Search Results

The newly proposed Euro 7 emission standards have added regulations limiting ammonia emissions for gasoline vehicles. This paper proposes a new emissions-control strategy to satisfy the regulated ammonia emission levels, using deceleration cylinder cut-off (DCCO) to reduce or eliminate conventional deceleration fuel cutoff (DFCO) and the associated lean-rich excursions in the three-way catalyst during oxygen saturation and desaturation. The improved air-fuel ratio management closer to stoichiometry lowers the ratio of CO to NOx and thus the ammonia (NH3) formation rate inside catalytic converter. Tests show more than 80% reduction of ammonia emission on the WLTC drive cycle without increasing other regulated emissions.

Multi-level Miller-cycle Dynamic Skip Fire (mDSF) is a combustion engine technology that improves fuel efficiency by deciding on each cylinder-event whether to skip (deactivate) the cylinder, fire with low (Miller) charge, or fire with a high (Power) charge. In an engine with two intake and two exhaust valves per cylinder, skipping can be accomplished by deactivating all valves, while firing with a reduced charge is accomplished by deactivating one of the intake valves. This new ability to modulate the charge level introduces new failure modes. The first is a failure to reactivate the single, high-charge intake valve, which results in a desired High Fire having the air intake of a Low Fire. The second is a failure to deactivate the single intake valve, which results in a Low Fire having the air intake of a High Fire.

Cylinder deactivation is a fuel consumption and CO2 reduction technology for internal combustion engines that deactivates cylinders at light to moderate loads, allowing the remaining firing cylinders to operate near optimum efficiency. Dynamic Skip Fire (DSF) uses full-authority cylinder deactivation that allows any cylinder of the engine to be deactivated in sequence. In previous SAE papers, both DSF technology and the synergies between DSF and electrification (eDSF) have been described. Recent engine technology includes deactivation mechanisms that do not effectively incorporate individual cylinder control. Nevertheless, it is still quite possible to improve the efficiency of engines equipped with these ganged-deactivation mechanisms. By grouping all cylinders into a deactivation mode, no air is pumped through the cylinders as it would be during the corresponding conventional operation that deactivates fuel alone.

Super ultra-low NOX emission engine concepts are essential to comply with future emission legislations. To meet the future emission standards, application of advanced diesel exhaust aftertreatment systems (EATS), such as Diesel Oxidation Catalyst (DOC), Lean NOX Trap (LNT), Selective Catalytic Reduction coatings on Soot Filters (SCRF) and underfloor SCR, is required. Effective customized thermal management strategies are essential to ensure fast light-off of the EATS after engine cold start, and to avoid significant cooldown during part load operation. The authors describes the investigation of different exhaust gas heating measures, such as intake throttling, late fuel injection, exhaust throttling, advanced exhaust cam phasing, retarded intake cam phasing, cylinder deactivation, full turbine bypass, electric catalyst heating and electrically heated intake manifold strategies.

Advanced powertrains for modern vehicles require the optimization of conventional combustion engines in combination with tailored electrification and vehicle connectivity strategies. The resulting systems and their control devices feature many degrees of freedom with a large number of available adjustment parameters. This obviously presents major challenges to the development of the corresponding powertrain control logics. Hence, the identification of an optimal system calibration is a non-trivial task. To address this situation, physics-based control approaches are evolving and successively replacing conventional map-based control strategies in order to handle more complex powertrain topologies. Physics-based control approaches enable a significant reduction in calibration effort, and also improve the control robustness.

Amid various cylinder deactivation technologies in automobile engines which provide better fuel efficiency, Dynamic Skip Fire (DSF) has proved to be promising. In DSF, a firing decision is made before every cylinder firing opportunity based on the engine torque requested. Providing this technology to automakers in form of a software object integratable with the customer’s engine controller is done by careful specification of interfaces and execution context definitions. The timing and performance of the software objects integrated with controller firmware can be dependent on the platform and compiler development environment used by the customer. This paper discusses the development of a code test environment for producing high-confidence verification. To do so an industry-accepted verification tool suite is used. Execution timing data of various functions of the source code is analyzed in detail, as well as input-output correctness.

The Bharat Stage (CEV/Tractor) IV & V emission legislations will come into force in Oct 2020 & Apr 2024 respectively, posing a major engineering challenge in terms of system complexity, reliability, costs and development time. Solutions for the EU Stage-V NRMM legislation in Europe, from which the BS-V limits are derived, have been developed and are ready for implementation. To a certain extent these European solutions can be transferred to the Indian market. However, certain market-specific challenges are yet to be defined and addressed. In addition, a challenging timeline has to be considered for application of advanced technologies and processes during the product development. In this presentation, the emission roadmap will be introduced in the beginning, followed by a discussion of potential technology solutions on the engine itself as well as on the after treatment components.

