Refine Your Search

Topic

Affiliation

Search Results

Technical Paper

Test and Analysis of Electromagnetic Noise of an Electric Motor in a Pure Electric Car

2019-06-05
2019-01-1492
Compared with the low-frequency ignition order of mechanical and combustion noise of an internal combustion engine, the noise of electric drive assembly of electric vehicles is mainly the high-frequency whining noise generated by electromagnetic forces of motors and gear meshing of reducers, as well as the high-frequency umbrella-shape noise generated by DC/AC pulse width modulation. Although the radiated sound power of these high frequency noise is far less than that of an internal combustion engine, the high frequency noise of the motor and the reducer is subjectively quite annoying. This paper studies the characteristics of electromagnetic noise of a permanent magnet synchronous motor in an electric car. By testing and analyzing of noise sources of an electric motor in the car and on a test rig, the spatial order characteristics and amplitude-frequency characteristics of the electromagnetic forces are revealed. The noise orders are multiples of the number of motor poles.
Technical Paper

Sound Quality Prediction Modelling for the Transient Sound of Vehicle Door Latch Closure

2019-06-05
2019-01-1517
Door latch closure noise has contribution on sound quality of vehicle door slam sound. This paper focuses on the modelling of sound quality for door latch closure sound. 24 various latch closure sound samples were recorded to be evaluated subjectively. A novel Dynamic Paired Comparison Method (DPCM) was introduced for subjective evaluation. By eliminating the redundant comparison pairs the DPCM dramatically reduced the evaluation work load comparing to the traditional Paired Comparison Method (PCM). Correlation between subjective evaluation results and psychoacoustic metrics was analyzed to find out the most relevant metrics as inputs for the subsequent prediction model. Besides, the shudder effect induced by multi-impact of latch components during closing movement was also found strongly affecting the subjective perception of door latch closure sound.
Technical Paper

Performance Testing and Analysis of Multi-Channel Active Control System for Vehicle Interior Noise Using Adaptive Notch Filter

2019-06-05
2019-01-1567
It is considered that slow convergence speed and large calculation amount of commonly used adaptive algorithm in the active control system for vehicle interior noise yield noise reduction performance and hardware requirements problems. In this paper, a 4-channel active control of vehicle interior noise based on adaptive notch filter is established, and road test is carried out to test and analyze the performance of the control system. Firstly, the general mathematic model of the multi-channel active control system based on adaptive notch filter is established. The computational complexity of the algorithm is analyzed and compared with that of the FXLMS algorithm. Secondly, a hardware-in-the-loop test bench based on multi-channel adaptive notch filter is set up, to measure the noise reduction performance of ANC system under various working conditions.
Technical Paper

Pressure Estimation Algorithms in Decoupled Electro-Hydraulic Brake System Considering the Friction and Pressure-Position Relationship

2019-04-02
2019-01-0438
This paper presents several pressure estimation algorithms (PEAs) for a decoupled electro-hydraulic brake system (EHB), which is driven by an electric motor + reduction gear. Most of the pressure control solutions are based on standard pressure-based feedback control, requiring a pressure signal. Although the pressure sensor can produce the pressure feedback signal, it will increase cost and enlarge installation space. The rotation angle of electric motor is available by the built-in sensor, so the pressure can be estimated by using the rotation angle. Considering the typical nonlinearities (i.e. friction, pressure-position relationship) and uncertainties (i.e. disturbance caused by friction model), the estimation-oriented model is established. The LuGre model is selected to describe the friction, and the pressure-position relationship is fitted by a quadratic polynomial.
Technical Paper

Security Mechanisms Design of Automotive Gateway Firewall

2019-04-02
2019-01-0481
Automotive security has become one of important topics in recent years under new automotive Electronic and Electrical Architecture (EEA). With the development of Intelligent Connected Vehicle (ICV), it has become possible to hack an automotive through in-vehicle networks. The introduction of Information Communications Technology (ICT) brings more risk threats to automotive. Researchers have shown that an attacker can easily tamper with many automotive functions via On-Board Diagnostic II (OBD-II) or In-Vehicle Infotainment (IVI). In order to protect automotive against malicious attacks, automotive security risks were analyzed and then security mechanisms based on network firewall were designed in this paper. Automotive network firewall is a security system that monitors and controls incoming and outgoing network traffics of automotive based on predetermined security rules. The main functions of network firewall include packet filter, anti-DoS and access control.
Technical Paper

