Search Results

With the advent of this new era of electric-driven automobiles, the simulation and virtual digital twin modeling world is now embarking on new sets of challenges. Getting key insights into electric motor behavior has a significant impact on the net output and range of electric vehicles. In this paper, a complete 3D CFD model of an Electric Motor is developed to understand its churning losses at different operating speeds. The simulation study details how the flow field develops inside this electric motor at different operating speeds and oil temperatures. The contributions of the crown and weld endrings, crown and weld end-windings, and airgap to the net churning loss are also analyzed. The oil distribution patterns on the end-windings show the effect of the centrifugal effect in scrapping oil from the inner structures at higher speeds. Also, the effect of the sump height with higher operating speeds are also analyzed.

The study focuses on understanding the air and oil flow characteristics within a ball bearing during high-speed rotation, with a particular emphasis on optimizing frictional heat dissipation and oil lubrication methods. Computational fluid dynamics (CFD) techniques are employed to analyze the intricate three-dimensional airflow and oil flow patterns induced by the motion of rotating and orbiting balls within the bearing. A significant challenge in conducting three-dimensional CFD studies lies in effectively resolving the extremely thin gaps existing between the balls, races, and cages within the bearing assembly. In this research, we adopt the ball-bearing structured meshing strategy offered by Simerics-MP+ to meticulously address these micron-level clearances, while also accommodating the rolling and rotation of individual balls. Furthermore, we investigate the impact of different designs of the lubrication ports to channel oil to other locations compared to the ball bearings.

This article analyzes the aerodynamic performance of Class 8 tractor-trailer geometries made available by the Environmental Protection Agency (EPA) using CFD simulation. Large Eddy Simulations (LES) were carried out with the CFD package, Simerics-MP+. A Sleeper tractor and a 53-foot box trailer configuration was considered. The configuration featured a detailed underbody, an open-grille under-hood engine compartment, mirrors, and the radiator and condenser. Multiple tractor-trailer variants were studied by adding aerodynamic surfaces to the baseline geometries. These include tank fairings and side extenders for the cabins, two types of trailer skirts, and a trailer tail. The effect of these devices towards reducing the overall vehicle drag was investigated. Mesh generation was carried out directly on the given geometry, without any surface modifications, using Simerics’ Binary-Tree unstructured mesher.

Modern gearboxes are meticulously engineered with three primary objectives: enhancing load-carrying capacity, minimizing noise, vibration, and harshness (NVH), and optimizing efficiency. Efficiency, in particular, holds paramount significance due to gearboxes’ substantial influence on energy consumption. One effective strategy for boosting efficiency involves curbing churning losses, stemming from the movement of oil within the gearbox housing. Computational fluid dynamics (CFD) techniques have emerged as invaluable tools for visualizing oil flow dynamics within gearboxes and pinpointing avenues for mitigating churning losses. In the context of electric vehicles (EVs), specifically battery electric vehicles (BEVs), extending their driving range is a top priority. Achieving this hinges on the design of an efficient gearbox.

Positive displacement pumps are key components in automotive and hydraulic fluid systems, often serving as the primary power source and a major source of noise in both on-highway and off-highway vehicles. Specifically, gerotor pumps are widely utilized in vehicle coolant, lubricating, and other fluid systems for both conventional and electric powertrains. This study introduces a novel method for predicting noise in gerotor pumps by combining a Computational Acoustics (CA) approach with a 3D Computational Fluid Dynamics (CFD) approach, both implemented in the Simerics–MP+ code. The CFD simulation includes the detailed transient motion of the rotors (including related mesh motion) and models the intricate cavitation/air release phenomena at varying pump speeds. The acoustic simulation employs a Ffowcs–Williams Hawkings (FW–H) integral formulation to predict sound generation and propagation based on the detailed flow field predictions from the CFD model.

The thermal performance of an engine coolant system is efficient when the engine head temperature is maintained within its optimum working range. For this, it is desired that air should not be entrapped in the coolant system which can lead to localized hot spots at critical locations. However, it is difficult to eliminate the trapped air pockets completely. So, the target is to minimize the entrapped air as much as possible during the coolant filling and deaeration processes, especially in major components such as the radiator, engine head, pump etc. The filling processes and duration are typically optimized in an engine test stand along with design changes for augmenting the coolant filling efficiency. However, it is expensive and time consuming to identify air entrapped locations in tests, decide on the filling strategy and make the design changes in the piping accordingly.

This paper reports on a transient, three-dimensional computational fluid dynamics (CFD) study of flow and heat transfer in the complete fuel system of an inline 6-cylinder, direct injection (DI) diesel engine used in commercial applications. The CFD software Simerics-MP+ was used for this purpose. Diesel engine development, to meet fuel economy and exhaust emission standards, requires the precise integration of each component in the fuel system in order to reliably deliver the fuel to the combustion chamber as a function of crank angle to the combustion chamber, at the specified injection pressure. Both the model set-up and run times are practical, thus the simulation tool can play a key role in the design and development of diesel engine fuel systems.