Upcoming China 4th stage of fuel consumption regulation and China 6a emission legislation require improvement of many existing engines. This paper summarizes an upgrade of combustion system and mechanical layout for a four-cylinder engine family. Based on an existing production process for a naturally aspirated 2.0-liter gasoline engine, a 1.8-liter down-speeded and turbocharged gasoline engine is derived. Starting development by analysis of engine base geometry, a layout for a Miller-Cycle gas exchange with early closing of intake valves is chosen. Requirements on turbocharger configuration are investigated with one-dimensional gas exchange simulation and combustion process will be analyzed by means of 3D-CFD simulation. Challenging boundary conditions of a very moderate long-stroke layout with a stroke/bore-ratio of only 1.037 in combination with a cost efficient port fuel injection system and fixed valve lift profiles are considered.

Dynamic skip fire (DSF) has shown significant fuel economy improvements via reduction of pumping losses that generally affect throttled spark-ignition engines. For production readiness, DSF engines must meet regulations for on-board diagnostics (OBD-II), which require detection and monitoring of misfire in all passenger vehicles powered by an internal combustion engine. Numerous misfire detection methods found in the literature, such as those using peak crankshaft angular acceleration, are generally not suitable for DSF engines due to added complexity of skipping cylinders. Specifically, crankshaft acceleration traces may change abruptly as the firing sequence changes. This article presents a novel method for misfire detection in a DSF engine using machine learning and artificial neural networks. Two machine learning approaches are presented.

Cylinder deactivation in multicylinder spark-ignition (SI) engines leads to increased fuel efficiency at part load by allowing fired cylinders to operate closer to their peak thermal efficiency compared to all-cylinder operation. Unlike traditional cylinder deactivation strategies that are limited to deactivating only certain cylinders, Dynamic Skip Fire (DSF) is an advanced cylinder deactivation control strategy that makes deactivation decisions for every cylinder on an individual firing opportunity basis to best meet driver torque demand while saving fuel and mitigating noise, vibration, and harshness (NVH). During DSF operation, inducted charge air mass can vary for each firing event due to the firing sequence history. To maximize efficiency, cylinder fueling should be adjusted for each firing event in DSF based on the inducted charge air mass for that event.

Tula’s Dynamic Skip Fire (DSF®) technology combines highly responsive torque control with cylinder deactivation to optimize fuel consumption of spark ignited engines. Through careful control of individual combustion events, engine operation occurs at peak efficiency over the full range of torque demand. A challenge with skip-fire operation is avoiding objectionable noise and vibration. Tula’s DSF technology uses sophisticated firing control algorithms which manage the skip-fire sequence to avoid excitation of the powertrain and vehicle at sensitive frequencies. DSF enables a production-quality driving experience while reducing CO2 emissions by 8-15% with no impact on regulated toxic emissions. Moreover, DSF presents a high value solution for meeting global emissions mandates, with estimated cost less than $40 per percent gain in fuel efficiency.

In-use compliance under LEV III emission standards, GHG, and fuel economy targets beyond 2025 poses a great opportunity for all ICE-based propulsion systems, especially for light-duty diesel powertrain and aftertreatment enhancement. Though diesel powertrains feature excellent fuel-efficiency, robust and complete emissions controls covering any possible operational profiles and duty cycles has always been a challenge. Significant dependency on aftertreatment calibration and configuration has become a norm. With the onset of hybridization and downsizing, small steps of improvement in system stability have shown a promising avenue for enhancing fuel economy while continuously improving emissions robustness. In this paper, a study of current key technologies and associated emissions robustness will be discussed followed by engine and aftertreatment performance target derivations for LEV III compliant powertrains.

Dynamic skip fire (DSF) has shown significant fuel economy improvement potential via reduction of pumping losses that generally affect throttled spark-ignition (SI) engines. In DSF operation, individual cylinders are fired on-demand near peak efficiency to satisfy driver torque demand. For vehicles with a downsized-boosted 4-cylinder engine, DSF can reduce fuel consumption by 8% in the WLTC (Class 3) drive cycle. The relatively low cost of cylinder deactivation hardware further improves the production value of DSF. Lean burn strategies in gasoline engines have also demonstrated significant fuel efficiency gains resulting from reduced pumping losses and improved thermodynamic characteristics, such as higher specific heat ratio and lower heat losses. Fuel-air mixture stratification is generally required to achieve stable combustion at low loads.

