Search Results

Emissions regulations for 2007 will likely require engine manufacturers to use a diesel particulate filter (DPF) to meet particulate matter (PM) emission requirements. With the lower operating temperatures of light-duty diesel engines, some form of catalyst will be required to facilitate oxidation of accumulated soot PM to regenerate the DPF. This catalyst can either be permanently applied to the filter substrate in the manufacturing process, or be continuously delivered via the diesel fuel. In this study we examined the impact of using both forms of catalyst. A recently published study of the fuel-borne catalyst additive MMT [1] (Methylcyclopentadienyl Manganese Tricarbonyl), reviewed the performance of MMT in conjunction with an uncatalyzed DPF [2].

In July 2002, the Alliance of Automobile Manufacturers, the Association of International Automobile Manufacturers and the Canadian Vehicle Manufacturers Association released the results of a 6-year, two-part vehicle fleet test program to determine the effects of methyl-cyclopentadienyl manganese tricarbonyl (MMT®*) on vehicles equipped with state of the art emission control systems. Analysis of the data reports from this study shows that all of the vehicles met applicable emission standards, even though the fleet accumulated mileage under very severe conditions that accelerate degradation of vehicle emission control systems in excess of that expected from actual vehicle mileage. The study also demonstrated that gasoline-containing MMT had no adverse impact on vehicular emission control equipment.

SAE Paper 2002-01-2894 entitled, “The Impact of MMT Gasoline Additive on Exhaust Emissions and Fuel Economy of Low Emission Vehicles (LEV)” presents discussion and conclusions concerning the emissions from vehicles that accumulated mileage on gasoline with and without the fuel additive, methylcyclopentadienyl manganese tricarbonyl (or MMT®). Although the authors of the paper express concern about use of MMT®, the data on which the authors rely are consistent with the results and conclusions from prior evaluations of MMT® which have found that MMT® is compatible with effective emission control system operation (1,2,3). All vehicles tested in the study met the emission standards for all pollutants that apply to the test vehicles in-use and analysis of the data show MMT® had no effect on fuel economy.

This oil category was driven by two new cooled exhaust gas recirculation (EGR) engine tests operating with 15% EGR, with used oil soot levels at the end of the test ranging from 6 to 9%. These tests are the Mack T-10 and Cummins M11 EGR, which address ring, cylinder liner, bearing, and valve train wear; filter plugging, and sludge. In addition to these two new EGR tests, there is a Caterpillar single-cylinder test without EGR which measures piston deposits and oil consumption control using an articulated piston. This test is called the Caterpillar 1R and is included in the existing Global DHD-1 specification. In total, the API CI-4 category includes eight fired-engine tests and seven bench tests covering all the engine oil parameters. The new bench tests include a seal compatibility test for fresh oils and a low temperature pumpability test for used oils containing 5% soot. This paper provides a review of the all the tests, matrix results, and limits for this new oil category.

The long-term durability of a vehicle's exhaust catalyst is essential for emission control. Catalyst durability can be affected by a variety of factors including engine oil consumption. During normal engine operation, some of the lubricating oil is combusted. The deposition of combustion products from phosphorus containing lubricant additives on the catalyst can adversely affect catalyst durability. In an attempt to minimize the impact of oil consumption on additive performance, engines have been designed to reduce oil consumption and oils are being formulated with lower concentrations of phosphorus compounds. However, these phosphorus compounds protect the engine from excessive wear and cannot be easily removed from lubricant oil due to concerns over engine durability. The use of a phosphorus scavenger is an approach that works together with engine design to minimize catalyst deterioration.

The Clean Air Act of 1990 requires on-board diagnostics (OED) capabilities on all new vehicles. These diagnostic systems monitor the performance of engine and emission system components and inform the vehicle operator when component or system degradation could significantly impact emissions. Acceptable operation of the monitor requires proper treatment of system variables. Fuel composition is one of many possible variables that must be considered for monitoring components directly in the exhaust stream. Recently, the octane enhancing, emissions reducing additive methylcyclopentadienyl manganese tricarbonyl (MMT) was reintroduced into unleaded gasoline in the U.S. Prior to reintroduction, the additive underwent extensive testing to demonstrate that use of MMT does not adversely affect vehicle emissions or the operation of emission systems such as OBD. However, questions have been raised about the influence of the additive on OBD systems.