Ducted fuel injection (DFI), a concept that utilizes fuel injection through ducts, was implemented in a constant pressure High Temperature Pressure Vessel at 60 bar ambient pressure, 800-1000 K ambient temperature, and 21 % oxygen. The ducts were 14 mm long and placed 3-4.7 mm from the orifice exit. The duct diameters ranged from 1.6-3.2 mm and had a rounded inlet and a tapered outlet. Diesel fuel was used in single-orifice fuel injectors operating at 250 MPa rail pressure. The objective of this work was to study soot reduction for various combinations of orifice and duct diameters. A complete data set was taken using the 150 μm orifice. A smaller data set was acquired for a 219 μm orifice, showing similar trends. Soot reduction peaked at an optimal duct diameter of 2-2.25 mm, corresponding to an 85-90 % spray area reduction for the 150 μm orifice. Smaller or larger duct diameters were less effective. Duct diameter had a minimal effect on ignition delay.

Centrifugal pumps are widely used in different thermal fluid systems in automobile industries. Computational fluid dynamics (CFD) analysis of such a thermal fluid system depends on the accurate component modeling of the system components. This paper presents CFD analysis of a centrifugal pump with two different approaches: Transient (moving grid) and the steady state - Multiple Reference Frame (MRF) methods using a commercial CFD solver Simerics MP+®. In addition, flow and pressure drop data obtained using CFD simulations of a vehicle coolant hydraulic system was compared to results from rig test data. The Transient method incorporates the real motion of the pump blades geometry and temporal flow solutions are obtained for instantaneous positions of the blade geometry. In MRF approach, the flow governing equations for the stationary zone are solved in the absolute/inertial reference frame, whereas flow in the moving zone is solved in the relative/non-inertial reference frame.

Trapped air bubbles inside coolant systems have adverse effect on the cooling performance. Hence, it is imperative to ensure an effective filling and de-aeration of the coolant system in order to have less air left before the operation of the coolant system. In the present work, a coolant/air multiphase VOF method was utilized using the commercial CFD software SimericsMP+® to study the coolant filling and subsequent de-aeration process in a Battery Electric Vehicle (BEV) cooling system. First, validations of the numerical simulations against experiments were performed for a simplified coolant recirculation system. This system uses a tequila bottle for de-aeration and the validations were performed for different coolant flow rates to examine the de-aeration efficiency. A similar trend of de-aeration was captured between simulation and experimental measurement.

A multi-year Power System R&D project was initiated with the objective of developing an off-road hybrid heavy-duty concept diesel engine with front end accessory drive-integrated energy storage. This off-road hybrid engine system is expected to deliver 15-20% reduction in fuel consumption over current Tier 4 Final-based diesel engines and consists of a downsized heavy-duty diesel engine containing advanced combustion technologies, capable of elevated peak cylinder pressures and thermal efficiencies, exhaust waste heat recovery via SuperTurbo™ turbocompounding, and hybrid energy recovery through both mechanical (high speed flywheel) and electrical systems. The first year of this project focused on the definition of the hybrid elements using extensive dynamic system simulation over transient work cycles, with hybrid supervisory controls development focusing on energy recovery and transient load assist, in Caterpillar’s DYNASTY™ software environment.

The present work deals with the development of a CFD method to simulate water fording/water wading for a passenger car. Water wading of automobiles in different water depths can lead to water ingestion into the air induction snorkel. This is unfavourable as this ingested water can cause the malfunction of the engine. This takes on an added importance when designing multi-terrain vehicles, where the interest could be in wading water effectively in many scenarios. The design of the snorkel, its position and height can be important in preventing water from entering the Air Induction System (AIS) and hence the engine. So, a water fording test of a vehicle is conducted to ensure the efficacy of the AIS snorkel in preventing water entering the AIS system. The ability of numerical simulations to effectively replicate testing performed in a long water tank is put to test in this paper. The CFD method development has been done using the commercial code, Simerics-MP+®.

This paper details results of a numerical and experimental investigation into the relative performance of vaned and vaneless mixed flow turbines for application to medium and heavy-duty diesel engines utilizing pulse exhaust systems. Previous investigations into the impact of nozzle vanes on turbine performance considered only open turbine housings, whereas a majority of medium and heavy-duty diesel engine applications are six-cylinder engines using pulse exhaust systems with divided turbines. The two turbine stages for this investigation were carefully designed to meet the constraints of engines with pulse exhaust systems and to control confounding factors that would undermine the vaned vs vaneless performance comparison. Detailed CFD analysis and turbine dynamometer test results confirm a significant efficiency advantage for the vaned turbine stage under both full and partial admission conditions.

