Refine Your Search

Topic

Search Results

Viewing 1 to 10 of 10
Technical Paper

Development of Hose and Pipe Assembly for Automatic Transmission Cooling System

2019-01-09
2019-26-0327
Rubber hose and metallic pipe with crimped joints are extensively used in steering system assembly, transmission oil cooler system, brake system etc. to carry hydraulic fluid or lubricants from one place to another. The pipe and rubber hose assembly provides necessary flexibility for complex routing on the vehicle level. Design of hose and pipe assembly for this application are different due to difference in operating pressure and temperature requirement for vehicle application. This paper defines the criteria for design and validation of hose & pipe assembly used to connect automatic transmission with the cooler. Crimped joints are validated for their separation force, leakages, ability to withstand pressure pulsations, burst test etc. Parameters which influence the hose & pipe assembly durability are pipe end flaring dimensions, type of crimping, reinforcement type, its size, material and pattern, rubber material properties, crimping force, effective crimping diameter etc.
Technical Paper

Electro-Magnetic Parking Brake System for Electric Vehicles

2019-01-09
2019-26-0119
Regular vehicle has the advantage of Engine resistance even when it is not fired, hence chances of vehicle roll back on gradients will be minimized. This is not the case for Electric vehicles, which uses an electric motor that does not have any resistance offered to wheels that prevent vehicle roll back on gradient. This leads to increased load on the conventional hydraulic brakes due to absence of engine inertia. Hence, there is a need for a low cost and reliable automatic braking system which can help in holding the vehicle and assists the driver during launch in case he need to stop at a gradient. An Electromagnetic brake (EM brake) system can be used as a solution for the above-mentioned requirement. EM brake can provide hill hold and hill assist effect in addition to automatic parking brake application when the vehicle is turned-off. This system will assist anyone who need to halt the vehicle at a gradient and then relaunch it without much struggle.
Technical Paper

Modeling and Optimization of Pneumatic Brake System for Commercial Vehicles by Model Based Design Approach

2017-09-17
2017-01-2493
Apart from being an active safety system the brake system represents an important aspect of the vehicle dynamics. The vehicle retardation and stopping distance completely depend upon the performance of brake system and the functionality of all components. However, the performance prediction of the entire system is a challenging task especially for a complex configuration such as multi-axial vehicle applications. Furthermore, due to its complexity most often the performance prediction by some methods is limited to static condition. Hence, it is very important to have equivalent mathematical models to predict all performance parameters for a given configuration in all different conditions This paper presents the adopted system modelling approach to model all the elements of the pneumatic brake system such as dual brake valve, relay valve, quick release valve, front and rear brake actuators, foundation brake etc.
Technical Paper

Transient 1D Mathematical Model for Drum Brake System to Predict the Temperature Variation with Realistic Boundary Conditions

2017-01-10
2017-26-0299
Brake system is the most important system in the vehicle considering the overall vehicle safety and speed control. Brake applications are repetitive during a city traffic and hilly terrain on downhill gradient. Frequent braking gives rise to an overheating of the brake drum and its components. Braking operations at high temperature gives rise to problems like reduced deceleration due to loss of brake pad friction characteristics, pad softening and sticking to drum, pad distortion and wear etc. All these factors collectively result in deterioration of the braking performance and reduction of brake pad durability with time. Till date most of the thermal analysis performed for brake drum heating are through physical testing using brake system prototypes and by means of CFD tools. These methods are time consuming and expensive. There is a need for an alternative method to reduce physical trials and prototype building and reduce dependency on CFD analysis.
Technical Paper

Analysis of Automotive Control Pedals Ergonomics through Mathematical Modelling Based on Human Anthropometry

2017-01-10
2017-26-0252
Vehicle Ergonomics is one of the most vital factor to be considered in vehicle design and development, as the customer wants a comfortable and performance oriented vehicle. An uncomfortable driving posture can lead to painful driving experiences for longer hauls. The control pedals viz. Accelerator, Brake and clutch pedal (ABC Pedals), are the most frequently used parts in the vehicle, their proper positioning with respect to human anthropology is of prime importance, from driver comfort viewpoint. The methodology currently used for optimizing ergonomics with respect to the positioning of pedals in a vehicle included; measuring anthropometric angles manually with the help of H-Point Machine, subjective jury analysis and through software like RAMSIS, JACK, etc. Manual measurement doesn’t give the flexibility of iterations for optimization. The subjective analysis is based on insinuations thereby, cannot be standardized.
Technical Paper

