Search Results

In open-grille vehicle aerodynamics simulation using computational fluid dynamics, in addition to basic flow characteristics, such as turbulent flow with a Reynolds number of several million on the bluff body, it is important to accurately estimate the cooling air flow introduced from the front opening. It is therefore necessary to reproduce the detailed geometry of the entire vehicle including the engine bay as precisely as possible. However, there is a problem of generating a good-quality calculation grid with a small workload. It usually takes several days to a week for the pretreatment process to make the geometry data ‘clean’ or ‘watertight’. The authors proposed a computational method for complex geometries with a hierarchical Cartesian grid and a topology-independent immersed boundary method with dummy cells that discretize the geometry on a cell-by-cell basis and can set an imaginary point arbitrarily.

It has been widely known that thermal and fuel stratifications of in-cylinder mixture are effective to reduce in-cylinder pressure rise rate during high load HCCI operations. In order to optimize a combustion chamber design and combustion control strategy for HCCI engines with wide operational range, it is important to know quantitatively the influence of the temperature and fuel concentration distributions on ignition and heat release characteristics. At the same time, it is important to know the influence of in-cylinder flow and turbulence on the temperature and fuel concentration distributions. In this study, a numerical simulation of HCCI combustion were conducted to investigate the effects of the in-cylinder flow and turbulence, and the distributions of temperature on ignition and combustion characteristics in HCCI combustion.

The critical change in drag occurring on the Ahmed body when the slanted base has an angle of 30° is due to a transition in the wake structure. In a previous study on flow analysis across the Ahmed body, we investigated the unsteady wake experimentally using hot-wire and particle image velocimetry measurements. However, because the experimental analysis yielded limited data, the spatially unsteady wake behaviour, interaction between the trailing vortex and transverse vortices (up/downwash), and flow mechanism near the body were not discussed sufficiently. In this study, the unsteady wake structures were analysed computationally using computational fluid dynamics to understand these issues, and the hypothesis was tested. The slant angle was 27.5°, which is identical to that in the experiment and corresponds to a high drag condition indicated experimentally.

A wall-resolving Large Eddy Simulation (LES) has been performed by using up to 40 billion grids with a minimum grid resolution of 0.1 mm for predicting the exterior hydrodynamic pressure fluctuations in the turbulent boundary layers of a test car with simplified geometry. At several sampling points on the car surface, which included a point on the side window, the door panel, and the front fender panel, the computed hydrodynamic pressure fluctuations were compared with those measured by microphones installed on the surface of the car in a wind tunnel, and effects of the grid resolution on the accuracy of the predicted frequency spectra were discussed. The power spectra of the pressure fluctuations computed with 5 billion grid LES agreed reasonably well with those measured in the wind tunnel up to around 2 kHz although they had some discrepancy with the measured ones in the low and middle frequencies.

The critical change in drag occurs in the Ahmed Body at 30° of the slanted base due to the transition in the wake structure. The distinctive feature of this bi-stage phenomenon, which consists of three-dimensional and quasi-axisymmetric separation states, is that the state drastically changes. Because this feature indicates that each state is stable around a critical angle, the transition is believed to be triggered by some instantaneous disturbances. Therefore, in our previous papers, we have paid attention on the unsteady behavior of the wake to determine the trigger that induces the transition. However, the relationship between the spatial transient behavior of the wake structures and the specific frequencies has not been clarified. Then, we tried to control the degree of interaction of the trailing vortices on the downwash by changing the aspect ratio of the slanted base.

Unresolved issues of Homogeneous Charge Compression Ignition (HCCI) combustion include an extremely rapid pressure rise on the high load side and resultant knocking. Studies conducted to date have examined ways of expanding the region of stable HCCI combustion on the high load side such as by applying supercharging or recirculating exhaust gas (EGR). However, the effect of applying EGR gas to supercharged HCCI combustion and the mechanisms involved are not fully understood. In this study, the effect of EGR gas components on HCCI combustion was investigated by conducting experiments in which external EGR gas was applied to supercharged HCCI combustion and also experiments in which nitrogen (N2) and carbon dioxide (CO2) were individually injected into the intake air pipe to simulate EGR gas components. In addition, HCCI combustion reactions were analyzed by conducting chemical kinetic simulations under the same conditions as those of the experiments.

