Search Results

Disc brake squeal is always a challenging multidisciplinary problem in vehicle noise, vibration, and harshness (NVH) that has been extensively researched. Theoretical analysis has been done to understand the mechanism of disc brake squeal due to small disturbances. Most studies have used linear modal approaches for the harmonic vibration of large models. However, time-domain approaches have been limited, as they are restricted to specific friction models and vibration patterns and are computationally expensive. This research aims to use a time-domain approach to improve the modeling of brake squeal, as it is a dynamic instability issue with a time-dependent friction force. The time-domain approach has been successfully demonstrated through examples and data.

In recent years there has been an increase in the development of vehicles that use alternative energy sources, more specifically electric vehicles, intending to establish the transition from combustion engines, bringing to the automotive chain a reduction in the consumption of fossil fuels. Electrified vehicles help to improve air quality by drastically reducing the emission of harmful gases and contributing to a considerable improvement in sound quality, due to the use of their silent electric motors. A material allied to these alternative technologies is graphene, few layers (usually up to 6) of Carbon atoms arranged in a hexagonal and crystalline form in a two-dimensional plane lattice. Its unique chemical structure allows it to share its exceptional properties with other materials, making it a strong candidate to meet the needs and improve products of the automotive sector.

During the design conception of an automobile, typically low-fidelity physics-based simulations are coupled with engineering judgement to define key architectural components and subsystems which limits the capability to identify NVH issues arising from systems interaction. This translates to non-optimal designs because of unexplored design opportunities and therefore, lost business efficiencies. The sparse design information available during the design conception phase limits the development of representative higher fidelity physics-based simulations. To address that restriction on design optimization opportunities, this paper introduces an alternate approach to develop reduced order predictive models using regression techniques by harnessing historical measurement and simulation data. The concept is illustrated using two driveline NVH phenomenon: axle whine and take-off shudder.

Noise and vibration evaluation of driveline clunk can be challenging as it is the result of driver input conditions and is transient in nature. As with many noise and vibration challenges, the use of computer-aided engineering (CAE) simulation is useful as it allows for detailed study of the phenomenon and prediction of potential improvements. A hybrid approach of physical test-based measurements and CAE analysis can be used to leverage the advantages of CAE in a comprehensive evaluation including the total vehicle noise, vibration, and harshness (NVH) performance. In this paper we present work performed to facilitate engineering evaluations of driveline clunk using both measured test and CAE simulation data. We explain how we used measured test data to inform the CAE analysis, how the simulation approached modelling of the transient clunk event, and how the measured data was used to provide contextual sound for realistic evaluation of the CAE output as heard by the passengers.

The ported shroud casing treatment for turbocharger compressors offers a wider operating flow range, elevated boost pressures at low compressor mass flow rates, and reduced broadband whoosh noise in spark-ignition internal combustion engine applications. However, the casing treatment elevates tonal noise at the blade-pass frequency (BPF). Typical rotational speeds of compressors employed in practice push BPF noise to high frequencies, which then promote multi-dimensional acoustic wave propagation within the compressor ducting. As a result, in-duct acoustic measurements become sensitive to the angular location of pressure transducers on the duct wall. The present work utilizes a steady-flow turbocharger gas stand featuring a unique rotating compressor inlet duct to quantify the variation of noise measured around the duct at different angular positions.

Exhaust sensors and actuators used in automotive applications are subjected to wide variety of operating ambient conditions , the performance of these actuators is challenging especially at cold ambient operating conditions, active exhaust tuning valves with position sensors are used to adjust the sound levels, or noise, vibration and harshness (NVH) from a control unit within the vehicle that leads to an improved driving experience wherein the driver selects their preferred sound levels. However, the operating behavior is crucially influenced by the characteristics of the drive cycle and ambient temperature. The study in this paper is intended to evaluate the icing formation at the start of drive cycle and at different ambient temperature conditions. The test data were obtained through real road and chassis dyno testing at different ambient conditions.

The work presented here is part of the research done in the field of voice biometrics. This paper helps to understand the state-of-the-art in speaker recognition technology potentially capable of solving challenges related to speaker identification (to identify a speaker among multiple speakers) and speaker verification/authentication (to recognize the current speaking person at a pre-defined access level and authenticate accordingly). The research was focused on performing an unbiased evaluation of two individual voice biometric services. The level of accuracy in identifying and authenticating individuals using these services provides an insight into the current state of technology and the state of what other dual authentication methods could be used to achieve a desired True Acceptance Rate (TAR) and False Acceptance Rates (FAR).

