Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Design & Validation of Low-Cost Sound Intensity Probe

2019-06-05
2019-01-1462
Sound intensity measurement techniques, that used a two-microphone setup, were first developed in the late 1970s. Back then, the focus was on improving precision during testing or post-processing because the equipment available was inherently inaccurate. However, with the advent of modern, sophisticated equipment, the focus has shifted to the apparatus. Availability of phase-matched microphones has made post-test correction obsolete as the microphones eliminate a majority of the errors before the data is even collected. This accuracy, however, comes at a price, as phase-matched microphones are highly priced. This paper discusses employing the method of improving post-processing precision, using inexpensive, current equipment. The phase error of the system is corrected using a simple calibration technique and a handheld phase calibrator that is similar to the one used for amplitude calibration of microphones.
Technical Paper

PHEV Real World Driving Cycle and Energy and Fuel Consumption Reduction Potential for Connected and Automated Vehicles

2019-04-02
2019-01-0307
This paper presents real world driving energy and fuel consumption results for the second-generation Chevrolet Volt plug-in hybrid electric vehicle (PHEV). A drive cycle, local to Michigan Technological University, was designed to mimic urban and highway driving test cycles in terms of distance, transients and average velocity, but with significant elevation changes to establish an energy intensive real world driving cycle for assessing potential energy savings for connected and automated vehicle control. The investigation began by establishing baseline and repeatability of energy consumption at various battery states of charges. It was determined that drive cycle energy consumption under a randomized set of boundary conditions varied within 3.4% of mean energy consumption regardless of initial battery state of charge.
Technical Paper

Methods of Pegging Cylinder Pressure to Maximize Data Quality

2019-04-02
2019-01-0721
Engine cylinder pressure measured with piezo-electric pressure transducers must be referenced or pegged to a known pressure at some point in the engine cycle. Traditionally, the pressure has been pegged to the pressure in the intake manifold plenum at Bottom Dead Center (BDC) at the end of the intake stroke. However, an error in pegging induces an error in the cylinder pressure trace, which has an adverse effect on the entire combustion analysis. This research is focused on assessing the pegging error for several pegging methods across a wide range of engine operating conditions, and ultimately determining best practices to minimize error in pegging and its propagation to calculated combustion metrics. The study was conducted through 1D simulations run in the commercially available GT-Power. The points studied included variations of speed, load, intake runner length and intake valve timing (including Late Intake Valve Closing (LIVC) and Early Intake Valve Closing (EIVC)).
Technical Paper

Spark Mechanism in High Speed Flow

2019-04-02
2019-01-0729
An experimental study was performed to investigate spark ignition and subsequent spark stretch evolution of inert nitrogen charge gas under high-velocity flow conditions across the electrode gap in a constant-volume optical combustion vessel. The vessel is capable of generating various in-cylinder thermodynamic conditions representative of light-duty spark ignition engines. It realizes a high flow velocity of 32 m/s created by a new high cross flow design. The characteristic behavior of the spark stretch was captured through a high-speed imaging of flow under elevated pressure conditions starting from atmosphere to 45 bar. Results show that the spark flowing downstream the spark plug is subject to restrike after electrical breakdown in high speed flows. Spark plug orientations and gap sizes as well as the charge gas pressure are determined to have significant influence on spark stretch development and electrical discharge time prediction.
Technical Paper

Impinged Diesel Spray Combustion Evaluation for Indirect Air-Fuel Mixing Processes and Its Comparison with Non-Vaporing Impinging Spray Under Diesel Engine Conditions

2019-04-02
2019-01-0267
Under low-temperature combustion for the high fuel efficiency and low emissions achievement, the fuel impingement often occurs in diesel engines with direct injection especially for a short distance between the injector and piston head/cylinder wall. Spray impingement plays an important role in the mixing-controlled combustion phase since it affects the air-fuel mixing rate through the disrupted event by the impingement. However, the degree of air entrainment into the spray is hard to be directly evaluated. Since the high spray expansion rate could allow more opportunity for fuel to mix with air, in this study, the expansion rate of impinged flame is quantified and compared with the spray expansion rate under non-vaporizing conditions. The experiments were conducted in a constant volume combustion chamber with an ambient density of 22.8 kg/m3 and the injection pressure of 150 MPa.
Technical Paper

