Search Results

Low temperature combustion (LTC) modes are among the advanced combustion technologies which offer thermal efficiencies comparable to conventional diesel combustion and produce ultra-low NOx and particulate matter (PM) emissions. However, combustion timing control, excessive pressure rise rate and high cyclic variations are the common challenges encountered by the LTC modes. These challenges can be addressed by developing model-based control framework for the LTC engine. In the current study, in-cylinder pressure data for dual-fuel LTC engine operation is analyzed for 636 different operating conditions and the heat release rate (HRR) traces are classified into three distinct classes based on their distinct shapes. These classes are named as Type-1, Type-2 and Type-3, respectively.

A potential route to reduce CO2 emissions from heavy-duty trucks is to combine low-carbon fuels and a hybrid-electric powertrain to maximize overall efficiency. A hybrid electric powertrain can reduce the peak power required from the internal combustion engine, leading to opportunities to reduce the engine size but still meet vehicle performance requirements. Although engine downsizing in the light-duty sector can offer significant fuel economy savings mainly due to increased part-load efficiency, its benefits and downsides in heavy-duty engines are less clear. As there has been limited published research in this area to date, there is a lack of a standardized engine downsizing procedure.

A diesel piloted natural gas engine's performance varies depending on operating conditions and has performed best under medium to high loads. It can often equal or better the fuel conversion efficiency of a diesel-only engine in this operating range. This paper presents a study performed on a multi-cylinder Cummins ISB 6.7L diesel engine converted to run stoichiometric natural gas/diesel micro-pilot combustion with a maximum diesel contribution of 10%. This study systematically quantifies and ranks the sensitivity of control factors on combustion and performance while operating at medium loads. The effects of combustion control parameters, including the pilot start of injection, pilot injection pressure, pilot injection quantity, exhaust gas recirculation, and global equivalence ratio, were tested using a design of experiments orthogonal matrix approach.

The development and calibration of modern combustion engines is challenging in the area of continuously tightening emission limits and the necessity for meeting real driving emissions regulations. A focus is on the knowledge of the internal engine processes and the determination of pollutants formations in order to predict the engine emissions. A physical model-based development provides an insight into hardly measurable phenomena properties and is robust against changing input data. With increasing modeling depth the required computing capacities increase. As an alternative to physical modeling, data-driven machine learning methods can be used to enable high-performance modeling accuracy. However, these are dependent on the learned data. To combine the performance and robustness of both types of modeling a hybrid application of data-driven and physical models is developed in this paper as a grey box model for the exhaust emission prediction of a commercial vehicle diesel engine.

Experimental results are combined with a physical understanding of an amperometric NOx-O2 sensor to study the effect of three main operating parameters on the sensor behavior in non diffusion-rate-determining operating conditions. The sensor response to NOx concentration is examined over a range of sensor operating temperatures, reference cell potentials, and second sensing cell potentials. The results show that the sensor sensitivity increases gradually with the sensing cell voltage while the sensor output is almost linearly dependent on NOx concentration for cell voltages higher than ≈ 0.25 V. The results also reveal that reducing the reference cell potential from the typical cell potential (0.42 V) reduces the sensor cross-sensitivity to O2 particularly at high NOx concentrations (>600 [ppm]).

This paper investigates an optimal design of a diesel engine and after-treatment systems for a series hybrid electric forklift application. A holistic modeling approach is developed in GT-Suite® to establish a model-based hardware definition for a diesel engine and an after-treatment system to accurately predict engine performance and emissions. The used engine model is validated with the experimental data. The engine design parameters including compression ratio, boost level, air-fuel ratio (AFR), injection timing, and injection pressure are optimized at a single operating point for the series hybrid electric vehicle, together with the performance of the after-treatment components. The engine and after-treatment models are then coupled with a series hybrid electric powertrain to evaluate the performance of the forklift in the standard VDI 2198 drive cycle.

Gasoline particulate filters (GPFs) are an important aftertreatment system that enables gasoline direct injection (GDI) engines to meet current emission standardsn note of GPFs may need to improonont accumulates on the GPF during engine operation. GPFs are often ‘pa during vehicle operation when the exhaust is sufficiently hot and it contains sufficient oxygen. This paper explores the effect that engine-out soot emissions and the frequency of GPF regeneration have on GPF filtration efficiency. Two GPF technologies were tested on two engine dynamometers as well as two production vehicles on a chassis dynamometer. The engines span a wide range of engine-out particle emissions (a range of almost one order of magnitude). The filtration efficiency of the GPFs were measured with a regulation-compliant particle number system (non-volatile particles > 23 nm), as well as with a particle counter with a lower cutoff of 2.5 nm, and with a differential mobility spectrometer.

