Search Results

In recent years, the number of reported traffic accidents due to sudden deterioration in driver’s physical condition has been increasing, it is expected to develop a system that prevents accidents even if physical condition suddenly changes while driving, or reduces damage through vehicle body control. For this purpose, it is necessary to detect sudden changes of the driver’s physical condition, and research is being conducted widely. Among them, it is reported that some of such changes may appear in the heartbeat interval. In other words, by acquiring the driver’s heartbeat interval in real time, it may be possible to detect the sudden changes, and reduce traffic accident. Even if a traffic accident occurs, the damage can be reduced by emergency evacuation immediately after detecting sudden changes.

With the improved safety performance of vehicles, the number of accidents has been decreasing. However, accidents due to driver distraction still occur, which means that there is a high need to determine whether a driver is properly looking at the surroundings. Meanwhile, with the trend toward partial automatic driving of vehicles in recent years, it is also urgently required that the state of the driver be grasped. Even if automatic driving is not installed, it is desired that the state of the driver be grasped and an application for control be performed depending on the state of the driver. Under these circumstances, we have built an algorithm that determines of the direction a driver is looking, to make a basic determination of whether or not the driver is in a state suitable for safe driving of the vehicle.

Injury Risk Curves are developed from cadaver data for sternal deflections produced by anterior, distributed chest loads for a 25, 45, 55, 65 and 75 year-old Small Female, Mid-Size Male and Large Male based on the variations of bone strengths with age. These curves show that the risk of AIS ≥ 3 thoracic injury increases with the age of the person. This observation is consistent with NASS data of frontal accidents which shows that older unbelted drivers have a higher risk of AIS ≥ 3 chest injury than younger drivers.

In a system with which acceleration and braking by the driver are automated, a gap against the system can be felt when the timing of acceleration or deceleration is different from that intended by the driver or the extent of acceleration or deceleration exceeds an acceptable limit. For an automated system, it is important to realize a control that provides comfort and a sense of security for the driver. This paper is related to the technology that secures the ride comfort felt by the driver (comfort and a sense of security) within an appropriate range and presents a discussion of the technological means to improve the ride comfort from a viewpoint particularly related to longitudinal direction.

Recently, automobile features designed to improve maneuverability and convenience are being improved. However, many drivers still have difficulty with parking maneuvers. Although parking is unavoidable for drivers, yet ranks third among the most difficult driving situations for Japanese drivers. Drivers in other countries also consider parking to be difficult and even skill drivers would appreciate some assistance. Therefore, a parking support system has been developed to reduce the workload for all drivers while also improving parking performance. The parking support system Human-Machine Interface (HMI) operation should be designed to easy to use for best performance. The back-in perpendicular parking performance of drivers with different skill levels was studied to see the effect of the parking support system. Back-in perpendicular parking is the major parking method in Japan.

By adapting vehicle control systems to the skill level of the driver, the overall vehicle active safety provided to the driver can be further enhanced for the existing active vehicle controls, such as ABS, Traction Control, Vehicle Stability Enhancement Systems. As a follow-up to the feasibility study in [1], this paper provides some recent results on data-driven driving skill characterization. In particular, the paper presents an enhancement of discriminant features, the comparison of three different learning algorithms for recognizer design, and the performance enhancement with decision fusion. The paper concludes with the discussions of the experimental results and some of the future work.

This paper describes the methodology used to design and perform a CFD analysis of a Chevrolet Impala SS Funny Car body. This body was designed for the purpose of making it available for teams to race it in the National Hot Rod Association (NHRA) drag racing series beginning with the 2007 race season. Several challenges were presented in this project: (1) This was the first time a General Motors drag racing body for use in professional classes (Funny Car or otherwise) was ever designed in CAD. (2) The body was originally designed as a 2007 Chevrolet Monte Carlo. After the tooling was completed, changes in Chevrolet’s product lineup required that the body be changed to a 2007 Impala SS. (3) Budget constraints precluded CFD analysis until after the bodies were already being manufactured. There were several teams that raced the new body during the 2007 race season. One of these teams won the Funny Car Driver’s Championship.