Investigation and Optimization of CAM actuation of an Over-Expanded Atkinson Cycle Spark-Ignited Engine

2019-04-02
2019-01-0250
An over-expanded engine was investigated via engine simulation in this work with a design constrained Atkinson mechanically actuated cycle mechanism. A conventional 4-stroke spark-ignited turbo-charged engine with a compression ratio of 9.2 and peak BMEP of 22 bar was selected as the baseline. With geometry and design constraints including bore, stroke, compression ratio, clearance volumes at TDC firing and gas exchange, and packaging, two over-expanded engine mechanisms with stroke ratios of 1.3 and 1.5 were designed. Starting with a validated 1D engine simulation model which included calibration of the in-cylinder heat transfer model, SI turbulent combustion model, and combustion knock model, several investigations of the two Atkinson variants including cam optimization were studied. This included investigation of the effects of offset piston TDC locations and different durations of the 4-strokes due to the mechanism.
Technical Paper

Influence of Elevated Injector Temperature on the Spray Characteristics of GDI Sprays

2019-04-02
2019-01-0268
When fuel at elevated temperatures is injected into an ambient environment at a pressure lower than the saturation pressure of the fuel, the fuel vaporizes in the nozzle and/or immediately upon exiting the nozzle; that is, it undergoes flash boiling. It is characterized by a two-phase flow regime co-located with primary breakup, which significantly affects the spray characteristics. Under flash boiling conditions, the near nozzle spray angle increases, which can lead to shorter penetration because of increased entrainment. In a multi-hole injector this can cause other impacts downstream resulting from the increased plume to plume interactions. To study the effect of injector temperature and injection pressure with real fuels, an experimental investigation of the spray characteristics of a summer grade gasoline fuel with 10% ethanol (E10) was conducted in an optically accessible constant volume spray vessel.
Technical Paper

Control-Oriented Modeling of a Vehicle Drivetrain for Shuffle and Clunk Mitigation

2019-04-02
2019-01-0345
Flexibility and backlash of vehicle drivelines typically cause unwanted oscillations and noise, known as shuffle and clunk, during tip-in and tip-out events. Computationally efficient and accurate driveline models are necessary for the design and evaluation of torque shaping strategies to mitigate this shuffle and clunk. To accomplish these goals, this paper develops two control-oriented models, i.e., a full-order physics-based model and a reduced-order model, which capture the main dynamics that influence the shuffle and clunk phenomena. The full-order model comprises several components, including the engine as a torque generator, backlash elements as discontinuities, and propeller and axle shafts as compliant elements. This model is experimentally validated using the data collected from a Ford truck. The validation results indicate less than 1% error between the model and measured shuffle oscillation frequencies.
Technical Paper

Process for Study of Micro-pilot Diesel-NG Dual Fuel Combustion in a Constant Volume Combustion Vessel Utilizing the Premixed Pre-burn Procedure

2019-04-02
2019-01-1160
A constant volume spray and combustion vessel utilizing the pre-burn mixture procedure to generate pressure, temperature, and composition characteristic of near TDC conditions in compression ignition engines was modified with post pre-burn gas induction to incorporate a premixed methane gas prior to diesel injection to simulate processes in dual fuel engines. Two variants of the methane induction system were developed and studied. The first used a high-flow modified direct injection injector and the second utilized auxiliary ports in the vessel that are used for normal intake and exhaust events. Flow, mixing and limitations of the induction systems were studied. As a result of this study the high-flow modified direct injection injector was selected because of its controlled actuation and rapid closure. Further studies of the induction system limits post pre-burn were conducted to determine the pressure and temperature limits of the methane autoignition.
Technical Paper

Computationally Efficient Reduced-order Powertrain Model of a Multi-mode Plug-in Hybrid Electric Vehicle for Connected and Automated Vehicles

2019-04-02
2019-01-1210
This paper presents the development of a reduced-order powertrain model for energy and SOC estimation of a multi-mode plug-in hybrid electric vehicle with velocity and elevation inputs. Such a model is intended to overcome the computational inefficiencies of higher fidelity powertrain and vehicle models in short and long horizon optimization efforts such as Coordinated Adaptive Cruise Control (CACC), Eco Approach and Departure (Eco AND), Eco Routing, and PHEV mode blending. The reduced-order powertrain model enables Connected and Automated Vehicles (CAVs) to utilize the onboard sensor and connected data to quickly react and plan their maneuvers to highly dynamic road conditions with minimal computational resources. Although overall estimation accuracy is less than neural network and high-fidelity models, emphasis on runtime minimization with reasonable estimation accuracy enables energy optimization of CAV without a need for computationally expensive server-based models.
Technical Paper