Sunroof is placed in certain high-end vehicles to give user a better driving experience. All automakers are searching alternatives to reduce weight and cost in the vehicle, in which sunroofs are also impacted. Some alternatives are already applied, as a honeycomb paper used in some sunshades that presents benefits, as less weight and with a good cost reduction. Although, due the reduced weight for this part produced in this material, it shows more susceptibility to reproduce the vibration that vehicle propagates in movement, especially in bad condition roads. The sunroof assembly is dependent of the roof reinforcement and roof skin, but in this special case, the validation could be done in the components itself because the interaction of the sunshades is directly dependent of the other sunroof parts, as rails and front frame.

Squeak and rattle are two undesirable occurrences during component operation and during vehicle driving condition, resulting in one of the top complains from costumers. One common grievance could happen during the user exterior handle operation and during side door closing. The exterior handle system during the operation could generate a squeak between interface parts, if materials and geometric tolerances was not been carefully designed. Also, vibration generated during door closing effort, might generate squeak between parts since the reinforcement for exterior handle touches the outer sheet metal internally. For this reason several guidelines might be included to avoid potential noise condition for this system during vehicle lifetime as correct material reduce friction between parts, taking into consideration the geometric condition between parts. Plus, coupling system on handles two pieces should also be evaluated to avoid squeak during use.

The recent automotive industry trend towards electrification has created new challenges for NVH engineers. These challenges stem from new powertrain architectures and their complex interactions, the governing control strategies which aim to optimize energy management, and new unmasked sources of excitation. Additionally, vehicle manufacturers are attempting to reduce hardware testing in order to rapidly satisfy increasing production demand and to minimize its costs. Hence, to meet the above-mentioned challenges up front in the development process of Hybrid Electrical Vehicles (HEVs) while balancing competing design objectives of drivability, durability and NVH, a simulation-led design and optimization is required. NVH problems are often the result of mechanisms that originate through complex interactions between different physical domains (flow, electromagnetic, structural/mechanical, control logic, etc.) and the assembly of individual components into a complete system.

Vehicle manufacturers face increasing challenges in auditing the build quality of their vehicles while considering increasing consumer demands regarding NVH performance. This effect is compounded with the rise in electric and hybrid vehicles. The ability to audit vehicles for a variety of noise types is becoming increasingly important; these include powertrain noise, road noise, and wind noise. An automated measurement system was developed with specific algorithms and sound quality metrics to not only audit vehicle production quality but to add objective data, pass-fail criteria, and trend analysis.

The Single Sequential Turbocharger (SST) used in Ford’s 6.7L Scorpion Diesel is analyzed using Computational Fluid Dynamics (CFD) to draw conclusions about the compressor stability at low mass flows. The SST compressor concept consists of a double-sided wheel which flows in parallel fed by two separate inlets (front and rear), followed by a single vane-less diffuser, and a volute. CFD simulations for the full stage are performed at low mass flow rates Both, front and rear, sides have ported shroud casing-treatment (CT) in the inlet region. An objective of the analysis is to determine which side of the SST unit compressor (front or rear on the double-sided wheel) suffers flow break down first as the mass flow is reduced, and its impact on the overall stability of the SST compressor. Another objective is to better understand the interactions between the compressor inlet flow and the flow through the casing-treatment.

It is a common practice to conduct NVH fingerprinting and benchmarking assessments at the powertrain level, to understand source level noise and vibration. To assess the NVH influence of engine, e-motor, and transmission, sub-system testing is often conducted in addition to full powertrain testing. These powertrain or sub-system investigations provide valuable information regarding the status of “source” level excitations relative to targets and / or competitive powertrains. In the case of transmissions and e-machines, it is particularly important to understand source level tonal content and how this will be perceived at the vehicle level. However, variation in component design results in differences in order content, which complicates the process of objectively comparing multiple products. Multiple methods are presented here for characterizing tonal content of transmission and e-machines, based on assessments conducted in a component hemi-anechoic dynamometer test cell.