The objective of this paper is to investigate the potential of lean burn combustion to improve the thermal efficiency of spark ignition engine. Experiments used a single cylinder gasoline spark ignition engine fueled with primary reference fuel of octane number 90, running at 4000 revolution per minute and at wide open throttle. Experiments were conducted at constant fueling rate and in order to lean the mixture, more air is introduced by boosted pressure from stoichiometric mixture to lean limit while maintaining the high output engine torque as possible. Experimental results show that the highest thermal efficiency is obtained at excess air ratio of 1.3 combined with absolute boosted pressure of 117 kPa. Three dimensional computational fluid dynamic simulation with detailed chemical reactions was conducted and compared with results obtained from experiments as based points.

When the planing craft with outboard motor is running, cavitation occurs around the surface of propeller and lower unit of outboard motor. Cavitation has been classified under several categories by the feature and cause of occurrence. Among them, cloud cavitation and root cavitation lead to erosion damage on the surface of lower unit and propeller. To prevent from poor appearance or performance deterioration of outboard motor by erosion damage, it is important problem to predict the erosion occurrence. Currently we can predict the cavitation phenomena sufficiently, but the area of cavitation does not necessarily correspond with the area of erosion. In this study, we present the new method to predict the area of erosion due to cavitation using CFD (computer fluid dynamics) analysis. In order to evaluate the accuracy of erosion occurrence simulation, the simulation results are compared against the result of a full-scale cruising test.

On a bluff body which has a slant surface on the rear upper part, it is well known that the drastic change of a wake structure behind the rear body occurs at 30°of the slant angle. Originally, this critical phenomenon was pointed out by L.J. Janssen, W.H. Hucho, and H.J. Emmelmann in the middle of the 1970s. In 1984, S.R. Ahmed conducted systematic measurements by changing the rear slant angle of the bluff body, called the “Ahmed Body”, to find the critical phenomenon. In the 2000s, D.B. Sims-Williams found that the Ahmed Body had vortex structures which had specific frequencies. However, the relationship between the critical phenomenon and the unsteady behaviour has not been clarified yet. Therefore, as the first step of this study, we measured the unsteady wake behaviour for various slant angles to find the relationship between the Strouhal number and the angle. The characteristics of the fluctuation were captured with two hot-wires.

An air-dam spoiler is commonly used to reduce aerodynamic drag in production vehicles. However, it inexplicably tends to show different performances between wind tunnel and coast-down tests. Neither the reason nor the mechanism has been clarified. We previously reported that an air-dam spoiler contributed to a change in the wake structure behind a vehicle. In this study, to clarify the mechanism, we investigated the coefficient of aerodynamic drag CD reduction effect, wake structure, and underflow under different boundary layer conditions by conducting wind tunnel tests with a rolling road system and constant speed on-road tests. We found that the air-dam spoiler changed the wake structure by deceleration of the underflow under stationary floor conditions. Accordingly, the base pressure was recovered by approximately 30% and, the CD value reduction effect was approximately 10%.

A simulation framework for vehicle aerodynamics using up to 10 billion fully unstructured cells has been developed on a world-fastest class supercomputer, called the K computer, in Kobe, Japan. The simulation software FrontFlow/red-Aero was fully optimized on the K computer to utilize up to 10,000 processors with tens of thousands of cores. A hybrid parallelization method using MPI among processors and OpenMP among cores inside each processor was adopted. The code was specially tuned for unsteady aerodynamic simulation including large-eddy simulation, and low Mach number approximation was adopted to avoid excessive iterations usually required for the fully incompressible algorithm. The automated mesh refining system was developed to generate unstructured meshes of up to 10 billion cells. In the system, users only generate unstructured meshes in the order of tens of millions of cells directly using commercial preprocessing software.

A great deal of interest is focused on Homogeneous Charge Compression Ignition (HCCI) combustion today as a combustion system enabling internal combustion engines to attain higher efficiency and cleaner exhaust emissions. Because the air-fuel mixture is compression-ignited in an HCCI engine, control of the ignition timing is a key issue. Additionally, because the mixture ignites simultaneously at multiple locations in the combustion chamber, it is necessary to control the resultant rapid combustion, especially in the high-load region. Supercharging can be cited as one approach that is effective in facilitating high-load operation of HCCI engines. Supercharging increases the intake air quantity to increase the heat capacity of the working gas, thereby lowering the combustion temperature for injection of the same quantity of fuel. In this study, experiments were conducted to investigate the effects of supercharging on combustion characteristics in an HCCI engine.

