Search Results

In this paper, a control strategy for state of charge (SOC) allocation using navigation data for Hybrid Electric Vehicle (HEV) propulsion systems is proposed. This algorithm dynamically defines and adjusts a SOC target as a function of distance travelled on-line, thereby enabling proactive management of the energy store in the battery. The proposed approach incorporates variances in road resistance and adheres to geolocation constraints, including ultra-low emission zones (uLEZ). The anticipated advantages are particularly pronounced during scenarios involving extensive medium-to-long journeys characterized by abrupt topological changes or the necessity for exclusive electric vehicle (EV) mode operation. This novel solution stands to significantly enhance both drivability and fuel economy outcomes.

Many chassis and powertrain components in the transportation and automotive industry experience multi-axial cyclic service loading. A thorough load-history leading to durability damage should be considered in the early vehicle production steps. The key feature of rubber fatigue analysis discussed in this study is how to define local critical location strain time history based on nominal and complex load time histories. Material coupon characterization used here is the crack growth approach, based on fracture mechanics parameters. This methodology was utilized and presented for a truck engine mount. Temperature effects are not considered since proving ground (PG) loads are generated under isothermal high temperature and low frequency conditions without high amounts of self-heating.

Vibration shaker testing is a great tool of validating the vibration fatigue performance of automotive components & systems. However, the representative vibration schedule requires a pre-knowledge of the acceleration history for the test object, which usually is not available until the later development phase of a vehicle program when physical properties are available. Sometimes, a generic vibration schedule developed from the worst-case loading profiles are used with risk of lacking correlation with later full vehicle durability test such as Road Test Simulator (RTS) or Proving Ground (PG) road test due to the higher loading amplitude. This paper proposes a virtual accelerometer approach to collect acceleration responses of a component from a virtual vehicle model. First, a multiple body dynamic model will be produced for virtual load calculation over a series of digitalized virtual proving ground road profiles.

As more electric vehicles (BEV, HEV, PHEV, etc.) are adopted in the upcoming decades, it is becoming increasingly important to conduct vehicle-level thermal simulations under different drive-cycle conditions while incorporating the various subsystem thermal losses. Thermal management of the various heat sources in the vehicle is essential both in terms of ensuring passenger safety as well as maintaining all the subsystems within their corresponding safe temperature limits. It is also imperative that these thermal simulations include energy consumption prediction, while considering the effect of battery degradation both in terms of increased thermal losses as well as reduction in the vehicle’s range. For this purpose, a three-dimensional transient thermal analysis framework was coupled with an electrochemical P2D-based battery model and a vehicle dynamics model to test different scenarios and their effect on a hybrid vehicle’s range and the lithium-ion battery life.

In a passenger car, suspension link bushings, engine and transmission mount bushings and bump-stops are made of elastomeric materials, to maximize the durability and comfort. Thus, deformation behavior of rubber and its durability is important for product design and development. In virtual engineering, simulating rubber fatigue is a complex exercise, since it needs right modeling strategy and coupon based testing material data. Principal stretches based Ogden model is used to characterize the hyper elastic deformation behavior of natural rubber. Fatigue crack growth approach used here for the fatigue analysis. Engine torque strut mount is used to control the engine and transmission fore aft motion and it is connected between body and Powertrain (PT) system. Powertrain events are predominant for damage contribution to mount failure. So, it is important to predict fatigue life of mount elastomer bushing under Powertrain loading.

Fasteners, commonly used in automotive industry, play an important role in the safety and reliability of the vehicle structural system. In practical application, bolted joints would never undergo fully reversed loading; there always will be positive mean stress on bolt. The mean stress has little influence on the fatigue life if the maximum stress is lower than a threshold which is near the yield stress of the bolt. However, when the sum of the mean stress and the stress amplitude exceeds the threshold, the endurance limit stress amplitude decreases fast as the mean stress increases. The purpose of this paper is to research the fatigue endurance limit of a fastener and establish the threshold for safe design in automotive application. In order to obtain the fatigue endurance limit at different mean stress levels, various mechanical tests were performed on M12x1.75 and M16x1.5 Class 10.9 fasteners using MTS test systems.

Stringent requirements for high fuel economy and energy efficiency mandate using increasingly complex vehicle thermal systems in most types of electrified vehicles (xEVs). Enabling the maximum benefits of such complex thermal systems under the full envelope of their operating modes demands designing complex thermal control systems. This is becoming one of the most challenging problems for electrified vehicles. Typically, the thermal systems of such vehicles have several modes of operation, constituting nonlinear multiple-input/multiple-output (MIMO) dynamic systems that cannot be efficiently controlled using classical or rule based strategies. This paper covers the different steps towards the design of a model-based control (MBC) strategy that can improve the overall performance of xEV thermal control systems. To achieve the above objective, the latter MBC strategy is applied to control cooling of the cabin and high voltage battery.