In view of changing climatic conditions all over the world, Green House Gas (GHG) saving related initiatives such as reducing the CO2 emissions from the mobility and transportation sectors have gained in importance. Therefore, with respect to the large U.S. market, the corresponding legal authorities have defined aggressive and challenging targets for the upcoming time frame. Due to several aspects and conditions, like hesitantly acting clients regarding electrically powered vehicles or low prices for fossil fuels, convincing and attractive products have to be developed to merge legal requirements with market constraints. This is especially valid for the market segment of Light-Duty vehicles, like SUV’S and Pick-Up trucks, which are in high demand.

The emission legislations are becoming increasingly strict all over the world and India too has taken a big leap in this direction by signaling the migration from Bharat Stage 4 (BS 4) to BS 6 in the year 2020. This decision by the Indian government has provided the Indian automotive industry a new challenge to find the most optimal solution for this migration, with the existing BS 4 engines available in their portfolio. Indian market for the LCV segment is highly competitive and cost sensitive where the overall vehicle operation cost (vehicle cost + fluid consumption cost) is the most critical factor. The engine and after-treatment technology for BS 6 emission levels should consider the factors of minimizing the additional hardware cost as well as improving the fuel efficiency. Often both of which are inversely proportional. The presented study involves the optimization of after treatment component size, layout and various systems for NOx and PM reduction.

Despite the trend in increased prosperity, the Indian automotive market, which is traditionally dominated by highly cost-oriented producion, is very sensitive to the price of fuels and vehicles. Due to these very specific market demands, the U-LCV (ultra-light commercial vehicle) segment with single cylinder natural aspirated Diesel engines (typical sub 650 cc displacement) is gaining immense popularity in the recent years. By moving to 2016, with the announcement of leapfrogging directly to Bharat Stage VI (BS VI) emission legislation in India, and in addition to the mandatory application of Diesel particle filters (DPF), there will be a need to implement effective NOx aftertreament systems. Due to the very low power-to-weight ratio of these particular applications, the engine operation takes place under full load conditions in a significant portion of the test cycle.

The Bharat Stage VI (BS-VI) emission legislation will come into force in 2020, posing a major engineering challenge in terms of system complexity, reliability, cost and development time. Solutions for the EURO VI on-road legislation in Europe, from which the BS-VI limits are derived, have been developed and have already been implemented. To a certain level these European solutions can be transferred to the Indian market. However, several market-specific challenges are yet to be defined and addressed. In addition, a very strict timeline has to be considered for application of advanced technologies and processes during the product development. In this paper, the emission roadmap will be introduced in the beginning, followed by a discussion of potential technology solutions on the engine itself as well as on the exhaust aftertreatment side. This includes boosting and fuel injection technologies as well as different exhaust gas recirculation methods.

This work is a continuation of earlier results presented by the authors. In the current investigations the biofuels hydrogenated vegetable oil (HVO) and 1-octanol are investigated as pure components and compared to EN 590 Diesel. In a final step both biofuels are blended together in an appropriate ratio to tailor the fuels properties in order to obtain an optimal fuel for a clean combustion. The results of pure HVO indicate a significant reduction in CO-, HC- and combustion noise emissions at constant NOX levels. With regard to soot emissions, at higher part loads, the aromatic free, paraffinic composition of HVO showed a significant reduction compared to EN 590 petroleum Diesel fuel. But at lower loads the high cetane number leads to shorter ignition delays and therefore, ignition under richer conditions.

In recent years, more attention has been focused on environment pollution and energy source issues. As a result, increasingly stringent fuel consumption and emission legislations have been implemented all over the world. For automakers, enhancing engine’s efficiency as a must contributes to lower vehicle fuel consumption. To reach this goal, Geely auto started the development of a 3-cylinder 1.0L turbocharged direct injection (TGDI) gasoline engine to achieve a challenging fuel economy target while maintaining fun-to-drive and NVH performance. Demanding development targets for performance (specific torque 205Nm/L and specific power 100kW/L) and excellent part-load BSFC were defined, which lead to a major challenge for the design of the combustion system. Considering air/fuel mixture, fuel wall impingement and even future potential for lean burn combustion, a symmetrical layout and a central position for the injector with 200bar injection pressure was determined.

Reducing fuel consumption is a major challenge for vehicle, especially for SUV. Cooling loss is about 30% in total energy loss under NEDC (New European Driving Cycle) cycle. It is necessary to optimize vehicle thermal management system to improve fuel economy. Otherwise, rapid warm-up is beneficial for friction reduction and passenger comfort in cold-start. Vehicle thermal behavior is influenced by cooling system layout, new technology and control strategy. Thermal management simulation is effective to show the energy flow and fuel consumption under the influence of new technology under NEDC cycle. So 1D thermal management simulation model is created, including vehicle, cooling system, lubrication system and detailed engine model with all friction components. And the interrelations between all the components are considered in the model. For model calibration, large amount of data is obtained from vehicle tests such as transient fuel consumption and transient coolant temperature.