Refine Your Search

Search Results

Viewing 1 to 8 of 8
Journal Article

Power Dense and Robust Traction Power Inverter for the Second-Generation Chevrolet Volt Extended-Range EV

2015-04-14
2015-01-1201
The Chevrolet Volt is an electric vehicle with extended-range that is capable of operation on battery power alone, and on engine power after depletion of the battery charge. First generation Chevrolet Volts were driven over half a billion miles in North America from October 2013 through September 2014, 74% of which were all-electric [1, 12]. For 2016, GM has developed the second-generation of the Volt vehicle and “Voltec” propulsion system. By significantly re-engineering the traction power inverter module (TPIM) for the second-generation Chevrolet Volt extended-range electric vehicle (EREV), we were able to meet all performance targets while maintaining extremely high reliability and environmental robustness. The power switch was re-designed to achieve efficiency targets and meet thermal challenges. A novel cooling approach enables high power density while maintaining a very high overall conversion efficiency.
Journal Article

Superelement, Component Mode Synthesis, and Automated Multilevel Substructuring for Rapid Vehicle Development

2008-04-14
2008-01-0287
This paper presents the new techniques/methods being used for the rapid vehicle development and system level performance assessment. It consists of two parts: the first part presents the automated multilevel substructuring (AMLS) technique, which greatly reduces the computational demands of larger finite element models with millions of degrees of freedom(DOF) and extends the capabilities to higher frequencies and higher level of accuracy; the second part is on the superelement in conjunction with the Component Mode Synthesis (CMS) and also Automated Component Mode Synthesis (ACMS) techniques. In superelement, a full vehicle model is divided into components such as Body-in-white, Front cradle/chassis, Rear cradle/chassis, Exhaust, Engine, Transmission, Driveline, Front suspension, Rear suspension, Brake, Seats, Instrument panel, Steering system, tires, etc. with each piece represented by reduced stiffness, mass, and damping matrices.
Technical Paper

Designing Suspensions to Achieve Desirable Impact Harshness and Impact Shake Performance

2007-04-16
2007-01-0585
Impact Harshness and Impact Shake are two related aspects of ride performance. Vehicle designs often need to meet the conflicting requirements between these two performance areas. The fundamental dynamics and general effect of vehicle and suspension design parameters need to be understood to reduce the cost and time associated with early vehicle development and ensure built-in quality. This study investigates the influence of the parameters in suspension and tire wheel systems on each of the performance metrics. Attempts are made to rank-order the relative sensitivity of each parameter on each of the metrics and propose approaches to improve ride quality.
Technical Paper

Case Study - Experimental Determination of Airborne and Structure-borne Road Noise Spectral Content on Passenger Vehicles

2005-05-16
2005-01-2522
Appropriate road noise levels are critical to perceived quality in today's highly competitive automotive industry. Tire noise is often one of the dominant sources. In order to provide effective noise control schemes it is imperative to fully define the noise paths. In this paper, a case study of an experimental lab method is presented that allows definitive understanding of the structure-borne and airborne spectral contributions of tire noise. For this study, interior noise data were collected using a 10 ft road wheel. Data were collected for the front and rear tires. These measurements contained both the structure-borne and airborne contributions. The same test was performed with the tire physically disconnected from the vehicle structure. This measurement contained only the airborne contribution. The structure-borne contribution was then calculated as the difference in noise levels between the two cases.
Technical Paper

Supplementation of Measured Vehicle Road Loads to Study Vehicle Configuration Changes

2005-04-11
2005-01-1403
Measured vehicle loads, taken during durability events, are commonly used to drive in-lab vehicle subsystem validation testing. The use of measured loads can be problematic due to (a) off-nominal characteristics of the test vehicle, (b) post-test changes to vehicle tuning - bushings, springs, and shocks for example, (c) scheduling, timing and weather requirements, (d) modification of vehicle characteristics by the inclusion of transducers and (e) the cost of executing tests. A general process for supplementing and rationalizing measured vehicle data through the use of correlated multi-body dynamic simulations is presented. Difficulties in modeling tires and other components, as well as difficulties in model correlation for abusive load events are also discussed.
Technical Paper

Comparison of Efficiency Measurements and Simulation Results for Automotive Traction Drives

2005-04-11
2005-01-1463
Mechanical Efficiency of toroidal traction drives is the key parameter for transmission engineers worldwide to accept their use in continuously variable transmissions. In this work, the traction drive efficiencies are investigated analytically as well as experimentally as a function of speed, torque, speed ratio and temperature for two different CVU's. In addition, creep at the traction contact is measured and compared with the prediction of the simulation model. In a stand-alone test rig, the drag torque associated with the power-roller thrust bearing is also measured.
Technical Paper

Dynamic Front Wheel Curb Impact Study

2005-04-11
2005-01-1401
A procedure was developed to predict suspension and cradle loads during a dynamic front wheel curb impact event. Previously, the only way to acquire these types of forces was to run a test. The procedure uses a multibody full vehicle ADAMS model. The impact between the tire and the curb was modeled using a simplified tire model. Specific structural suspension members were modeled with a proprietary method developed by GM to capture the elastic-plastic behavior. The analysis results showed good correlation with the test, and the procedure is now being used at GM.
Technical Paper

Rationale for Technology Selections in GM's PNGV Precept Concept Car Based on Systems Analysis

2000-04-02
2000-01-1567
The CY2000 cornerstone goal of the Partnership for a New Generation of Vehicles (PNGV) is the demonstration in CY 2000 of a 5-passenger vehicle with fuel economy of up 80 mpg (3 l/100km). As a PNGV partner, GM will demonstrate a technology-demonstration concept vehicle, the Precept, having a lightweight aluminum-intensive body, hybrid-electric propulsion system and a portfolio of efficient vehicle technologies. This paper describes: 1) the strategy for the vehicle design including mass requirements, 2) the selection of dual axle application of regenerative braking and electric traction, and 3) the complementary perspective on energy management strategy. This paper outlines information developed through systems analysis that drove technology selections. The systems analyses relied on vehicle simulation models to estimate fuel economy associated with technology selections. Modeling analyses included consideration of both federal test requirements and more severe driving situations.
X