Parameters Analyses and Identification for Rubber Bush Based on Theoretical Dynamic Model with Effects of Temperature and Preload

2019-04-02
2019-01-1272
A series connection of the KVBC (Kelvin-Voigt and Bouc-wen) theoretical model of rubber bush in automobile suspension is established. The numerical calculation model is also developed through Matlab/simulation and 9 parameters are identified. Experiments are conducted on the rubber bush on a bench for dynamic and static characteristics and to supply appropriate and reliable data for parameter identification. Based on this, preload and temperature are taken into consideration in an ordinary KVBC model as two important additional factors. As a result, it leads to developing a novel model with new parameter identification, which is validated under different conditions. This new modeling method of rubber bush has three advantages. First, it shows improved accuracy for solving non-linear problems in a multi-body calculation, which is useful for researchers and vehicle engineers.
Technical Paper

Combined Technologies for Efficiency Improvement on a 1.0 L Turbocharged GDI Engine

2019-04-02
2019-01-0233
The CO2 reduction request for automotive industry promotes the efforts on the engine thermal efficiency improvement. The goal of this research is to improve the thermal efficiency on an extremely downsized 3-cylinder 1.0 L turbocharged gasoline direct injection engine. Effects of compression ratio, exhaust gas recirculation (EGR), valve timing and viscosity of oil on fuel economy were studied. The results show that increasing compression ratio, from 9.6 to 12, can improve fuel economy at relative low load (below 12 bar BMEP), but has a negative effect at high load due to increased knock intensity. EGR can significantly reduce the pumping loss at low load, optimize combustion phase and reduce exhaust gas temperature. Therefore, the fuel consumption is reduced at all test points. The average brake thermal efficiency (BTE) benefit percentage is 3.47% with 9.6 compression ratio and 5.33 % with 12 compression ratio.
Technical Paper

Genetic Algorithm-Based Parameter Optimization of Energy Management Strategy and Its Analysis for Fuel Cell Hybrid Electric Vehicles

2019-04-02
2019-01-0358
Fuel cell hybrid electric vehicles (FCHEVs) composed of fuel cells and batteries can improve the dynamic response and durability of vehicle propulsion. In addition, braking energy can be recovered by batteries. The energy management strategy (EMS) for distributing the requested power through different types of energy sources plays an important role in FCHEVs. Reasonable power split not only improves vehicle performance but also enhances fuel economy. In this paper, considering the power tracking control strategy which is widely adopted in Advanced Vehicle Simulator (ADVISOR), a constrained nonlinear programming parameter optimization model is established for minimizing fuel consumption. The principal parameters of power tracking control strategy are set as the optimized variables, with the dynamic performance index of FCHEVs being defined as the constraint condition. Then, the genetic algorithm (GA) is applied in the control strategy design for solving the optimization problem.
Technical Paper

A Lattice Boltzmann Simulation of Gas Purge in Flow Channel with Real GDL Surface Characteristics for Proton Exchange Membrane Fuel Cell

2019-04-02
2019-01-0389
Gas purge is considered as an essential shutdown process for a PEMFC (Proton Exchange Membrane Fuel Cell), especially in subfreezing temperature. The water flooding phenomenon inside fuel cell flow channel have a marked impact on performance in normal operating condition. In addition, the residual water freezes in the subzero temperature, thus blocking the mass transfer from flow channel to porous media. Therefore, the gas purge course is of primary importance for improvement of performance and durability. The water droplet residing in the flow channel can be purged out due to shearing force of gas. In fact, the flow channel is not completely flat due to surface roughness of gas diffusion layer (GDL), meaning the water droplet may climb over obstacles. Moreover, the water droplet may block the flow channel and then be sheared into films on the surface of GDL.
Technical Paper

Development of Hardware and Software for On-Board Hydrogen System

2019-04-02
2019-01-0377
The fuel cell engine is considered to be the ultimate technical direction for the development of vehicle power. The on-board hydrogen supply system is important in fuel cell system. However, the on-board hydrogen supply system is diversified, and the management is mostly integrated in the engine controller. Thus, the fuel cell engine controller is excessive coupled with design of on-board hydrogen supply system. In order to improve the portability and compatibility of the fuel cell engine controller, an independent controller of the on-board hydrogen supply system is designed. Meanwhile, the hardware and software are developed to control 35Mpa gaseous hydrogen storage system. After being tested in a high-pressure environment, the controller can detect temperature, pressure and ambient hydrogen concentration of the hydrogen supply system. Simultaneously, it can drive and control the hydrogen cylinder valve.
Technical Paper

