, and the relationship between the deformation of skirt face and the strains inside the skirt were studied. Then, the dynamic contact pressure onto the skirt in operation and the amount of deformation were calculated based on the relationships mentioned above using the factor of dynamic strains measured on an engine in operation. The deformation of skirt calculated using said dynamic strains was verified by the direct measurement of the skirt deformation. It was demonstrated that the thrust side of a piston skirt was largely deformed due to enlarged contact pressure caused by the piston slap subsequent to firing top dead center.

Rear steering system can improve vehicle stability using active control of the rear wheel angles. For designing the rear steering system, environmental conditions, performance deterioration due to aging and component variation as a result of manufacturing tolerance under mass production must be taken into consideration. We have applied two-degree-of-freedom (2DOF) feedback control with feedforward control for the motor servo control so that the rear steering actuator can track the target rear steering angle accurately and stably. The control system is designed based upon a nominal mathematical model and its variation range. As a result, the rear steering actuator can be controlled with excellent performance and high reliability. This paper describes the mathematical model construction in the frequency domain and a robust motor servo controller design based on 2DOF feedback control with feedforward control.

As a process that enables the high-speed and continuous forming of lengthy materials with a constant cross-sectional configuration, roll forming offers much higher productivity than the stamping process. However, in case a change must be made to the shape of the cross section, the material must normally be stamped or joined with a part containing a separate shape. This affects productivity, increases the number of pieces, and degrades the material's appearance. This report describes the roll-forming technology that we developed, in which the cross section of the material can be changed gradually. This method adopts a system which uses a movable and rotatable roll-stand that enables high-speed, continuous roll-forming processes.

Airflow effect is one of the important functions demanded of a rear spoiler. It helps prevent mud or dust from swirling up behind the running vehicle, or in the case of driving in the rain or snow, helps prevent rain or snow from adhering to the rear window. During the design process, we often decide on the shape of a spoiler in a relatively short time, focusing primarily on its appearance. Therefore, we established a design method using the recently developed computational fluid dynamics (CFD) to determine the central cross sectional shape of a spoiler that produces a desired airflow effect. We verified its effectiveness through testing.

Responsiveness is one of the main characteristics of a brake booster. The design of a tandem booster, with its two boosting chambers, has a negative influence on high responsiveness. This report, using the CFD method for the air flow analysis, shows the way we found the most suitable air passage within the space of the given design of the current production tandem booster.

In this paper, we discuss vehicle directional stability and introduce advanced stability control (ASTC) to stabilize the vehicle during severe cornering. Vehicle behavior in a transient steering condition during severe cornering was analyzed by computer simulation. It was found that applying an external yaw moment makes the vehicle more stable. The effect of controlling the brake force response is also evaluated by simulation to determine the brake actuator response criteria. The actual vehicle test was performed with a pylon slalom using a hydraulic brake actuator. It is verified that the ASTC stabilizes the vehicle for transient steering maneuvers.