The market growth for electric-hybrid passenger vehicles has been very significant and is expected to reach nearly 25% of all vehicles sold in the US by 2015. Hybrid commercial vehicles are also being developed by several OEM's. This paper discusses the progress of Delphi Thermal Systems in developing an integrated electric compressor drive with high cooling capacity (9 kW+), sufficient for large hybrid SUV's and commercial vehicles such as Class 8 tractors with sleeper. An important driver for use of the electric compressor in the hybrid truck application is the reduction of engine idling time while maintaining comfort in the cab or sleeper. Design details of a compact 5 kW SPM motor, its inverter drive, and issues related to its integration into the compressor housing are described. Test results are given confirming excellent performance.

A unified approach to collision warning due to in-lane and neighboring traffic is presented. It is based on the concept of velocity obstacles, and is designed to alert the driver of a potential front collision and against attempting a dangerous lane change maneuver. The velocity obstacle represents the set of the host velocities that would result in collision with the respective static or moving vehicle. Potential collisions are simply determined when the velocity vector of the host vehicle penetrates the velocity obstacle of a neighboring vehicle. The generality of the velocity obstacle and its simplicity make it an attractive alternative to competing warning algorithms, and a powerful tool for generating collision avoidance maneuvers. The velocity obstacle-based warning algorithm was successfully tested in simulations using real sensor data collected during the Automotive Collision Avoidance System Field Operational Test (ACAS FOT) [10].

This paper presents the new techniques/methods being used for the rapid vehicle development and system level performance assessment. It consists of two parts: the first part presents the automated multilevel substructuring (AMLS) technique, which greatly reduces the computational demands of larger finite element models with millions of degrees of freedom(DOF) and extends the capabilities to higher frequencies and higher level of accuracy; the second part is on the superelement in conjunction with the Component Mode Synthesis (CMS) and also Automated Component Mode Synthesis (ACMS) techniques. In superelement, a full vehicle model is divided into components such as Body-in-white, Front cradle/chassis, Rear cradle/chassis, Exhaust, Engine, Transmission, Driveline, Front suspension, Rear suspension, Brake, Seats, Instrument panel, Steering system, tires, etc. with each piece represented by reduced stiffness, mass, and damping matrices.

This paper presents the hybrid technique application in identifying the noise transfer paths and the force transmissibility between the interfaces of the different components in the vehicle. It is the stiffness based formulation and is being applied for the low to mid frequency range for the vibration and structure borne noise. The frequency response functions such as dynamic compliance, mobility, inertance, and acoustic sensitivity, employed in the hybrid method, can either be from the test data or finite element solution or both. The Source-Path-Receiver concept is used. The sources can be from the road surface, engine, transmission, transfer case, prop-shaft, differential, rotating components, chain drives, pumps, etc., and the receiver can be driver/passenger ears, steering column, seats, etc.

The main objective of this paper was to determine if the vehicle performance can be maintained with a reduced mass cradle structure. Aluminum and magnesium cradles were compared with the baseline steel cradle. First, the steel chassis alone is analyzed with the refined finite element model and validated with experimental test data for the frequencies, normal modes, stiffnesses and the drive-point mobilities at various attachment mount/bushing locations. The superelement method in conjunction with the component mode synthesis (CMS) technique was used for each component of the vehicle such as Body-In-White, Instrument Panel, Steering Column Housing & Wheel, Seats, Cradles, CRFM, etc. After assemblage of all the superelements, analysis was carried out by changing the front and rear cradle gauges and the material properties. The drive-point mobility response was computed at various locations and the noise (sound pressure) level was calculated at the driver and passenger ears.

A multi vector design tool to accurately predict instrument panel obscuration was developed to insure that critical legal displays in vehicles are not obscured. The concept provides for a computer generated light source shaped to replicate the human eyes. The light source is then projected onto a 3D math based arrangement and the resultant shadows are visible on the instrument panel surface and its displays. Design studios require criteria for the placement of the instrument cluster gages and displays, various controls, switches, and steering column stalks before an interior theme can be completed. Therefore, instrument panel obscuration and visibility must be determined early in the design process. The obscured areas are a function of the instrument panel surface, steering wheel rim, hub, spokes, and the location of the driver's eyes. This light source method allows engineers and designers the ability to quickly determine obscured areas.