Control Strategy and Energy Recovery Potential for P2 Parallel Hybrid Step Gear Automatic Transmissions

2019-04-02
2019-01-1302
The purpose of this investigation is to present a control strategy and energy recovery potential for P2 parallel hybrid step gear automatic transmissions. The automatic transmission types considered for the investigation are rear wheel drive a dual clutch transmission and a 10 speed planetary automatic equipped each equipped with a significant electric motor between the engine and transmission. The governing equations of clutch-to-clutch upshift controls are presented for each transmission type and various strategies are explored for executing the upshift under various input torque levels, shift times and engine torque management approaches. A lumped parameter dynamic model including the P2 electrification system is utilized for each transmission type to represent dynamic behavior representative of that expected in vehicle for achieving various levels of shift quality assessed with vibration dose value.
Technical Paper

FD&E Total Life T-Sample Residual Stress Analytical Predictions and Measured Results

2019-04-02
2019-01-0528
The SAE Fatigue Design & Evaluation Committee is actively working on a total life project for weldments, in which the welding residual stress is a key contributor to an accurate assessment of fatigue life. Physics-based welding process simulation and various types of residual stress measurement were pursued to provide a sufficiently accurate representation of the residual stress field at the failure location in the fatigue samples. A well-controlled and documented robotic welding process was used for all sample fabrication to provide accurate inputs for the welding simulations. Both destructive (contour method, x-ray diffraction (XRD) with etching) and non-destructive (surface XRD, energy dispersive diffraction (EDD), neutron diffraction(ND)) residual stress measurements were performed on the same or similarly welded samples. The sample is constructed with multiple-pass fillet welds, which induce large gradients in residual stress through the one-inch thickness.
Technical Paper

Ducted Fuel Injection: Effects of Stand-off Distance and Duct Length on Soot Reduction

2019-04-02
2019-01-0545
Ducted fuel injection (DFI) has been shown to be an effective method to significantly reduce soot formation in mixing controlled compression ignition (MCCI) diesel flames. This reduction has been demonstrated in both combustion vessels and in an optical engine. The mechanisms driving the soot reduction are, at this time, not fully understood. There are many geometrical variable options, and optimal configurations are also not immediately evident. The objective of this study is to show the effects of some of these geometric variables, namely stand-off distance (0.1-6mm) for a 2x14mm duct, and duct length (8-14mm) at a given stand-off distance of 0.1mm. A 137m on-axis single-hole injector operated at 100-250MPa was used in a continuous flow, constant pressure vessel. Results show that the shortest stand-off distance of 0.1mm yields the greatest soot reduction for a 2x14mm duct. Also, at the stand-off distance of 0.1mm, the longer the duct, the greater the soot reduction.
Technical Paper

Numerical Parametric Study of a Six-Stroke Gasoline Compression Ignition (GCI) Engine Combustion

2019-04-02
2019-01-0207
Numerical investigation of engine performance and emissions of a six-stroke gasoline compression ignition (GCI) engine combustion at low load conditions is presented. In order to identify the effects of additional two strokes of the six-stroke engine cycle on the thermal and chemical conditions of charge mixtures, an in-house multi-dimensional CFD code coupled with high fidelity physical sub-models along with the Chemkin library was employed. The combustion and emissions were calculated using a reduced chemical kinetics mechanism for a 14-component gasoline surrogate fuel. Two power strokes per cycle were achieved using multiple injections during compression strokes. Parametric variations of injection strategy viz., individual injection timing for both the power strokes and the split ratio that enable the control of combustion phasing of both the power strokes were explored.
Technical Paper

Methodology to Perform Conjugate Heat Transfer Modeling for a Piston on a Sector Geometry for Direct-Injection Internal Combustion Engine Applications