Research on Control Algorithm of Air Supply System for High-Pressure PEMFC Engine

2019-04-02
2019-01-0379
The Proton Exchange Membrane Fuel Cell (PEMFC) is the most widely used engine in fuel cell vehicles. For PEMFC, whether the supply of oxygen for cathode is adequate or not is a critical factor for its net output power and service life, and the proper control of air supply mass flow and pressure can effectively improve its system performance and efficiency. At present, fuel cells need to reduce the mass and volume and increase the power density. Therefore, it is necessary to increase the air supply pressure for PEMFC. But at the same time, many auxiliary devices are appended to the system to provide high-pressure air, such as air compressor, intercooler, and back pressure valve, which make the control of the entire air supply system very complicated. So an excellent control algorithm is needed.
Technical Paper

DC/DC Modeling and Current Harmonic Analysis in Fuel Cell Hybrid Power System

2019-04-02
2019-01-0375
Fuel cells directly convert the energy stored in hydrogen into electrical energy through an electrochemical reaction, and the only reaction product is water, which can improve the energy efficiency and reduce the pollution caused by fossil fuels. The fuel cell hybrid power system used in vehicles usually consists of a fuel cell stack and a power battery module, and the DC/DC converter is the key component to connect them together. The current ripples caused by the system have been confirmed to have detrimental effects on the fuel cell’s reliability and lifespan. In addition, it is one of the key factors that reduce the system efficiency. So, it is necessary to analyze the current ripple in the system and maintain it at a low level. In this paper, a brief review on the different kinds of converters used in vehicles has been made. Then, with the help of MATLAB/SIMULINK, a simulation model of the hybrid power system based on 4-phase interleaved parallel topology is established.
Technical Paper

Numerical Analysis and Optimization Design of a Centrifugal Compressor’s Volute for PEM Fuel Cell Vehicle

2019-04-02
2019-01-0376
Centrifugal compressors used in polymer electrolyte membrane fuel cell systems are different from turbochargers in internal combustion engines, because they are required to work at high speed, low mass flow rate, narrow range which nears surge boundaries. In order to meet these requirements, a centrifugal compressor’s volute is designed, analyzed and optimized on its cross-section area, shape of volute tongue and tapered angle of exit. The numerical results show that surge boundary of the compressor is influenced by spiral area significantly and that volute tongue has a major impact on aerodynamic performances at high mass flow rates.
Technical Paper

Online Flooding and Dehydration Diagnosis for PEM Fuel Cell Stacks via Generalized Residual Multiple Model Adaptive Estimation-Based Methodology

2019-04-02
2019-01-0373
For proton exchange membrane fuel cell (PEMFC) stack, critical issues such as flooding and dehydration, are caused by improper water management. With respect to the water management failure, PEMFC stack outputs power and efficiency decreased. Therefore, proper water management with diagnosis contributes to the reliability and durability. Existing researches establish Electrochemical Impedance Spectroscopy (EIS) measurement to detect and identify different faults, whereas the sophistication, overwhelmed computational consumption of EIS and unaffordable dedicated instrumentation make it’s unsuitable for commercial application. Therefore, EIS is not considered to be a viable solution to online and real-time diagnostic scheme. In this paper, an innovative method based on EIS, is further developed to identify some critical PEMFC fault conditions online, wherein generalized residual multiple model adaptive estimation (GRMMAE) methodology is applied.
Technical Paper

Tracking of Extended Objects with Multiple Three-Dimensional High-Resolution Automotive Millimeter Wave Radar

2019-04-02
2019-01-0122
Estimating the motion state of peripheral targets is a very important part in the environment perception of intelligent vehicles. The accurate estimation of the motion state of the peripheral targets can provide more information for the intelligent vehicle planning module which means the intelligent vehicle is able to anticipate hazards ahead of time. To get the motion state of the target accurately, the target’s range, velocity, orientation angle and yaw rate need to be estimated. Three-dimensional high-resolution automotive millimeter wave radar can measure radial range, radial velocity, azimuth angle and elevation angle about multiple reflections of an extended target. Thus, the three-dimensional range information and three-dimensional velocity information can be obtained. With multiple three-dimensional high-resolution automotive millimeter-wave radar, it is possible to measure information in various directions of a target.
Technical Paper