The conventional ported shroud recirculation casing treatment elevates narrowband noise at blade pass frequency. A new ported shroud recirculating casing treatment was implemented in Ford’s 3.5L turbo gas engine as Noise Vibration and Harshness (NVH) counter measure to reduce whoosh (broadband flow noise) noise without elevating narrowband noise at blade pass frequency. The new ported shroud design incorporates holes between the main and secondary recirculating passage and a slight cross-sectional area reduction just upstream of the impeller. These design features reduce whoosh noise without elevating the first order and the sixth order tonal noise at blade pass frequency. The new ported shroud design decreases narrowband tonal noise sound pressure level by 3-6 dB in the low to mid flow region compared to the baseline design. Computational Fluid Dynamics (CFD) tools were used to develop this casing treatment design.

Variable Displacement Oil Pump (VDOP) is becoming the design of choice for engine friction reduction and fuel economy improvement. Unfortunately, this pump creates excessive pressure ripples, at the outlet port during oil pump shaft rotation, causing oscillating forces within the lubrication system and leading to the generation of objectionable tonal noises and vibrations. In order to minimize the level of noise, different vanes spacing and porting geometries are used. Moreover, an oil pressure relief groove can be added, at the onset of the high pressure port, to achieve this goal. This paper presents an optimization method to identify the best geometry of the oil pressure relief groove. This method integrates adaptive meshing, 3D CFD simulation, Matlab routine and Genetic Algorithm based optimization. The genetic algorithm is used to create the required design space in order to perform a multi-objective optimization using a large number of parameterized groove geometries.

In the recent years, adjoint optimization has gained popularity in the automotive industry with its growing applications. Since its inclusion in the mainstream commercial CFD solvers and its continuously added capabilities over the years, its productive usage became readily available to many engineers who were previously limited to interfacing the customized adjoint source code with CFD solvers. The purpose of this work is to demonstrate using an adjoint solver a method to optimize duct shape that meets multiple design objectives simultaneously. To overcome one of the biggest challenges in the duct design, i.e. the severe packaging constraints, the method here uses geometrically constrained adjoint to ensure that the optimum shape always fits into the user-defined packaging space. In this work, adjoint solver and surface sensitivity calculations are used to develop the optimization method.

Weight is a major factor during the development of Automotive Powertrains due to stringent fuel economy requirements. Light weighting constitutes a challenge to the engineering community when trying to deliver quieter powertrains. For this reason, the NVH (Noise Vibration Harshness) CAE engineers are adopting advanced vibro-acoustic simulation methods combined with topology optimization methods to drive the design of the under hood components for Noise Vibration and Harshness. Vibro-acoustic computational methods can be complex and require significant computation effort. Computation of Equivalent Radiated Power (referred to as ERP) is a simplified method to assess maximum dynamic radiation of components for specific excitations in frequency response analysis which in turn affects radiated sound. Topology Optimization is a mathematical technique used to find the best material distribution for structural systems in order to deliver a specific objective under clearly defined constraints.

In this paper, a CAE methodology based on a multiphysics approach for engine gear noise evaluation is reviewed. The method comprises the results and outputs from several different analytical domains to perform the noise risk assessment. The assessment includes the source-path analysis of the gear-induced rattling and whining noise. The vibration data from the exterior surface of the engine is extended through acoustic analysis to perform the engine noise simulation and to identify acoustic hot spots contributing to the noise. The study includes simulations under different engine loading conditions with results presented in both time and frequency domains. Various sensitivity analyses involving different gear geometries and micro-geometries are investigated as well. Finally, the simulation results from three different engines are compared vis-a-vis.

The EMI coupling mechanisms of a DC-DC converter in electrified vehicles are investigated for both conducted and radiated EMI. The noise sources and propagation paths are identified and quantified. The results show that the magnetic coupling between noise sources to some sensitive locations, including HV/LV terminals and CAN connector, can cause excessive emissions. The coupling between different components of the EMI filters may also lead to the degradation of the filter performances. Strategies are proposed to reduce the coupling, improve the filter performance and mitigate the emissions. The performances are verified in experiment.

In this paper, an approach to analyze voice recognition data to understand how customers use voice recognition systems is explored. The analysis will help identify ASR failures and usability related issues that customers encounter while using the voice recognition system. This paper also examines the impact of these failures on the individual speech domains (media control, phone, navigation, etc.). Such information can be used to improve the current voice recognition system and direct the design of future systems. Infotainment system logs, audio recordings of the voice interactions, their transcriptions and CAN bus data were identified to be rich sources of data to analyze voice recognition usage. Infotainment logs help understand how the system interpreted or responded to customer commands and at what confidence level.