Search Results

The mechanism of lubricant dilution by post injection fuel in a diesel engine was investigated. The operating conditions of the engine were changed, and oil was sampled from each part of the piston and the crankcase, and the dilution ratio was analyzed. Also, photochromism was used to visualize the oil and fuel flow. Dilution ratios obtained from oil sampling and photochromism showed the same tendency.

As electric powertrain for electric vehicles (EVs) and hybrid vehicles (HVs) are becoming more efficient and smaller, rolling bearings for these vehicles should be capable of operating at higher speeds than those for internal combustion engines (ICEs). One key factor in predict fatigue endurance of such bearings is the oil film thickness on the bearing raceway grooves. Direct measurement of the oil film in operating machines is virtually unfeasible, while calculation of the oil film requires the input of precise temperature variation around the film. In this study, the oil film thickness on the bearing raceway grooves was calculated while in high-speed rotation by: (1) measuring the temperature profile of the bearing raceway outer ring; (2) calculating the temperature of the raceway groove using the basic formula for heat transfer; and (3) conducting an Elasto-Hydrodynamic Lubrication (EHL) analysis based on the temperature calculated in (2).

Clarifying the mechanism of oil transporting upward at around an oil ring of a piston is necessary for calculating engine oil consumption. This study aimed to clarify the function of oil drain holes in the oil ring groove of a piston. The effect of the oil drain holes in the groove on oil consumption was investigated. Also the pressure balance around the oil ring was measured. It was found that the drain holes in the groove lowered oil consumption. It was assumed that lower pressure in the groove with the drain holes caused less oil flow into the third land.

The friction reduction of a piston/piston-ring assembly is effective for fuel economy of an engine, and a friction measurement method is required for developing low friction pistons, piston-rings and lubricants. Most suitable method for friction measurement for piston assemblies is “floating liner method”. It has load sensors between a floating cylinder liner and cylinder block, and the sensors can detect friction force acting on the liner. Many apparatuses using floating liner method are developed. They are roughly divided to two categories. In one of them, floating liner is supported by load-washers which axis is set parallel to the center line of the cylinder liner. In another type, floating liner is supported by three-component force sensors installed on the side face of the cylinder. In this paper, five types of floating liner devices were compared.

The piston rings, the engine sliding parts, are required to further contribute on mechanical loss reduction in order to improve fuel efficiency. However, many cases of the abnormal combustion due to oil upward flow, as well as the increase in oil consumption have been reported. Therefore, elucidation of the mechanism of those phenomena is still an urgent task. It is widely known that the distribution of the sliding face pressure in between the piston ring and the cylinder bore largely influence the oil flow via the sliding face of the piston ring. However, there are many unknown aspects in this field. Therefore, verification of the sliding face pressure during the actual operation is necessary in order to elucidate the mechanism of oil consumption. The thin-film sensor, since it has little influence on shape, is widely used as a measurement method of the sliding face pressure between two different faces, however this method has never been applied to the piston ring in the past.

In order to develop various parts and components for hybrid electric vehicles, understanding the effect of their structure and thermal performance on their fuel consumption and cruising distance is essential. However, this essential information is generally not available to suppliers of vehicle parts and components. In this report, following a previous study of electric vehicles, a simple method is proposed as the first step to estimate the algorithm of the energy transmission and then the cruising performance for hybrid electric vehicles. The proposed method estimates the cruising performance using only the published information given to suppliers, who, in general, are not supplied with more detailed information. Further, an actual case study demonstrating application of the proposed method is also discussed.

For various densities of gas jets including very light hydrogen and relatively heavy ones, the penetration length and diffusion process of a single high-speed gas fuel jet injected into air are computed by performing a large eddy simulation (LES) with fewer arbitrary constants applied for the unsteady three-dimensional compressible Navier-Stokes equation. In contrast, traditional ensemble models such as the Reynolds-averaged Navier-Stokes (RANS) equation have several arbitrary constants for fitting purposes. The cubic-interpolated pseudo-particle (CIP) method is employed for discretizing the nonlinear terms. Computations of single-component nitrogen and hydrogen jets were done under initial conditions of a fuel tank pressure of gas fuel = 10 MPa and back pressure of air = 3.5 MPa, i.e., the pressure level inside the combustion chamber after piston compression in the engine.

