Search Results

Expanding upon the authors’ previous work which utilized a GT-Power model of the Cooperative Fuels Research (CFR) engine under Research Octane Number (RON) conditions, this work defines the boundary conditions of the CFR engine under Motored Octane Number (MON) test conditions. The GT-Power model was validated against experimental CFR engine data for primary reference fuel (PRF) blends between 60 and 100 under standard MON conditions, defining the full range of interest of MON for gasoline-type fuels. The CFR engine model utilizes a predictive turbulent flame propagation sub-model, and a chemical kinetic solver for the end-gas chemistry. The validation was performed simultaneously for thermodynamic and chemical kinetic parameters to match in-cylinder pressure conditions, burn rate, and knock point prediction with experimental data, requiring only minor modifications to the flame propagation model from previous model iterations.

Additive manufacturing was used to fabricate a head for an automotive-scale single-cylinder engine operating on natural gas. The head was consisted of a bimetallic composition of stainless steel and bronze. The engine performance using the bimetallic head was compared against the stock cast iron head. The heads were tested at two speeds (1200 and 1800 rpm), two brake mean effective pressures (6 and 10 bar), and two equivalence ratios (0.7 and 1.0). The bimetallic head showed good durability over the test and produced equivalent efficiencies, exhaust temperatures, and heat rejection to the coolant to the stock head. Higher combustion temperatures and advanced combustion phasing resulted from use with the bimetallic head. The implication is that with optimization of the valve timing, an efficiency benefit may be realized with the bimetallic head.

The effect of charge rate was determined using constant-current (CC) and the USABC Fast-Charge (FC) tests on commercial lithium-ion cells. Charging at high rates caused performance decline in the cells. Representing the resistance data as ΔR vs. Rn-1 plots was shown to be a viable method to remove the ambiguity inherent in the time-based analyses of the data. Comparing the ΔR vs. Rn-1 results, the change in resistance was proportional to charge rate in both the CC and FC cell data, with the FC cells displaying a greater rate of change. Changes, such as delamination, at the anode were seen in both CC and FC cells. The amount of delamination was proportional to charge rate in the CC cells. No analogous trend was seen in the FC cells; extensive delamination was seen in all cases. These changes may be due to the interaction of processes, such as lithium plating and i2R heating.

Cavitation plays a significant role in high pressure diesel injectors. However, cavitation is difficult to measure under realistic conditions. X-ray phase contrast imaging has been used in the past to study the internal geometry of fuel injectors and the structure of diesel sprays. In this paper we extend the technique to make in-situ measurements of cavitation inside unmodified diesel injectors at pressures of up to 1200 bar through the steel nozzle wall. A cerium contrast agent was added to a diesel surrogate, and the changes in x-ray intensity caused by changes in the fluid density due to cavitation were measured. Without the need to modify the injector for optical access, realistic injection and ambient pressures can be obtained and the effects of realistic nozzle geometries can be investigated. A range of single and multi-hole injectors were studied, both sharp-edged and hydro-ground. Cavitation was observed to increase with higher rail pressures.

Lignin by-products from biorefineries has the potential to provide a low-cost alternative to petroleum-based precursors to manufacture carbon fiber, which can be combined with a binding matrix to produce a structural material with much greater specific strength and specific stiffness than conventional materials such as steel and aluminum. The market for carbon fiber is universally projected to grow exponentially to fill the needs of clean energy technologies such as wind turbines and to improve the fuel economies in vehicles through lightweighting. In addition to cellulosic biofuel production, lignin-based carbon fiber production coupled with biorefineries may provide $2,400 to $3,600 added value dry Mg−1 of biomass for vehicle applications. Compared to producing ethanol alone, the addition of lignin-derived carbon fiber could increase biorefinery gross revenue by 30% to 300%.

In an earlier paper, the authors described how Model-Based System Engineering could be utilized to provide a virtual Hardware-in-the-Loop simulation capability, which creates a framework for the development of virtual ECU software by providing a platform upon which embedded control algorithms may be developed, tested, updated, and validated. The development of virtual ECU software is increasingly valuable in automotive control system engineering because vehicle systems are becoming more complex and tightly integrated, which requires that interactions between subsystems be evaluated during the design process. Variational analysis and robustness studies are also important and become more difficult to perform with real hardware as system complexity increases. The methodology described in this paper permits algorithm development to be performed prior to the availability of vehicle and control system hardware by providing what is essentially a virtual integration vehicle.