Air Compressor Duty Cycle Reduction in Passenger Bus Application

2015-04-14
2015-01-0139
Today urban buses are equipped with more air consuming devices for an example pneumatic doors, exhaust brake, air suspension and in SCR system to name a few. This has resulted in higher air demand leading to high compressor duty cycles which cause conditions (such as higher compressor head temperatures) that may adversely affect air brake charging system performance. These conditions may require additional maintenance due to a higher amount of oil vapor droplets being passed along into the air brake system. Factors that add to the duty cycle are air suspension, additional air accessories, use of an undersized compressor, frequent stops, excessive air leakage from fittings, connections, lines, chambers or valves, etc. This paper discussed about methodology used to reduce air consumption of air consuming devices used in urban bus application. Performance assessment of air consuming devices with minimum available air pressure was conducted and found satisfactory.
Technical Paper

Innovative Concept of Front Disc Brake Module with Weight Reduction and Cost Optimisation

2014-09-28
2014-01-2505
The customer satisfaction index is higher for disc brake systems because of the advantages like less reaction time, shorter stopping distance and improved pedal feel compared to drum brake system. In current competitive market scenario and as per customer requirements, front disc brake module is becoming necessary. The brake system design is challenging task due to stringent performance meeting criteria and packaging constraints with weight optimization. Brake disc is very important component in the brake system which is expected to withstand high braking torque and dissipate heat during braking event. In existing car to replace front drum brake with disc brake module, vehicle needs to undergo legislative verifications and certifications with respect to pedal effort, stopping distance and circuit failed conditions etc.
Technical Paper

Practical Approach for Vehicle HVAC Noise Reduction and Comfort Improvement

2011-05-17
2011-01-1592
Comfortable cabin environment from temperature, noise and vibration point of view is one of the most desirable aspects of any vehicle operating in hot or cold environment. Noise generated from HVAC system is one of the most irritating phenomena resulting in customer dissatisfaction and complaints. It becomes absolutely necessary to have low HVAC noise levels when the target market has hot weather all round the year. Balance between control of temperature in desired way with least possible noise and vibration is the key for HVAC performance optimization within constrains posed by design and cost. This paper describes the approach for NVH refinement of front HVAC system proposed for a vehicle with limited off-road capability for which packaging constraints and late changes related to airflow and HVAC unit design for meeting comfort and crash requirements resulted in deterioration of noise and vibrations while operation.
Technical Paper

Optimization of Brake Pedal Feel and Performance for Dual Air Over Hydraulic System on Light Commercial Vehicles

2010-10-05
2010-01-1888
In current scenario, Light Commercial Vehicle segment (7 ton - 9.6 ton) is gradually experiencing a shift in the focus from being just a goods carrier to a vehicle which is developed to take care of driver's safety and comfort in terms of better ergonomics and aesthetics. As compared to their conventional counterparts the new generation Light Commercial Vehicles are better equipped and tuned to cater to the changing needs of the consumers. In view of this, refinement at the sub system level is becoming far more critical. On the same lines, the present work discusses a refined brake system for Light Commercial Vehicles where the conventional pneumatic system is replaced with Dual Air Over Hydraulic (DAOH) to achieve cost and weight advantages without compromising on its performance. However, during the development process, a lot of issues were observed with respect to the braking performance and the brake pedal feel.
Technical Paper

Cost Effective High Strength Electric Resistance Welded Tubes For Structural Applications

2010-10-05
2010-01-1912
The properties of Cold drawn electric resistance welded, as drawn (CEW-AD) tubes and Electric resistance welded (ERW) tubes are vastly different. Deformation resistance of ERW tube is less than half that of CEW-AD tube, hence not preferred for structural applications, common practice being the use of CEW-AD tubes for Chassis cross members in vehicles. A new cost effective high strength ERW tube was developed which has been proved to be superior to the currently used CEW-AD tubes in terms of mechanical properties, formability, consistency and uniformity of the properties over the tube length. The newly developed tube through use of special micro alloy grade in ERW has made it possible to eliminate some of the manufacturing processes like annealing, phosphating, cold drawing etc. which has led to considerable cost saving.
X