In order to develop various parts and components of electric vehicles, understanding the effects of their structures and thermal performance on the energy consumption and cruising distance is important. However, such essential and detailed information is generally not always available to suppliers of vehicle parts and components. This paper presents the development of a simple model of the energy consumption by an electric vehicle in order to roughly calculate the cruising performance based only on the published information to give to suppliers, who otherwise cannot obtain the necessary information. The method can calculate the cruising distance within an error of 4% compared to the published information. The effects of the glass and body heat transfer characteristics on the cruising performance in winter were considered as an example application of the proposed model.

A simple method is frequently used to calculate a reciprocating engine’s bearing load from the measured cylinder pressure. However, it has become apparent that engine downsizing and weight reduction cannot be achieved easily if an engine is designed based on the simple method. Because of this, an actual load on a bearing was measured, and the measured load values were compared with a bearing load distribution calculated from cylinder pressure. As a result, it was found that some of actual loads were about half of the calculated ones at certain crank angles. The connecting rod’s elastic deformation was focused on as a factor behind such differences, and the rod’s deformation due to the engine’s explosion load was studied. As a result, it was found that the rod part of the engine’s connecting rod was bent by 0.2 mm and became doglegged. Additional investigation regarding these findings would allow further engine downsizing.

1 Piston design approach for automotive engines has been advanced from both experimental and calculation analysis. However, the developments of experimental analysis method that can verify the accuracy of the calculation analysis are required. In this paper, multi-point thin-film pressure sensor for piston pin-boss part (hereinafter pin-boss) was sputtered on piston pin sliding surface and oil-film pressure distribution was measured in axial and circumferential direction using the pin-boss fatigue tester. Two kinds of pistons with different pin-boss shape (tapered shape) were used in the experiment. The peak pressure of piston with large tapered shape was higher about 20%, compared to the piston with the small tapered shape. As a result of oil film pressure distribution in circumferential direction, it has measured that the oil-film pressure at near side relief was higher than that of piston top side.

The reduction of friction losses is a subject of central importance in a diesel engine. The piston frictions of low viscosity engine oil and molybdenum dialkyl dithiocarbamate (MoDTC) have been measured by floating liner method. It was found that the low viscosity engine oil lower than 5W-30 is not effective against the reduction of friction mean effective pressure (FMEP) related to the fuel consumption. MoDTC showed a good performance against the reduction of FMEP. In the friction measurement points, the reduction ratio of 10W-30 with MoDTC to 10W-30 was greater than that of 5W-30 to 10W-30.

The improvement of fuel consumption is the most important issue for engine manufactures from the viewpoint of energy and environment conservation. A piston-cylinder system plays an important role for the reduction of an engine friction. For the improvement of the frictional behavior of the piston-cylinder system, it is beneficial to observe and analyze the frictional waveforms during an engine operation. To meet the above-mentioned demand, frictional waveforms were measured with using the renewed floating liner device. In the newly developed floating liner device, an actual cylinder block itself was used as a test specimen. The measured single cylinder was an aluminum monolithic type made of hypereutectic Al-17%Si alloy using a high pressure die casting process. The combined piston was a light weight forged piston and a DLC coated piston ring was used. For the measurement, 110cc air cooled single cylinder engine was used.

In the present study, numerical simulation coupling convection and radiation in vehicle was done to analyze the formation of the temperature field under the non-uniform thermal condition. The scaled cabin model of simplified compact car was used and the thermal condition was determined. The fore floor, the top side of the inst. panel, the front window and the ceiling were heat source. The lateral side walls were cooled by the outdoor air and the other surfaces were adiabatic. It is same with the experimental condition presented in Part 5. In order to analyze the individual influence of each heat source, Contribution Ratio of Indoor climate (CRI) index was used. CRI is defined as the ratio of the temperature rise at a point from one individual heat source to the temperature rise under the perfect mixing conditions for the same heat source.

Accuracy of numerical simulation has to be evaluated through the actual phenomenon such as experiment or measurement and then it can be employed to design the air-conditioning system of car cabin at the development phase. Scaled model of vehicle cabin was created by the Society of Automotive Engineers of Japan (JSAE) and the experiment was performed to obtain the detailed information of heat transfer characteristics inside the cabin under the non-isothermal condition. The sheet heaters were put to the inner surface of the acrylic cabin and they supplied certain amount of heat. The temperatures of inner and outer surface and air were measured to evaluate the thermal environment of the cabin. The results lead to enhancement of the data of the standard model of the cabin.