The anodic oxide films are formed to improve the corrosion resistance on aluminum alloy that used as the parts of engines and car bodies. Because these films are porous structure, it is necessary to seal the pores to further improve the corrosion resistance. The pores are sealed with hydrated alumina by treating the films in boiling water or solution that added sealing additives. These hydration sealing has a problem that energy consumption is large because of long sealing time and high temperature of solution. In this study, the authors have developed a new sealing treatment (Lithium sealing) using a lithium hydroxide solution to solve above problem. Lithium sealing mainly sealed the pores with lithium aluminate double salt (LiH(AlO2)2·5H2O). This salt was rapidly formed in strong alkaline solution at room temperature, so that the sealing time was reduced to about 1/10 compared with the conventional sealing.

In this study, to improve the cruising performance of planing craft with outboard motor, we have examined a estimation method of the hull attitude angle at cruising and resistance in case of changing the tilt angle and mounting position of the outboard motor by the tank test using a scale model of a hull and an outboard motor in the ship testing tank. Planing craft with outboard motor have different characteristics from large vessels. The characteristics are shown below. The hull attitude angle at cruising is different in each forward speed. The thrust accounted for a large percentage of hull weight. And the flow field around the hull changes along with the operation of the propeller. The hull attitude angle at cruising is changed by the rigging state of the outboard motor.

Anodizing is applied to improve the durability and the corrosion resistance of aluminum alloy parts of engines and car bodies. Generally, anodic oxide film is formed using direct current anodizing (DCA). However, in the case of anodizing high silicon aluminum alloy cast parts, it is difficult to derive uniform film thickness distribution. Furthermore, it takes a long treatment time which causes low productivity. In this study, the authors have developed an anodizing method by using high-frequency switching anodizing (HSA) to solve these problems. The growth process of anodic oxide film is susceptible to the metallographic structure. Thus, the typical DCA application to the high silicon aluminum alloy produces a non-uniform film thickness, while HSA has the potential to form uniform film without being affected by metallographic structure. Moreover, the current density of HSA is higher than that of DCA which reduces treatment time to 1/5 as the film formation enhances.

We have developed a small-displacement gasoline direct-injection engine (1.3L). Gasoline direct-injection engines rely on ultra-lean stratified combustion to deliver significantly better fuel economy, and are already used in many practical applications. When gasoline direct-injection is applied to a small-displacement engine, however, the amount of wall wetting of fuel on the piston surface will increase because the traveled length of the fuel spray is short. This may result in problems such as smoke production, high emissions of unburned HC, and poor combustion efficiency.

The purpose of this study was to find compatible specifications both of emission reduction and high power output with good throttle response for a sports utility motorcycle. In the emission reduction challenge, we examined equipping the exhaust system with a catalytic converter to achieve sufficient emission reduction. The catalytic converter, however, caused a temperature rise in the exhaust system, which caused a pressure propagation change. Additional muffler design optimization effectively maintained high performance and acceleration. The exhaust valve device was also optimized for emission reduction and high power output over a wide engine speed range. The optimized control of the exhaust valve was beneficial to preventing short-circuit of fresh mixture gas and early activation of the catalyst. Such comprehensive specifications could satisfy the performance and driveability characteristics required for sports utility motorcycles.

The Emission Regulations for Motorcycles in Japan was put into effect in October 1998 with the goal of reducing the total hydrocarbon emissions from motorcycles in the country to around 50% of the present amount. These regulations initiated a need to develop emission-converting catalysts, having the three characteristics written below, for two-stroke engines that historically have produced more hydrocarbons than four-stroke engines: 1 High performance of hydrocarbon conversion 2 High light-off performance 3 High thermal stability under high temperature Among a number of catalytic adjustment methods, the loading method of precious metals and the washcoat preparing method were modified to realize mass production of high-performance, low-cost catalysts.

The purpose of this study is to experimentally investigate in-cylinder flows with cyclic variation in a practical part-loaded two-stroke engine. First, the in-cylinder LDV measurements are introduced, which were carried out above the port layout and the combustion chamber as well as the exhaust pipe or the transfer port together with the simultaneous pressure measurements. Second, the in-cylinder flow characteristics in different combustion groups were discussed. The in-cylinder flow and the combustion-chamber flow were not simply characterized by the pressure variation in the engine or the other passage flow in the exhaust pipe or the transfer port. Finally, the in-cylinder flow structure with three stages was shown using the vector variation analysis and the drawing of the velocity profiles in the engine parts.