The effects of Variable Valve Timing (VVT) on Homogeneous Charge Compression Ignition (HCCI) engine energy distribution and waste heat recovery are investigated using a fully flexible Electromagnetic Variable Valve Timing (EVVT) system. The experiment is carried out in a single cylinder, 657 cc, port fuel injection engine fueled with n-heptane. Exergy analysis is performed to understand the relative contribution of different loss mechanisms in HCCI engines and how VVT changes these contributions. It is found that HCCI engine brake thermal efficiency, the Combined Heat and Power (CHP) power to heat ratio, the first and the second law efficiencies are improved with proper valve timing. Further analysis is performed by applying the first and second law of thermodynamics to compare HCCI energy and exergy distribution to Spark Ignition (SI) combustion using Primary Reference Fuel (PRF). HCCI demonstrates higher fuel efficiency and power to heat and energy loss ratios compared to SI.

This study aims to provide modeling and control approaches for automated manual passenger and commercial vehicle transmissions in order to improve the overall disengagement-gear shifting-engagement performance using electromagnetic powder clutch (EMPC). The rationale behind selecting this clutch is its rapid behavior. During the modeling procedure of the EMPC, the analogy between this type of clutches and dry plate friction clutches has been exploited and a simple control method is proposed. The study also includes modeling method for gear shifting and selecting mechanisms of the automated manual transmission gearbox as well as development and implementation of controllers which is designed for these mechanisms. Automated manual transmission gearbox is utilized due to its combination of ease of construction and ability for electronic automation.

We have developed an original, three-dimensional icing modelling capability, called the “morphogenetic” approach, based on a discrete formulation and simulation of ice formation physics. Morphogenetic icing modelling improves on existing ice accretion models, in that it is capable of predicting simultaneous rime and glaze ice accretions and ice accretions with variable density and complex geometries. The objective of this paper is to show preliminary results of simulating complex three-dimensional features such as lobster tails and rime feathers forming on a swept wing. The results are encouraging. They show that the morphogenetic approach can predict realistically both the overall size and detailed structure of the ice accretion forming on a swept wing. Under cold ambient conditions, when drops freeze instantly upon impingement, the numerical ice structure has voids, which reduce its density.

Honing is a low-speed abrading process to remove metallic and non-metallic materials from a surface. Honing corrects surface errors produced by other machining operations prior to honing. Moreover,, the honing grooves, the volume and the direction of the valleys control the amount of oil available, by keeping the oil on the bore surface and by improving the spreading of the oil. The traditional honing process that uses ceramic abrasives has been replaced by the superior abrasives that is Metal Bonded Diamond [1,2]. However, the main drawback of diamond honing is that it leaves more torn metal and folded metal on surface [3]. The folded and / or torn metal partially covers the honing grooves and interrupts oil flow in groove. Hence, it causes abrasive wear as axial scratches on the cylinder surface. Diamond is the strongest material known that is less friable, wear very little, requires more pressure and tends to plough through metal surface rather than cut.

An aerodynamic analysis methodology which makes efficient use of ANSA and FLUENT software's in the aerodynamic design of tractor-trailer class heavy commercial road vehicles is presented. The aerodynamic drag coefficient of the truck is used as the main control parameter to evaluate the performance of the methodology. Analysis methodology development activities include determining optimal FLUENT software analysis parameters for the defined problem (RANS based turbulence models, wall boundary layer models, solution schemes) and the necessary ANSA mesh generation parameters (boundary layer number and growth rate, wall surface mesh resolution, total mesh resolution). Proposed methodology is first constructed based on CFD simulations for the zero-degree yaw angle case of the 1/8 sized GCM geometry. The present results are within 1% of the experimental data.

Styrene, or ethylbenzene, is mainly used as a monomer for the production of polymers, most notably Styrofoam. In the synthetis of styrene, the feedstock of benzene and ethylene is converted into aromatic oxygenates such as benzaldehyde, 2-phenyl ethanol and acetophenone. Benzaldehyde and phenyl ethanol are low value side streams, while acetophenone is a high value intermediate product. The side streams are now principally rejected from the process and burnt for process heat. Previous in-house research has shown that such aromatic oxygenates are suitable as diesel fuel additives and can in some cases improve the soot-NOx trade-off. In this study acetophenone, benzaldehyde and 2-phenyl ethanol are each added to commercial EN590 diesel at a ratio of 1:9, with the goal to ascertain whether or not the lower value benzaldehyde and 2-phenyl ethanol can perform on par with the higher value acetophenone. These compounds are now used in pure form.

This study aims to determine environmental aspects of an end-of-vehicle recycling process through life cycle assessment (LCA) methodology. Functional unit of the study was an end-of-vehicle with a weight of 1432 kg. System boundaries included transportation of the scrap car to disassembly and shredding facility, disassembly and shredding processes and transportation of the materials to recycling facilities. Data regarding process was gathered from a shredding facility, literature and the libraries of the SimaPro 7.3.2. Gathered data was evaluated through CML 2 baseline 2000 methodology by the means of abiotic depletion, acidification, global warming, ozone depletion, human toxicity, fresh water aquatic ecotoxicity, marine aquatic ecotoxicity, terrestrial ecotoxicity and photochemical oxidation. According to results, transportation and diesel consumption are the important factors for ELV recycling.

