Search Results

The objective of the current research was to predict and analyze the flow through the grill of air intake system which is positioned behind the front wheel arch of vehicle. Most of the vehicle used today locates the grill of air intake at the front side so to acquire benefit of ram effect. In some cases, however, the grill is located behind the vehicle to improve wading performance. The geometry of air intake system of Land Rover Freelander was used in the modelling approach. The study was focused on different flow speeds on the grill at high load operation where the air speed at the grill side is high and creates negative pressure. The CFD results are validated against experimental data of steady flow test bench.

With boosted HCCI operation on gasoline using residual gas trapping, the amount of residuals was found to be of importance in determining the boundaries of stable combustion at various boost pressures. This paper represents a development of this approach by concentrating on the effects of inlet valve events on the parameters of boosted HCCI combustion with residual gas trapping. It was found that an optimum inlet valve timing could be found in order to minimize NOx emissions. When the valve timing is significantly advanced or retarded away from this optimum, NOx emissions increase due to the richer air / fuel ratios required for stable combustion. These richer conditions are necessary as a result of either the trapped residual gases becoming cooled in early backflow or because of lowering of the effective compression ratio. The paper also examines the feasibility of using inlet valve timing as a method of controlling the combustion phasing for boosted HCCI with residual gas trapping.

The application of Homogeneous Charge Compression Ignition (HCCI) combustion to naturally aspirated engines has shown a much reduced usable load range as compared to spark ignition (SI) engines. The approach documented here applies inlet charge boosting to gasoline HCCI operation on an engine configuration that is typical for SI gasoline engines, in conjunction with residual gas trapping. The latter helps to retain the benefits of much reduced requirement for external heating. In the present work, the achievable engine load range is controlled by the level of boost pressure while varying the amount of trapped residual gas. In addition, it was found that there is a maximum amount of boost that can be applied without intake heating for any given amount of trapped residuals. NOx emissions decrease with increasing amounts of trapped residual.

Negative valve overlapping is widely used for trapping residual burned gas within the cylinder to enable controlled Homogeneous Charge Compression Ignition (HCCI). HCCI has been shown as a promising combustion technology to improve the fuel economy and NOx emissions of gasoline engines. While the importance of in-cylinder flow in the fuel and air mixing process is recognised, the characteristics of air motion with specially designed valve events having reduced valve lift and durations associated with HCCI engines and their effect on subsequent combustion are not yet fully understood. This paper presents an investigation in an optical engine designed for HCCI combustion using EGR trapping. PIV techniques have been used to measure the in-cylinder flow field under motored conditions and a quantitative analysis has been carried out for the flow characterisation with comparison made against the flow in the same engine with conventional valve strategies for SI combustion.

With the high auto ignition temperature of natural gas, various approaches such as high compression ratios and/or intake charge heating are required for auto ignition. Another approach utilizes the trapping of internal residual gas (as used before in gasoline controlled auto ignition engines), to lower the thermal requirements for the auto ignition process in natural gas. In the present work, the achievable engine load range is controlled by the degree of internal trapping of exhaust gas supplemented by intake charge heating. Special valve strategies were used to control the internal retention of exhaust gas. Significant differences in the degree of valve overlap were necessary when compared to gasoline operation at the same speeds and loads, resulting in lower amounts of residual gas observed. The dilution effect of residual gas trapping is hence reduced, resulting in higher NOx emissions for the stoichiometric air/fuel ratio operation as compared to gasoline.

Natural gas has a high auto-ignition temperature, requiring high compression ratios and/or intake charge heating to achieve HCCI (homogeneous charge compression ignition) engine operation. Previous work by the authors has shown that hydrogen addition improves combustion stability in various difficult combustion conditions. It is shown here that hydrogen, together with residual gas trapping, helps also in lowering the intake temperature required for HCCI. It has been argued in literature that the addition of hydrogen advances the start of combustion in the cylinder. This would translate into the lowering of the minimum intake temperature required for auto-ignition to occur during the compression stroke. The experimental results of this work show that, with hydrogen replacing part of the fuel, a decrease in intake air temperature requirement is observed for a range of engine loads, with larger reductions in temperature noted at lower loads.