Search Results

The Environmental Protection Agency (EPA) recently tested a clean diesel fuel developed by Dion & Sons for use in stationary sources. This fuel is known as Amber 363 in Southern California and its technology is licensed outside of the Southern California area to Shell Oil Products Company for use as a stationary source fuel. The fuel, hereafter referred to as “Shell LOW NOX Fuel,” was tested in a 1990 model year heavy heavy-duty diesel engine using both the transient Federal Test Procedure (FTP) for on-highway heavy-duty engines, the steady-state FTP for nonroad heavy-duty engines, and the steady-state generator set test cycle. For each test, EPA measured hydrocarbon (HC), carbon monoxide (CO), nitrogen oxides (NOx) and particulate matter (PM) emissions. Transient testing showed that the Shell LOW NOX Fuel lowers NOx, HC and PM emissions with no statistically significant change in CO emissions for both cold-starts and hot-starts when compared to diesel certification test fuel.

A vehicle test program was conducted at the Environmental Protection Agency's National Vehicle and Fuel Emissions Laboratory to provide data on the relationship between fuel properties and exhaust emissions of nonmethane hydrocarbons (NMHC), NOx, and CO. This study, Phase III, is the third in a series of programs sponsored by the Agency. This Phase III program consisted of 19 light-duty high and normal emitting vehicles tested on 10 different fuels. The properties for each test fuel were specified in order to examine seven separate fuel effects on exhaust emissions; interactions between olefins and volatility, interactions between olefins and sulfur, very high and very low levels of sulfur, low levels of aromatics, low volatility, and low levels of olefins. For all of the fuels tested, the normal emitter vehicles produced greater percentage reductions than the high emitters. The data in this work showed lower NMHC emission reduction than predicted by the complex model.

Ten post-1981 and pre-1990 vehicles were tested to determine if the effect of gasoline reformulation would be different than predicted by the EPA complex model. All vehicles passed the IM-240 screening before fuel testing. A nonoxygenated baseline and four oxygenated test fuels with varying levels of sulfur and RVP were tested for exhaust emissions. The emission response of the fuel changes with these vehicles was similar to that predicted by the complex model. However, the NOx emissions of the vehicles in this study were less sensitive to sulfur level than complex model predicts. Also, the oxygenated reformulated gasolines regardless of sulfur level produced greater reductions in NMHC emissions than predicted by the complex model.

This paper reports the results of an exhaust emissions characterization from the non-catalyst control systems employed on the Mazda RX-4 rotary, the Honda CVCC, and the Chrysler electronic lean burn. Throughout the paper, exhaust emissions from these vehicles are compared to those from a Chrysler equipped with an oxidation catalyst and an air pump. The emissions characterized are carbon monoxide, hydrocarbons, nitrogen oxides, sulfur dioxide, sulfates, hydrogen sulfide, carbonyl sulfide, hydrogen cyanide, aldehydes, particulate matter, and detailed hydrocarbons. A brief description of the sampling and analysis procedures used is included within the discussion.

This report describes the results of a surveillance study initiated by the U.S. Environmental Protection Agency to measure gaseous exhaust emissions from 1020 light-duty motor vehicles. This project was the second effort in a continuing program using the CVS Federal Test Procedure. Selected privately-owned vehicles, drawn randomly from six metropolitan areas, were tested in as-received condition. The emissions data obtained from these 1966-1972 model-year vehicles are reported in grams per mile of unburned hydrocarbons, carbon monoxide, carbon dioxide and oxides of nitrogen while fuel economy is reported in mpg as determined over the Federal Driving Schedule.

A mathematical model of an automobile's emission rate is described. This model can be used to calculate the amounts of hydrocarbons, carbon monoxide, and oxides of nitrogen emitted by individual or groups of automobiles being driven over any known driving sequence. The development of the model requires the amounts of three pollutants given off by individual automobiles over short duration driving sequences (modes). The validity of the model is investigated by using it to calculate the amounts of each pollutant given off by individual automobiles over the hot transient portion (first 505 s) of the Federal Test Procedure driving sequence. These predicted emissions are then compared with observed amounts emitted from each automobile. Further, the ability of the model to predict emissions is investigated in light of the reproducibility of actual automobile emissions measured in replicated tests. These analyses indicate that the model performs extremely well.

A program was conducted to determine the effect of temperature and humidity on exhaust emissions from automotive engines. The objective was to determine if the effects were of sufficient magnitude to require the application of correction factors to measured exhaust emissions to standard humidity and temperature values. Both American and foreign-made vehicles were tested at 20 combinations of ambient temperature and humidity. The effect of temperature and humidity was found to be both unpredictable and of little significance for hydrocarbon and carbon monoxide emissions. No correction factors were developed for these exhaust gas constituents. The effect of temperature was found to be of little significance for oxides of nitrogen. However, humidity effects were found to be significant and predictable for oxides of nitrogen.