As batteries become a major component of numerous advanced vehicles, significant efforts have been allocated towards characterizing and estimating battery energy capability over the lifetime of a vehicle. Currently, battery State of Charge (SOC) is one of the primary values used for this characterization; however SOC usage has several issues when implemented in Electric Vehicle (EV), Hybrid Electric Vehicle (HEV), and Plug-In Hybrid Electric Vehicle (PHEV) systems. One of the main issues with reporting battery SOC as a characterization of battery energy capability is that it only gives a percentage of the energy available to the operator. SOC does not accurately represent the true capability or capacity of the battery, and thus fails to account for the impact to capability with respect to battery size, age, and recent operational history.

Over 250 million vehicles are operating on United States roads and highways and over 12 million of them reach the end of their useful lives annually. These end-of-life vehicles (ELVs) contain over 24 million tons (21.8 million metric tonnes) of materials including ferrous and non-ferrous metals, polymers, glass, and automotive fluids. They also contain many parts and components that are still useable and some that could be economically rebuilt or remanufactured. Dismantlers acquire the ELVs and recover from them parts for resale “as-is” or after remanufacturing. The dismantler then sells what remains of the vehicle, the “hulk”, to a shredder who shreds it to recover and sell the metals. Presently, the remaining non-metallic materials, commonly known as shredder residue, are mostly landfilled. The vehicle manufacturers, now more than ever, are working hard to build more energy efficient and safer, more affordable vehicles.

Model-based control system design improves quality, shortens development time, lowers engineering cost, and reduces rework. Evaluating a control system's performance, functionality, and robustness in a simulation environment avoids the time and expense of developing hardware and software for each design iteration. Simulating the performance of a design can be straightforward (though sometimes tedious, depending on the complexity of the system being developed) with mathematical models for the hardware components of the system (plant models) and control algorithms for embedded controllers. This paper describes a software tool and a methodology that not only allows a complete system simulation to be performed early in the product design cycle, but also greatly facilitates the construction of the model by automatically connecting the components and subsystems that comprise it.

Plug-in hybrid electric vehicle (PHEV) technologies have the potential for considerable petroleum consumption reductions, possibly at the expense of increased tailpipe emissions due to multiple “cold” start events and improper use of the engine for PHEV specific operation. PHEVs operate predominantly as electric vehicles (EVs) with intermittent assist from the engine during high power demands. As a consequence, the engine can be subjected to multiple cold start events. These cold start events may have a significant impact on the tailpipe emissions due to degraded catalyst performance and starting the engine under less than ideal conditions. On current hybrid electric vehicles (HEVs), the first cold start of the engine dictates whether or not the vehicle will pass federal emissions tests. PHEV operation compounds this problem due to infrequent, multiple engine cold starts.

This paper covers the development of a closed loop transaxle synchronization algorithm which was a key deliverable in the control system design for the L3 Enigma, a Battery Dominant Hybrid Electric Vehicle. Background information is provided to help the reader understand the history that lead to this unique solution of the input and output shaft synchronizing that typically takes place in a manual vehicle transmission or transaxle when shifting into a gear from another or into a gear from neutral when at speed. The algorithm stability is discussed as it applies to system stability and how stability impacts the speed at which a shift can take place. Results are simulated in The MathWorks Simulink programming environment and show how traction motor technology can be used to efficiently solve what is often a machine design issue. The vehicle test bed to which this research is applied is a parallel biodiesel hybrid electric vehicle called the Enigma.

Many of today's automotive control system simulation tools are suitable for simulation, but they provide rather limited support for model building and management. Setting up a simulation model requires more than writing down state equations and running them on a computer. The role of a model library is to manage the models of physical components of the system and allow users to share and easily reuse them. In this paper, we describe how modern software techniques can be used to support modeling and design activities; the objective is to provide better system models in less time by assembling these system models in a “plug-and-play” architecture. With the introduction of hybrid electric vehicles, the number of components that can populate a model has increased considerably, and more components translate into more possible drivetrain configurations. To address these needs, we explain how users can simulate a large number of drivetrain configurations.

A sustainable activity is one that is economically attractive, environmentally friendly and provides a beneficial service to society in a safe and responsible manner. Having a sustainable operation is a target that today’s industries are striving to attain. The automotive industry and its products are major users of natural resources and a source of greenhouse emissions. In order to reduce its energy consumption and greenhouse emissions the industry is using more lightweighting materials in manufacturing its products. These materials include polymers, composites, aluminum and magnesium. The increased interest in hybrid vehicles will increase the need for new materials such as lithium, cobalt and nickel. At the same time, regulations are calling for recycling more of the obsolete vehicles. Replacing the steel, which is recyclable, with lighter materials will result in a reduction in the recycling rate of vehicles unless the lightweighting materials are recycled.