Extensive vehicle fleet testing has demonstrated that use of MMT can reduce net tailpipe out emissions. The use of fuel containing the octane-enhancing, emission-reducing fuel additive leads to manganese oxide deposits in the vehicle exhaust system. Studies of the physical and chemical effects of manganese oxide deposits on the performance of catalytic converters conclusively demonstrated that MMT does not adversely affect catalytic converters and, in fact, protected the converters from phosphorus and zinc. Despite the overwhelming evidence that MMT is compatible with catalytic converters and vehicle emission control systems, concerns have recently been raised about the effect of manganese oxides on OBD-II catalytic converter monitoring.

In designing fuel economy oils, two useful approaches are reduction of viscosity and incorporation of friction reducers. To achieve viscosity reduction without incurring problems of high oil consumption and possible interference with catalyst or oxygen sensor performance, the use of part-synthetic lubricants can be helpful. In this way, oil volatility (therefore oil consumption) is reduced and fuel economy is improved without incurring engine operating penalties. Friction reducers also can be used to improve fuel economy. The combination of these approaches furnishes the benefits of both. Laboratory and road testing of such combinations show important fuel economy benefits in normal vehicle operation, greater than those achievable from either approach alone. In addition, all other engine performance requirements are completely met. This advance in engine oil formulation technology, which opens up new possibilities to both vehicle manufacturers and consumers, is being further pursued.

Several makes and models of cars were modified for lean-burn operation using the Turbulent Flow Manifold (TFM), a unique intake manifold that provides improved preparation and distribution of the fuel-air mixture. Operation of the TFM is described, and exhaust emissions and fuel economy data are presented for the various cars. Exhaust port liners and thermal reactors were shown to be effective devices for reducing emissions from the basic lean-burn system. One car equipped with the TFM, port liners, and reactors was operated for 50,000 miles on an EPA-type durability test and had emissions well below the 1975 standards for California. Emissions, fuel economy, and durability data are presented.

This paper describes a method for accurately measuring sulfur oxides in automotive exhaust. In this method, the exhaust from a car is diluted with ambient air, then introduced into a large bag filled with clean dry air. The temperature, pressure, and humidity of the diluted exhaust are measured, along with the concentrations of hydrocarbons, carbon monoxide, carbon dioxide, SO2, and sulfates. Bag concentrations are related to the exhaust by using the sulfur/carbon ratio of the fuel. Established instrumental methods are used for the carbon compounds. The sulfur dioxide in the diluted exhaust gas is measured by the West-Gaeke method, which involves collecting a gaseous sample in a scrubber containing potassium tetrachloromecurate. The sulfates are collected on a particulate filter and measured by a new colorimetric method. The techniques we have developed have been applied to both non-catalyst and catalyst-equipped cars. These studies have shown that: 1.

MMT (methylcyclopentadienyl manganese tricarbonyl) is an antiknock additive for unleaded gasoline, which is now required for cars equipped with catalytic converters. Because of its effectiveness, MMT is economically attractive compared with achieving antiknock quality by refinery processing. Use of MMT in gasoline at a concentration of 0.125 g of contained manganese per gallon provides, on the average, about 2 road octane numbers. Compared to processing, this could represent a savings in crude oil of about 1%. Like other antiknocks, the economic attractiveness of MMT is greatest at low concentrations. Extensive road and dynamometer engine tests have shown that use of MMT in the recommended concentration range is compatible with general aspects of car operation--octane number requirement, exhaust valve and spark plug durability, and exhaust gas recycle for NOx control. Moreover, beneficial effects in exhaust valve guide and seat wear have been observed with MMT in some tests.