During a vehicle drive cycle, the oil in the engine oil pan sloshes very vigorously due to the acceleration of the vehicle. This can cause the pickup tube in the engine oil pan to become uncovered from oil and exposed to air, which affects the lubrication pump performance. Engine oil pan sloshing is inherently a 3D problem as the free oil surface is constantly changing. Multi-dimensional Computational Fluid Dynamics (CFD) methods are very useful to simulate such problems with high detail and accuracy but are computationally very expensive. Part of the engine lubrication system, such as the pump, can be modelled in 1D which can predict accurate results at relatively high computational speeds. By utilizing the advantages of both 1D and 3D CFD models, a coupled 1D-3D simulation approach has been developed to capture the detailed oil sloshing phenomenon in SimericsMP+ and the system level simulation is conducted in GT-SUITE where 3D spatial data is not required.

This paper reports on engineering insights that can be gained from a rigorous, transient, three-dimensional CFD analysis of the complete lubrication system of automotive internal combustion engines. Building such a model is a formidable task because the computational domain of such a model is vast and includes scores of bearings as well as components such as the pump, pressure relief valve, oil filter, oil cooler, piston cooling jets etc. Thus far, the only publication on 3D CFD analysis of an engine lubrication system was for a 16-cylinder engine in which the feasibility and the potential opportunities of such a model were demonstrated. The aim of this work is to cover four engineering topics of interest in a lubrication system: 1. Showcase the capability of the CFD tool to accurately, robustly and reliably predict the engine lube system performance of a wide variety of automotive engines with no reliance on tuning the inputs.

This paper reports on a novel three-dimensional computational fluid dynamics (CFD) and heat transfer coupled methodology for analyzing piston cooling using oil jets. The method primarily consists of models of the fluid and the solid domains that are thermally coupled to one another. One of the models is a crank angle transient, three-dimensional, multiphase, volume of fluid (VOF) CFD model of the fluid behind the reciprocating piston consisting of the piston jet and crankcase gases. This model is coupled to a piston solid model. The piston motion and heat transfer from the piston to the liner are rigorously accounted for. The combustion heat flux on the piston surface was an input to the current analysis as a boundary condition. All simulations were performed using the commercial CFD software Simerics MP+. The developed method is applied to three DI Diesel engine pistons, one piston without a cooling gallery and two pistons with cooling galleries.

The Society of Automotive Engineers Fatigue Design & Evaluation Committee [SAE FD&E] is actively working on a total life project for weldments, in which the welding residual stress is a key contributor to an accurate assessment of fatigue life. Physics-based welding process simulation and various types of residual stress measurements were pursued to provide a representation of the residual stress field at the failure location in the fatigue samples. A well-controlled and documented robotic welding process was used for all sample fabrications to provide accurate inputs for the welding simulations. One destructive (contour method) residual stress measurement and several non-destructive residual stress measurements-surface X-ray diffraction (XRD), energy dispersive X-ray diffraction (EDXRD), and neutron diffraction (ND)-were performed on the same or similarly welded samples.

This paper details a comprehensive CFD study of all three variants of the DrivAer car geometries: Fastback, Notchback and Estate configurations. The most realistic geometry was chosen for each of the variants; with detailed underbody, wheels and mirrors. In addition to the closed-grille standard DrivAer models, the open-grille variant has also been simulated. Simulations are performed and compared with experiments both with and without ground simulation. Mesh generation was performed without surface alterations (e.g. wrapping) using a novel Binary-Tree automatic unstructured mesher. All simulations were performed using an enhanced k-ε RANS turbulence model within Simerics MP+. A consistent modeling methodology was developed that was rigorously applied to all variants of the DrivAer model and the simulations are shown to have consistently good agreement with experimental measurements.

The increase in computational power in recent times has led to multidimensional computational fluid dynamics (CFD) modeling tools being used extensively for optimizing the diesel engine piston design. However, it is still common practice in engine CFD modeling to use constant uniform boundary temperatures. This is either due to the difficulty in experimentally measuring the component temperatures or the lack of measurements when simulation is being used predictively. This assumption introduces uncertainty in heat flux predictions. Conjugate heat transfer (CHT) modeling is an approach used to predict the component temperatures by simultaneously modeling the heat transfer in the fluid and the solid phase. However, CHT simulations are computationally expensive as they require more than one engine cycle to be simulated to converge to a steady cycle-averaged component temperature.

Single-cylinder engine experiments and computational fluid dynamics (CFD) modeling were used in this study to conduct a comprehensive evaluation of the accuracy of the modeling approach, with a focus on soot emissions. A semi-empirical soot model, the classic two-step Hiroyasu model with Nagle and Strickland-Constable oxidation, was used. A broad range of direct-injected (DI) combustion systems were investigated to assess the predictive accuracy of the soot model as a design tool for modern DI diesel engines. Experiments were conducted on a 2.5 liter single-cylinder engine. Combustion system combinations included three unique piston bowl shapes and seven variants of a common rail fuel injector. The pistons included a baseline “Mexican hat” piston, a reentrant piston, and a non-axisymmetric piston similar to the Volvo WAVE design. The injectors featured six or seven holes and systematically varied included angles from 120 to 150 degrees and hole sizes from 170 to 273 μm.