Strength and fatigue assessment of chassis components are essentially influenced by the material used and manufacturing processes chosen. The manufacturing process of chassis components decides the variation in the mechanical properties of the component, which has an impact on the strength/fatigue performance. Investigating the design concerning the manufacturing processes is vital to the industry. Standard computer aided engineering (CAE) procedures for validating the alloy wheels usually consider the material properties as homogeneous. There was a gap between test results and CAE durability prediction (as per standard procedure). Incorporating the manufacturing process related characteristics with the strength simulation will be a viable solution to reduce this gap. This study was intended at developing a procedure for the strength analysis of an alloy wheel by considering the manufacturing process.

This paper will focus on automotive development highlights of FCA US LLC magnesium intensive closures components. Deploying lightweight materials is one of many key strategies that has been implemented to reduce vehicle mass and improve overall fuel economy while maintaining rigorous functional objective performance. This paper will outline some basic design and manufacturing considerations for magnesium closures. The development of the 2017 Chrysler Pacifica liftgate and 2018 Jeep® Wrangler swing gate along with the two generations of magnesium spare tire brackets will be the focus.

One of the advantages of hybrid vehicles is the ability to operate the engine more optimally at a low brake specific fuel consumption (BSFC) as compared to conventional vehicles. This ability of hybrid vehicles is a major factor contributing to the fuel economy improvement over conventional vehicles. Unlike conventional gasoline powertrains, hybrid powertrains allow engine to be switched off and use battery power to propel vehicles. In order to maintain battery state of charge neutral operation between the start and end of a drive cycle, the net electrical energy consumption from the battery requires to be zero. An optimization algorithm can be developed and calibrated in different ways to achieve net zero battery energy over the cycle. For instance, the engine can be operated at powers higher than the power of the drive cycle to charge the battery. This accumulated energy can be used for all-electric propulsion by turning off the engine.

In response to demands for higher fuel economy and stringent emission regulations, OEMs always strive hard to improve component/system efficiency and minimize losses. In the driveline system, improving the efficiency of an automotive rear-axle is critical because it is one of the major power-loss contributor. Optimum oil-fill inside an axle is one of the feasible solutions to minimize spin losses, while ensuring lubrication performance and heat-dissipation requirements. Thus, prior to conducting vehicle development tests, several dyno-level tests are conducted to study the thermal behavior of axle-oil (optimum level) under severe operating conditions. These test conditions represent the axle operation in hot weather conditions, steep grade, maximum tow capacity, etc. It is important to ensure that oil does not exceed its thermal limits (disintegration of oil leading to degradation).

Rapid Compression Machines (RCM) offer the ability to easily change the compression ratio and the pressure/mixture composition/temperature to gather ignition delay data at various engine relevant conditions. Therefore, RCMs with optical access to the combustion chamber can provide an effective way to analyze macroscopic spray characteristics needed to understand the spray injection process and for spray model development, validation and calibration at conditions that are suitable for engines. Fuel surrogates can help control fuel parameters, develop models for spray and combustion, and perform laser diagnostics with known fluorescence characteristics. This study quantifies and evaluates the macroscopic spray characteristics of multicomponent gasoline surrogates in comparison to their gasoline counterparts, under gasoline direct injection (GDI) engine conditions.

In this work autoignition delay times of two multi-component surrogates (high and low RON) were experimentally compared with their target full blend gasoline fuels. The study was conducted in a rapid compression machine (RCM) test facility and a direct test chamber (DTC) charge preparation approach was used for mixture preparation. Experiments were carried over the temperature range of 650K-900K and at 10 bar and 20 bar compressed pressure conditions for equivalence ratios of (Φ =) 0.6-1.3. Dilution in the reactant mixture was varied from 0% to 30% CO2 (by mass), with the O2:N2 mole ratio fixed at 1:3.76. This dilution strategy emulates exhaust gas recirculation (EGR) substitution in spark ignition (SI) engines. The multicomponent surrogate captured the reactivity trends of the gasoline-air mixtures reasonably well in comparison to the single component (iso-octane) surrogate.