2019-04-02
2019-01-0210
The increase in computational power in recent times has led to multidimensional computational fluid dynamics (CFD) modeling tools being used extensively for optimizing the diesel engine piston design. However, it is still common practice in engine CFD modeling to use constant uniform boundary temperatures. This is either due to the difficulty in experimentally measuring the component temperatures or the lack of measurements when simulation is being used predictively. This assumption introduces uncertainty in heat flux predictions. Conjugate heat transfer (CHT) modeling is an approach used to predict the component temperatures by simultaneously modeling the heat transfer in the fluid and the solid phase. However, CHT simulations are computationally expensive as they require more than one engine cycle to be simulated to converge to a steady cycle-averaged component temperature.
Technical Paper

Investigation of the Effects of Heat Transfer and Thermophysical Properties on Dynamics of Droplet-Wall Interaction

2019-04-02
2019-01-0296
Fuel spray-wall interaction frequently occurs on intake manifold wall in the port fuel injection engine and on the piston in the direct injection engine, especially during the cold start. The heat transfer between the spray and wall is involved in this interaction process and influences the dynamics of the impinged spray which can further affect the engine performance. The physics of impact dynamics of a single droplet serves as a fundamental for better comprehension of spray impingement. In our previous studies, we have focused on diesel droplets, at ambient temperature, impinging on both heated and non-heated wall and found impinged droplet morphology differences. To understand the effect of heat transfer and thermophysical properties on dynamics of droplet-wall interaction better, droplet temperature variation was introduced in this study. Therefore, different conditions were framed to explore the impact of thermophysical properties of the droplet.
Technical Paper

The Adaptive Cycle Engine on Standard Duty Cycles

2019-04-02
2019-01-0232
Continuing research introduced at the 2018 WCX conference, this paper shows the result of simulations where a midsize sedan (1700 kg) fitted with an adaptive cycle engine and a CVT is operated over three standard duty cycles: US06, UDDS, and HWFET, and compared with the results obtained from other engine cycles installed on the same vehicle. Four different engine cycles are compared: conventional 4-stroke, 6-stroke cycle with no air storage, 6-stroke cycle with air storage, and fully adaptive cycle with air storage and a number of strokes determined by instantaneous demand and state of charge of the storage tank. Results show that the fully adaptive engine achieves a better mileage in all scenarios, closely followed by the partially adaptive 6-stroke cycle with storage. Gains over a conventional 4-stroke powerplant range from 3.4 mpg on the HWFET cycle, to 7.6 mpg on the UDDS cycle.
Technical Paper

Improving the Michigan Tech Formula SAE Design Process

2019-04-02
2019-01-0807
Michigan Tech Formula SAE is a student-led team that designs and builds an open-wheel race car to compete with similar teams from other universities in early May each year. The team has adopted a vehicle development process where the design, build, and test/compete phases happen in consecutive years. This process is motivated by the need to perform validation testing in the fall prior to competition due to Houghton winters lingering well into April. In order to compete every year, all three phases are always in-process to ensure the consecutive completion vehicles. As a student organization, Formula SAE membership has a two to three year turnover rate. This limited organizational memory results in redesign rather than re-use of parts. Simple parts are easier to re-model than manually search a directory structure for an existing design. This redundant work is wasted effort and is often results in repeating poor design features that had been improved by previous team members.
Technical Paper

Route Optimized Energy Management of a Connected and Automated Multi-mode Hybrid Electric Vehicle using Dynamic Programming

2019-04-02
2019-01-1209
This paper presents a methodology to optimize the blending of Charge Depleting (CD) and Charge Sustaining (CS) modes in a multi-mode plug-in hybrid electric vehicle (PHEV) that reduces overall energy consumption when the selected route cannot be drive purely electric. The PHEV used in this investigation is the second generation Chevrolet Volt and as many as four instrumented vehicles were utilized simultaneously on road to acquire validation data. The optimization method utilized is dynamic programming (DP) and is paired with a reduced fidelity propulsion system and vehicle dynamics model to enable compatibility with embedded controllers and be computationally efficient of the optimal blended operating scheme over an entire drive route.
Technical Paper

Optimizing Thermal Efficiency of a Multi-Cylinder Heavy Duty Engine with E85 Gasoline Compression Ignition

2019-04-02
2019-01-0557
Gasoline compression ignition (GCI) using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation (EGR)) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high temperature combustion with reduced amounts of EGR appears more practical. Previous studies with 93 AKI gasoline demonstrated that the port and direct injection strategy exhibited the best performance, but the premature combustion event prevented further increase in the premixed gasoline fraction and efficiency.
X