Different countermeasure designs for reducing the HIC (d) and to comply with FMVSS201U have been evaluated in many component-level studies by suppliers and OEMs. This study presents guidelines to support future countermeasure and interior designs. FMVSS201U has changed the way OEMs design interiors of the vehicles today. Most recently, much more work is being done to find ways to design interiors of the vehicles that comply with FMVSS201U while keeping the interiors aesthetically pleasing, attaining driver comfort and meeting driver visibility requirements. Introduction of side-rail airbags has further affected countermeasure design and packaging. This study focuses on several countermeasure designs in the side-rail region as used in a mid-sized vehicle implemented to meet FMVSS201U requirements and their efficiency with respect to Head Injury Criterion (HIC) reduction given a fixed packaging space.

A newly developed parking assist system, which is based on rear view camera, is disclosed. System features include ‘parallel parking aid’ with voice guidance message along with several guidelines superimposed onto the rear view camera image. Voice guide message helps driver understand appropriate timing for each procedure of parallel parking. The system was designed to let driver follow the system by voice message rather than visual guide information through the screen for safety reason. The guide algorism is designed under ‘two turns’ parking maneuvers so that required longitudinal parking space becomes minimal. A key development of this system, which is to design the guide algorism to avoid collision to adjacent vehicle during parallel parking operation, is also discussed in this paper. User can select either ‘parallel guide’ or ‘normal (such as garage parking)’ mode through touch screen switch on display surface.

Forward collision warning (FCW) systems are intended to provide drivers with crash alerts to help them avoid or mitigate rear-end crashes. To facilitate successful deployment of FCW systems, the Ford-GM Crash Avoidance Metrics Partnership (CAMP) developed preliminary minimum functional requirements for FCW systems implemented on light vehicles (passenger cars, light trucks, and vans). This paper summarizes one aspect of the CAMP results: minimum requirements and recommendations for when to present rear-end crash alerts to the driver. These requirements are valid over a set of kinematic conditions that are described, and assume successful tracking and identification of a legitimate crash threat. The results are based on extensive closed-course human factors testing that studied drivers' last-second braking preferences and capabilities. The paper reviews the human factors testing, modeling of results, and the computation of FCW crash alert timing requirements and recommendations.

Development of a system which utilizes technology for the recognition of a vehicle's surroundings. Research is currently taking place in many countries, the goals of which are to improve a vehicle's safety and convenience by reducing driver strain through the automation of the recognition, judgment, and operation capabilities that are needed when driving an automobile. To recognize the vehicle's surroundings, we have adopted an image sensor system which offers superior three-dimensional recognition capabilities. In this paper, we will introduce a inter vehicle distance control system which controls the vehicle's throttle and braking functions by detecting the position of the driving lane and the distance to the vehicle in front based on the images obtained by a CCD camera.

In order to cope with the increases of the consciousness of safety driving and the aged drivers, AISIN SEIKI CO., LTD. and TOYOTA MOTOR CORPORATION have aimed at improvements in rear view visibility of outside mirrors running under the raining conditions (water cleaning), and have developed mirror with water cleaning device utilizing ultra sonic vibrations. The mirror was named as ULTRA SONIC VIBRATING MIRROR and have been installed with a TOYOTA flagship car “CELSIOR” corresponding to “LEXUS” sold in the U.S.

This study assesses the understanding and recognition, by U.S. drivers, of the 25 automotive ISO symbols specified in SAE Standard J1048. A two-part survey was administered to 505 volunteers at a Secretary of State's office located in a Detroit suburb. Percentage results for symbol understanding indicated low levels of understanding for many symbols; percentage results for symbol recognition were generally much higher for all symbols. The effects of gender, age, and education level on the percentage results are summarized.