The heat generated by an internal combustion engine must be dissipated to maintain acceptable component temperatures throughout the entire powertrain system under all operating conditions. However, under cold start conditions it is beneficial to retain this available heat to achieve faster warm-up in order to reduce fuel consumption. In modern engines there are several components in the coolant circuit that are used to accelerate the warm-up of sub-system fluids such as the engine oil, transmission oil and axle oil. The magnitude of the fuel consumption reduction will depend on how these rapid warm-up devices are arranged, combined and controlled. This paper describes a methodology that was developed to optimize the distribution of coolant heat in the powertrain system during warm-up. A comparative study can be performed to optimize the arrangement of each heat exchanger in any given powertrain system to minimize cost and time early in development.

Vehicle suspension parts are subjected to variable road loads, manufacturing process variation and high installation loads in assembly process. Seam welding can be considered as such process to connect more components and parts. Typical in a Mc Pherson suspension system stabilizer bar link is connected to the strut assembly through ball stud and clamped to a bracket welded to the outer strut tube. Cracks have been observed in the stabilizer bar link bracket welds of vehicles in the field, effecting the functionality of the suspension system. During preliminary phase of product development CAE assessment of the seam weld is carried out against road load data, if the design does not meet the targets enabler studies are carried out in an iterative approach. Various design variables (control factors) can be considered to carry out the iterations.

Vibrations affect vehicle occupants and should be prevented early in design process. Powertrain (PT) wiggle is one of the well-known issues. It is the 3rd order lateral vibration, forced by half shaft inner LH/RH plunging tripod joints [1,2]. Lateral PT resonance (7-15Hz) occurs at certain vehicle speed during acceleration and may excite lateral, pitch and roll PT modes. Typically, PT wiggle occurs in speed range of 5-25kph. Vibration is noticeable on driver and passenger seats mostly in lateral direction. The inner half shaft joints are the major source of vibration. Unfortunately, existing MBD tools like Adams [3] are missing detailed tripod joint representation because of complex mechanical interactions inside the joint. At least three sliding contacts between tripod rollers and joint housing, lubricant inside the can and combination of rotation and plunging make the modeling too complicated.

In recent decades, there has been a growing focus on improving overall vehicle efficiency and fuel economy due to growing customer awareness and more stringent environmental regulations. Effort has been placed on improving the engine efficiency and reducing the losses of the transmission and driveline. One essential component of this process is to correctly size the transmission oil pump as it is one of the main energy consumers in the powertrain. Conversely, the oil pump has a critical mission of ensuring reliable and high quality gear shift as well as supplying lubrication and cooling oil to various components in the transmission. This paper outlines a strategy to systematically understand and quantify the main requirements for sizing the oil pump to ensure adequate performance while minimizing the energy consumption of the pump. The proposed framework is a three-legged approach.

Simplified vehicle dynamics models used to study the driveline durability are typically limited to the longitudinal dynamics and do not account for vertical and pitch dynamics. The influence of suspension on the vehicle ride and handling characteristics is studied extensively in the literature but its impact on the driveline torques is often not considered. In this paper, an effort is made to investigate the influence of suspension compliance on the driveline torque using a planar (longitudinal, pitch and vertical) vehicle dynamics model. An AWD vehicle is studied to understand its impact on the torque levels of both axles (primary and secondary). Subsequently the planar dynamics is explored in the context of anti-squat/anti-dive suspension. The primary focus of the paper is to predict the driveline torque.

Internal combustion engine gets heated up due to continuous combustion of fuel. To keep engine working efficiently and prevent components damage due to very high temperature, the engine needs to be cooled down. Based on power output requirement and provision for cooling system, every engine has it’s unique cooling system. Liquid based cooling systems are majorly implemented in automobile. It’s important to keep in mind that during design phase that, cooling the engine will lower the power to fuel consumption ratio. Therefore, during lower ambient conditions, the cooling system should be able to uniformly increase the temperature of the engine components, engine oil and transmission oil. This is achieved by circulating the coolant through cooling jacket, engine oil heater and transmission oil heater, which will be heated by the combustion heat.

Electronic Stop-Start (ESS) system automatically stops and restarts the engine to save energy, improve fuel economy and reduce emissions when the vehicle is stationary during traffic lights, traffic jams etc. The stop and start events cause unwanted vibrations at the seat track which induce discomfort to the driver and passengers in the vehicle. These events are very short duration events, usually taking less than a second. Time domain analysis can help in simulating this event but it is difficult to see modal interactions and root cause issues. Modal transient analysis also poses a limitation on defining frequency dependent stiffness and damping for multiple mounts. This leads to inaccuracy in capturing mount behavior at different frequencies. Most efficient way to simulate this event would be by frequency response analysis using modal superposition method.