This paper presents a large eddy simulation study of the liquid spray mixing with hot ambient gas in a constant volume vessel under engine-like conditions with the injection pressure of 1500 bar, ambient density 22.8 kg/m₃, ambient temperature of 900 K and an injector nozzle of 0.09 mm. The simulation results are compared with the experiments carried out by Pickett et al., under similar conditions. Under modern direct injection diesel engine conditions, it has been argued that the liquid core region is small and the droplets after atomization are fine so that the process of spray evaporation and mixing with the air is controlled by the heat and mass transfer between the ambient hot gas and central fuel flow. To examine this hypothesis a simple spray breakup model is tested in the present LES simulation. The simulations are performed using an open source compressible flow solver, in OpenFOAM.

Unburned hydrocarbon (UHC) and carbon monoxide (CO) emission sources are examined in an optical, light-duty diesel engine operating under low load and engine speed, while employing a highly dilute, partially premixed low-temperature combustion (LTC) strategy. The impact of engine load and charge dilution on the UHC and CO sources is also evaluated. The progression of in-cylinder mixing and combustion processes is studied using ultraviolet planar laser-induced fluorescence (UV PLIF) to measure the spatial distributions of liquid- and vapor-phase hydrocarbon. A separate, deep-UV LIF technique is used to examine the clearance volume spatial distribution and composition of late-cycle UHC and CO. Homogeneous reactor simulations, utilizing detailed chemical kinetics and constrained by the measured cylinder pressure, are used to examine the impact of charge dilution and initial stoichiometry on oxidation behavior.

Natural gas is a challenging fuel for HCCI engines because its single-stage ignition and rapid combustion make it difficult to optimize combustion timing over a significant load range. This study investigates direct injection of a pilot quantity of high-cetane fuel near TDC as a range extension and combustion control mechanism for natural gas HCCI engines. The EGR and load range is studied in a supercharged natural gas HCCI engine equipped with external EGR, intake heating and a direct injection system for n-heptane pilot fuel. The operating range and emissions are of primary interest and are compared between both the baseline HCCI engine with variable intake temperature and the direct injected HCCI (DI-HCCI) engine with constant intake temperature. Test results show the EGR and load range at fixed intake temperature can be extended using pilot direct injection.

Homogeneous Charge Compression Ignition (HCCI) is an emerging combustion technology due to its increased efficiency and decreased NOx emissions. One of the most challenging aspects of HCCI is the regulation of the combustion timing. Unlike conventional combustion modes there is no direct control over the start of combustion. Autoignition timing is a function of the temperature, pressure and composition of the mixture, so to adjust the combustion timing of HCCI changes have to be made to these. Both variable valve timing and variable fuel octane number are effective inputs to achieve cycle-to-cycle combustion control of HCCI combustion timing. The application of these control methods are investigated in this paper. A one-cylinder Ricardo engine is fitted with a 4-valve spark ignition cylinder head equipped with camshaft phasers. These phasers independently adjust both the intake and exhaust camshaft phasing.

A physics-based control-oriented model is developed to dynamically predict cycle-to-cycle combustion timing in transient fueling conditions for Homogeneous Charge Compression Ignition (HCCI) engines. The model simulates the engine cycle from the intake stroke to the exhaust stroke and includes the thermal coupling dynamics caused by the residual gases from one cycle to the next cycle. A residual gas model, a modified knock integral model, a fuel burn rate model, and thermodynamic models for the gas state in combustion and exhaust strokes are incorporated to simulate the engine cycle. The gas exchange process, generated work and completeness of combustion are predicted using semi-empirical correlations. The resulting model is parameterized for the combustion of Primary Reference Fuel (PRF) blends using 5703 simulations from a detailed thermo-kinetic model. Semi-empirical correlations in the model are parameterized using the experimental data obtained from a single-cylinder engine.

The paper describes a novel method for calculating the residual gas fraction and the trapping efficiency in a 2 stroke engine. Assuming one dimensional compressible flow through the inlet and exhaust ports, the method estimates the instantaneous mass flowing in and out from the combustion chamber; later the residual gas fraction and trapping efficiency are estimated combining together the perfect displacement and perfect mixing scavenging models. It is assumed that when the intake port opens, the fresh mixture is pushing out the burned charge without any mixing and after a multiple of the time needed for the largest eddy to perform one rotation, the two gasses are instantly mixed up together and expelled. The result is a very simple algorithm that does not require much computational time and is able to estimate with high level of precision the trapping efficiency and the residual gas fraction in 2 stroke engines.