Distributed Drive Electric Vehicle Longitudinal Velocity Estimation with Adaptive Kalman Filter: Theory and Experiment

2019-04-02
2019-01-0439
Velocity is one of the most important inputs of active safety systems such as ABS, TCS, ESC, ACC, AEB et al. In a distributed drive electric vehicle equipped with four in-wheel motors, velocity is hard to obtain due to all-wheel drive, especially in wheel slipping conditions. This paper focus on longitudinal velocity estimation of the distributed drive electric vehicle. Firstly, a basic longitudinal velocity estimation method is built based on a typical Kalman filter, where four wheel speeds obtained by wheel speed sensors constitute an observation variable and the longitudinal acceleration measured by an inertia moment unit is chosen as input variable. In simulations, the typical Kalman filter show good results when no wheel slips; when one or more wheels slip, the typical Kalman filter with constant covariance matrices does not work well. Therefore, a gain matrix adjusting Kalman filter which can detect the wheel slip and cope with that is proposed.
Technical Paper

Model-Based Pitch Control for Distributed Drive Electric Vehicle

2019-04-02
2019-01-0451
On the dual-motor electric vehicle, which is driven by two electric motors mounted on the front and rear axles respectively, longitudinal dynamic control and electro-dynamic braking can be achieved by controlling the torque of front and rear axle motors respectively. Suspension displacement is related to the wheel torque, thus the pitch of vehicle body can be influenced by changing the torque distribution ratio. The pitch of the body has a great influence on the vehicle comfort, which occurs mainly during acceleration and braking progress. Traditionally active suspension is adopted to control the pitch of body. Instead, in this paper an ideal torque distribution strategy is developed to limit the pitch during acceleration and braking progress. This paper first explores the relationship between the torque distribution and the body pitch through the real vehicle test, which reveals the feasibility of the vehicle comfort promotion by optimizing the torque distribution coefficient.
Technical Paper

Influence Mechanism of Electromechanical Parameters on Transient Vibration of Electric Wheel System

2019-04-02
2019-01-0462
Electric wheel systems of in-wheel motor driven vehicles consist of the motor controller, in-wheel motor and tire-suspension assembly. The coupling between the electromagnetic excitation and elastic structure gives rise to electromechanical dynamic issues. As for the structural layout of the electric wheel system, the driving motor is directly connected to the wheel without torsion dampers or transmission in the driveline, thus making the electric wheel structure a weak damping system. Moreover, the driving torque of electric wheel can change rapidly in various conditions of vehicle. As a result, the transient vibration problem becomes one of the key electromechanical dynamic issues in the electric wheel system. To investigate this problem, the electromechanical coupling model of the electric wheel system is established first. Then the transient responses of the electric wheel under abrupt changes of the driving torque are simulated.
Technical Paper

Analysis of the Statistical Energy Consumption and Its Application to an Economic Evaluation of Plug-In Hybrid Electric Vehicles

2019-04-02
2019-01-0933
The energy consumption depends not only on the structures of vehicles but also on their operating conditions. For vehicles with the same structure, the operating conditions will vary from driver to driver. In this paper, considering the difference of operating conditions, the concept of statistical energy consumption is proposed to reveal the statistical law of actual vehicle energy consumption. In this paper, a plug-in hybrid electric vehicle (PHEV) is taken as the research object. Based on the distribution law of three vehicle use factors, i.e. vehicle mass, daily driving distance and driving aggression, Monte Carlo method is used to simulate and calculate the statistical energy consumption and statistical comprehensive energy consumption. Then, the energy consumption values that only considered the daily driving distance is calculated.
Technical Paper

Potential Risk Assessment Algorithm in Car Following

2019-04-02
2019-01-1024
In this paper, a potential risk assessment algorithm is proposed. The obvious risk assessment measure is defined as time to collision (TTC), whereas the potential risk measure is defined as the time before the host vehicle has to decelerate to avoid a rear-end collision assuming that the target vehicle brakes, i.e. time margin (TM). The driving behavior of the human driver in the dangerous car following scenario is studied by using the naturalistic driving data collected by video drive record (VDR), which include 78 real dangerous car following dangerous scenarios. A potential risk assessment algorithm was constructed using TM and the dangerous car following scenarios. Firstly, the braking starting time during dangerous car following is identified. Next, the TM at brake starting time of the 78 dangerous car following scenarios is analyzed. In the last, the thresholds of the potential risk levels are achieved.
X