Search Results

One of the biggest challenges for mobility engineers today is the reduction of fuel consumption while keeping or even improving the automobiles propulsion system performance. A great part of the current powertrain components is developed to work at high engine loads and extreme environmental conditions, among which the engine cooling system, for example. As the overall vehicle efficiency depends directly on the thermal system design, it is important to make a careful investigation of the external ambient to develop this system on the best possible way, seeking to minimize the negative impacts at normal driving situations, which represents the most of the vehicle's life cycle. In this regard, the present paper reports a numerical study about the impacts of different cooling system hardware configurations on the fuel consumption of a turbocharged flex-fuel engine.

The work focuses on studying ethanol spray behavior injected directly inside a spark ignited internal combustion engine in the compression stroke. An experimental procedure for measuring spray penetration and spray overall cone angle produced by a multi-hole direct injector was developed by means of computational codes written in Matlab environment for working with images of spray injections and to acquire calculated results in an automatic way. The shadowgraph technique with back continuous illumination associated with a high speed recording image process was used in a single cylinder optical research engine for acquiring images of Brazilian ethanol fuel injected at 120° before the top dead center of compression stroke. The process of spray injections occurred with engine speeds of 1000 rpm, 2000 rpm and 3000 rpm. The results showed that spray penetrations decrease and spray cone angle increase when the engine speed is raised.

Diesel engines have been used on the aeronautical market for a long time. Despite this fact, there are few studies showing the potential cost savings of using this type of technology. In this way, the goal of this paper is to find out whether or not it is advantageous to use an Otto or Diesel cycle engine on general aviation light aircraft. It is well known that both of them have pros and cons, however, the possibility of using Jet A-1 (kerosene) as fuel gives the Diesel engine a clear advantage in a market like Brazil, where the price of the regular piston fuel (AvGas) keeps rising to astonishing values. Throughout this paper, a detailed study of the fixed and variable costs of two similar aircraft, both Cessnas 172 equipped with Otto and Diesel cycle engines is conducted, comparing fuel consumption, performance levels, and other factors.

Environmental policies and fuel costs have driven the development of new technologies for internal combustion engines. In this sense, the use of mixtures with small portions of fuel allows lower fuel consumption and pollutants emissions, emerging as a promising strategy. Despite the advantages, lean burn requires a larger energy source to provide satisfactory flame propagation speed and consequently a stable combustion. The use of pre-chamber ignition systems (PCIS) has been used in SI engines to assist the start of combustion of lean mixtures, in which a supplementary fuel system can stratify the amount of either liquid or gaseous fuels supplied to the pre-chamber. In this context, this paper aims to evaluate combustion characteristics of a commercial engine with the use of stratified PCIS operating with impoverished mixtures of ethanol-air in main-chamber and hydrogen assistance in pre-chamber.

Extensive studies of pre-chamber ignition systems in internal combustion engines have proven its effectiveness in reduction of fuel consumption and improvement in several combustion parameters. Considering the different types of pre-chamber configurations, this paper aims to compare the combustion in a SI engine with both homogeneous and stratified pre-chamber ignition systems. To achieve this objective a system with the ability to control the hydrogen injection in the pre-chamber was built. This system was installed in a multi-cylinder Ford Sigma 1.6L engine and tested in a dynamometric room. Tests consisted in imposing a constant rotation and IMEP to test three conditions: standard spark ignition, pre-chamber ignition system without fuel injection (homogenous) and with hydrogen injection (stratified). It was possible to identify that with the use of pre-chamber ignition system there is a reduction in specific fuel consumption and in the combustion duration.

Resistive forces are a great source of fuel consumption in vehicles. In particular, rolling resistance represent the major resistance force at low speeds. It is highly influenced by the inflation pressure of the tire and vertical load over it. In the present work, a computer model is created with the objective of investigating the influence of tire inflation pressure on fuel consumption and rolling resistance force. Pressure is varied and parameters analyzed at different vehicle speeds for two different calculation methods. Results show significant decrease in fuel consumption and rolling resistance force as inflation pressure is augmented.

The growing demand for more efficient and less polluting engines has lead the scientific community to further develop the road map engine technologies, including direct fuel injection. