Search Results

For electric vehicles the ability for regenerative braking reduces the use of friction brakes. Particularly on the rear axle of vehicles with reduced dynamic requirements such as urban vehicles, this can offer a potential for downsizing or, in extreme cases, even the elimination of the friction brakes on the rear axle. Due to the fact that the rear axle service brakes also represent the typical parking brake location in SoA (State-of-Art) vehicles, a rigorous rethinking of the parking brake concept is necessary to incorporate safe vehicle standstill management for such novel brake system topology. This research study introduces a novel parking brake design that covers SoA but also legal requirements while retaining potentials associated with the elimination of the rear service brakes such as cost and packaging.

India contributed to 11% of the global road accidents and was ranked 1st among road deaths according to the latest World Health Organization (WHO) report 2018. Indian National Highways (NH) is a meagre 5% of the country’s road network but accounts for 55% of the road accidents and 61% of the road deaths. Majority of the freight traffic is ferried by Commercial Vehicles (CV) or trucks along these highways and this in turn increases the probability of them being involved in a road accident. The country’s economy is forecasted to thrive in the coming years and hence the requirement of CVs is aligned to international categorisation in the supply chain and shall play a pivotal role. In the year 2019, 13,532 road deaths were associated with CV occupants. The trucking industry is an unorganized sector wherein the illegal overloading of vehicles and over-the-limit driving hours pose a serious threat to road users.

Nowadays automobiles are getting smart and there is a growing need for the physical behavior to become part of its software. This behavior can be described in a compact form by differential equations obtained from modeling and simulation tools. In the offline simulation domain the Functional Mockup Interface (FMI) [3], a popular standard today supported by many tools, allows to integrate a model with solver (Co-Simulation FMU) into another simulation environment. These models cannot be directly integrated into embedded automotive software due to special restrictions with respect to hard real-time constraints and MISRA compliance. Another architectural restriction is organizing software components according to the AUTOSAR standard which is typically not supported by the physical modeling tools. On the other hand AUTOSAR generating tools do not have the required advanced symbolic and numerical features to process differential equations.

Software-in-the-Loop (SiL) test environments are the ideal virtual platforms for enabling continuous-development, -integration, -testing -delivery or -deployment commonly referred as Continuous-X (CX) of the complex functionalities in the current automotive industry. This trend especially is contributed by several factors such as the industry wide standardization of the model exchange formats, interfaces as well as architecture definitions. The approach of frontloading software testing with SiL test environments is predominantly advocated as well as already adopted by various Automotive OEMs, thereby the demand for innovating applicable methods is increasing. However, prominent usage of the existing monolithic architecture for interaction of various elements in the SiL environment, without regarding the separation between functional and non-functional test scope, is reducing the usability and thus limiting significantly the cost saving potential of CX with SiL.

A major source for soot particle formation in Gasoline-Direct-Injection (GDI) engines are fuel-rich zones near walls as a result of wall wetting during injection. To address this problem, a thorough understanding of the wall film formation and evaporation processes is necessary. The wall temperature before, during and after fuel impingement is an important parameter in this respect, but is not easily measured using conventional methods. In this work, a recently developed laser-based phosphor thermography technique is implemented for investigations of spray-induced surface cooling. This spatially and temporally resolved method can provide surface temperature measurements on the wetted side of the surface without being affected by the fuel-film. Zinc oxide (ZnO) particles, dispersed in a chemical binder, were deposited onto a thin steel plate obtaining a coating thickness of 17 μm after annealing.

Filtration of diesel and gasoline fuel in automotive applications is affected by many external and internal parameters, e.g. vibration, temperature, pressure, flow pulsation, and engine start-stop. Current test procedures for automotive fuel filters, proposed by most of the researchers and organizations including Society for Automotive Engineers (SAE) and International Organization for Standardization (ISO), do not apply the previously mentioned real-world-conditions. These operating conditions, which are typical for an automotive fueling system, have a significant effect on fuel filtration and need to be considered for the accurate assessment of the filter. This requires the development of improved testing procedures that will simulate the operating conditions in a fuel system as encountered in the real world.

AUTOSAR (AUTomotive Open System ARchitecture) is a worldwide standard for automotive basic software in line with an architecture that eases exchange and transfer of application software components between platforms or companies. AUTOSAR provides the standardized architecture together with the specifications of the basics software along with the methodology for developing embedded control units for automotive applications. AUTOSAR matured over the last several years through intensive development, implementation and maintenance. Two main releases (R3.2 and R4.0) represent its current degree of maturity. AUTOSAR is driven by so called core partners: leading car manufacturers (BMW, Daimler, Ford, GM, PSA, Toyota, Volkswagen) together with the tier 1 suppliers Continental and Bosch. AUTOSAR in total has more than 150 companies (OEM, Tier X suppliers, SW and tool suppliers, and silicon suppliers) as members from all over the world.

A new high-performance interchip interface, called Serial WireRing, is introduced. It combines technically mature and established methods, whereby Serial WireRing provides a simple, robust and very inexpensive solution to replace the Serial Peripheral Interface (SPI). Serial WireRing uses a daisy chain ring topology, realized by unidirectional point-to-point connections from device to device. Serial WireRing is realized by a simple “wire ring” with CMOS, LVDS, optical or any other suitable signaling, even mixed. Therefore it has a very low pin count. In order to minimize the latency each slave transmits the data that it receives with 1 bit delay only. In order to avoid clock/data skew, the serial data and clock are merged into one bitstream. A corresponding clock is extracted at each receiver by a clock and data recovery circuit, driven by a simple internal oscillator.

Environmental consciousness and tightening emissions legislation push the market share of electronic fuel injection within a dynamically growing world wide small engines market. Similar to automotive engines during late 1980's, this opens up opportunities for original equipment manufacturers (OEM) and suppliers to jointly advance small engines performance in terms of fuel economy, emissions, and drivability. In this context, advanced combustion system analyses from automotive engine testing have been applied to a typical production motorcycle small engine. The 125cc 4-stroke, 2-valve, air-cooled, single-cylinder engine with closed-loop lambda-controlled electronic port fuel injection was investigated in original series configuration on an engine dynamometer. The test cycle fuel consumption simulation provides reasonable best case fuel economy estimates based on stationary map fuel consumption measurements.

With the development of start stop technology to improve fuel economy and to reduce carbon dioxide (CO2) emissions, the information of State of Charge (SOC) of the battery is highly desirable. Recent days the battery sensors are used in mid-segment and luxury automobiles that monitors the current, voltage and temperature of the battery and calculates the charge model and sends the information via CAN or LIN. These dedicated sensors are intended to perform various functions other than basic start stop. Hence these sensors are proven to be expensive for emerging market, which is intended to perform only basic start stop as the market is looking for a low cost solution. Bosch- India has developed and implemented a novel idea of bringing a low cost and reliable battery charge detection algorithm that can be realized within the Electronic Control Unit (ECU) without a dedicated sensor.

This study presents measurements of transient flow field and spray structures inside an optically accessible DISI (direct-injection spark-ignition) internal combustion engine. The flow field has a direct effect upon mixture and combustion processes. Given the need to increase the efficiency and performance of modern IC engines and thus reduce emissions a detailed understanding of the flow field is necessary. The method of choice was high-speed two-component particle image velocimetry (PIV) imaging a large field of view (43 x 44 mm₂). To capture the temporal evolution of the main flow features the repetition rate was set to 6 kHz which resolves one image per 1° crank angle (CA) at 1000 rpm. The crank angle range recorded was the latter half of the compression stroke at various engine speeds as well as various charge motions (neutral, tumble and swirl). Moreover, consecutive cycles were recorded allowing a detailed investigation of cycle-to-cycle variations.

The reduction of nitrous oxides in the exhaust gases of internal combustion engines using a urea water solution is gaining more and more importance. While maintaining the future exhaust gas emission regulations, like the Euro 6 for passenger cars and the Euro 5 for commercial vehicles, urea dosing allows the engine management to be modified to improve fuel economy as well. The system manufacturer Robert Bosch has started early to develop the necessary dosing systems for the urea water solution. More than 300.000 Units have been delivered in 2007 for heavy duty applications. Typical dosing quantities for those systems are in the range of 0.01 l/h for passenger car systems and up to 10 l/h for commercial vehicles. During the first years of development and application of urea dosing systems, instantaneous flow measuring devices were used, which were not operating fully satisfactory.

1 High precision high pressure diesel common rail fuel injection systems play a key role in emission control, fuel consumption and driving performance. Deposits have been observed on internal injector components, for example in the armature assembly, in the slots of the piston and on the nozzle needle. The brownish to colourless deposits can adversely impact driveability and result in non-compliance with the Euro 4 or Euro 5 emission limits. The deposits have been extensively studied to understand their composition and their formation mechanism. Due to the location of these deposits, the influence of combustion gas can be completely ruled out. In fact, their formation can be explained by interactions of certain diesel fuel additives, including di- and mono-fatty acids. This paper describes the methodology used and the data generated that support the proposed mechanisms. Moreover, approaches to avoid such interactions are discussed.

For about 20 years now, legislation for emission standards has become more and more strict. Main current standards are LEVII legislation for US- and EU4 for the European Market. Many emerging markets like e.g. China, India, Russia adopt EU regulations (directly or modified. Mid of 90's discussions began on restrictions and legislation for CO2 emissions. The European commission recently proposed concrete legislation standards for 2012 and 2020. These will have strong influence on the strategies of the Car Manufacturers. Single measures like start stop will be of general interest. But for reaching the fleet average combinations of measures in a single engine configuration will be necessary. Bosch system solutions for engine- and power-train management are available for the whole span of world car segments, ranging from value concepts optimized for emerging markets up to high feature solutions for most stringent requirements world wide.

As a result of the increased complexity of today's power trains, the traditional ways of designing engine control systems essentially through ad hoc methods and experimental tuning will no longer provide the desired level of performance. Further, it is too time-consuming due to the calibration process. In this paper, a novel model-based controller is described which accommodates many of today's demands on controller development of the automotive industry. The control problem treated here is a boost pressure control of a turbocharged diesel engine with a variable nozzle turbine (VNT). Depending on the injected fuel and the current speed of the diesel engine, the boost pressure has to follow a desired trajectory. Since the system is essentially nonlinear, a robust nonlinear controller is used. The tracking problem is treated by a control method which combines the Internal Model Control (IMC) structure with the flatness-based approach to design feedforward controllers.

In the last decades the development of Diesel engines has made substantial progress. New, powerful and scalable injection systems have been introduced. In consequence Diesel systems are continuously gaining market share in many places of the world. Advanced direct injection engines with systems like the electronically controlled distributer pump, the unit injection system and of course the common rail system are replacing the chamber engines in all automotive applications. This is all unthinkable without the electronic management of these injection systems by means of Electronic Diesel Control units (EDC). The following presentation describes the status and some future trend of technology of EDCs with particular emphasis on functional and on software development. It also outlines the challenge of global automotive industry that requires global development and application services from its tier 1 suppliers.

During the acquisition phase brake system supplier have to make predictions on a system's thermal behavior based on very few reliable parameters. Increasing system knowledge requires the usage of different calculation models along with the progress of the project. Adaptive modeling is used in order to integrate test results from first prototypes or benchmark vehicles. Since changes in the brake force distribution have a great impact on the simulation results fading conditions of the linings have to be integrated as well. The principle of co-simulation is used in order to use the actual brake force distribution of the system.

The demand for more security, economy, and comfort as well as for a reduced environmental impact increases the importance of electronic components for vehicles. The development of such systems is determined by the requirement of an improved functionality and co-requisite the demand for limited costs. In order to fulfil these demands and taking into consideration the increase of complexity and the melting together to a car wide web, Bosch is developing a structuring concept called CARTRONIC®. This concept is supposed to be open and neutral regarding automotive manufactures and suppliers. The analysis of vehicle control systems via this method is based on formal rules for structuring and modelling. The function-related aspect of CARTRONIC® was represented already at the SAE'98 World Congress. Furthermore the safety-related feature was introduced in more detail at the SAE'99 World Congress. The result of the analysis is an object structure of logical components with defined interfaces.

The new generation of drive-by-wire systems currently under development has demanding requirements on the electronic architecture. Functions such as brake-by-wire or steer-by-wire require continued operation even in the presence of component failures. The electronic architecture must therefore provide fault-tolerance and real-time response. This in turn requires the operating system and the communication layer to be predictable, dependable and composable. It is well known that this properties are best supported by a time-triggered approach. A consortium consisting of German and French car manufacturers and suppliers, which aims at becoming a working group within the OSEK/VDX initiative, the OSEKtime consortium, is currently defining a specification for a time-triggered operating system and a fault-tolerant communication layer.1 The operating system and the communication layer are based on applicable interfaces of the OSEK/VDX standard.

The manufacturers of passenger cars increasingly assign development and production of complete subsystems to the supplying industry. A brake system supplier has to give predictions about system quality and performance long time before the first prototypical system is built or even before the supplier gets the order for system development. Nowadays, the usage of computer-aided system design and simulation is essential for that task. This article presents a tool designed to support the development process. A special focus will be on how to define quality. A formal definition of quality is provided, illustrated and motivated by two examples.