Microstructure level inhomogeneities between the harder martensite phase and the softer ferrite phase render the dual phase (DP) steels more complicated failure mechanisms and associated failure modes compared to the conventionally used low alloy homogenous steels. This paper examines the failure mode DP780 steel under different loading conditions using finite element analyses on the microstructure levels. Micro-mechanics analyses based on the actual microstructures of DP steel are performed. The two-dimensional microstructure of DP steel was recorded by scanning electron microscopy (SEM). The plastic work hardening properties of the ferrite phase was determined by the synchrotron-based high-energy X-ray diffraction technique. The work hardening properties of the martensite phase were calibrated and determined based on the uniaxial tensile test results. Under different loading conditions, different failure modes are predicted in the form of plastic strain localization.

The process of shredding end-of-life vehicles to recover metals results in a byproduct commonly referred to as shredder residue. The four and a half million metric tons of shredder residue produced annually in the United States is presently land filled. To meet the challenges of automotive materials recycling, the U.S. Department of Energy is supporting research at Argonne National Laboratory in cooperation with the Vehicle Recycling Partnership (VRP) of the United States Council for Automotive Research (USCAR) and the American Plastics Council. This paper presents the results of a study that was conducted by Argonne to determine variations in the composition of shredder residue from different shredders. Over 90 metric tons of shredder residues were processed through the Argonne pilot plant. The contents of the various separated streams were quantitatively analyzed to determine their composition and to identify materials that should be targeted for recovery.

Recovering metals from obsolete automobiles, home appliances, and other metal-containing obsolete durables and other scrap involves shredding these objects and separating the reusable metals from the shredded material by using magnets, eddy current separators, and metal detectors. Over 12 million automobiles are shredded annually in the United States alone, and almost all of the 4.5 million metric tonnes (5 million short tons) of the shredder residue produced in the United States annually is disposed of in landfills. Over 13.6 million tonnes (15 million tons) of shredder residue is generated worldwide every year. The rise in disposal costs is further exacerbated in that the percentage of shredder residue that must be disposed of, in comparison with the percentage of marketable recovered metals, is increasing because of the increasing content of polymers in automobiles and in home appliances.

As part of an ongoing vehicle benchmarking effort at Argonne National Laboratory, four different power-split HEVs were tested on a chassis dynamometer to analyze their operational behavior and understand the control strategy and its relationship to the individual features of the vehicles tested. The controls that select the way in which engine operation matches best engine efficiency load points appears to have evolved From the Gen 1 to the Gen 2 Toyota Prius. The Ford Escape HEV and Lexus RX400h were also analyzed by using similar methods, although the data are not as extensive as those for the Prius hybrids. Whereas the Escape HEV appeared to operate in a manner similar to that of the Gen 1 Prius, the RX400h (with its relatively large engine) loads the engine with excess battery charge to keep it operating at higher power levels - apparently to improve overall efficiency.

The addition of metal nanoparticles to standard coolant fluids dramatically increases the thermal conductivity of the liquid. The properties of the prepared nanofluids will allow for lighter, smaller, and higher efficiency spacecraft thermal control systems to be developed. Nanofluids with spherical or rod-shaped metal nanoparticles were investigated. At a volume concentration of 0.5%, the room temperature thermal conductivity of a 2 nm spherical gold nanoparticle-water solution was increased by more than 10% over water alone. Silver nanorods increased the thermal conductivity of ethylene glycol by 53% and water by 26%.

Propagation-based and phase-enhanced x-ray imaging was developed as a unique metrology technique to visualize the internal structure of high-pressure fuel injection nozzles. We have visualized the microstructures inside 200-μm fuel injection nozzles in a 3-mm-thick steel housing using this novel technique. Furthermore, this new x-ray-based metrology technique has been used to directly study the highly transient needle motion in the nozzles in situ and in real-time, which is virtually impossible by any other means. The needle motion has been shown to have the most direct effect on the fuel jet structure and spray formation immediately outside of the nozzle. In addition, the spray cone-angle has been perfectly correlated with the numerically simulated fuel flow inside the nozzle due to the transient nature of the needle during the injection.

Argonne National Laboratory (ANL) researchers have embarked on an ambitious program to quantitatively demonstrate the potential of hydrogen as a fuel for internal combustion engines (ICEs) in hybrid-electric vehicle applications. In this initiative, ANL researchers need to investigate different hybrid configurations, different levels of hybridization, and different control strategies to evaluate their impacts on the potential of hydrogen ICEs in a hybrid system. Because of limitations in the choice of motor and battery hardware, a common practice is to fix the size of the battery and motor, depending on the hybrid configuration (starter/alternator, mild hybrid, or full hybrid) and to tune the system control for the above-available electrical power/energy. ANL has developed a unique, flexible, Hardware-In-the-Loop (HIL) platform for advanced powertrain technology evaluation: The Mobile Advanced Technology Testbed (MATT).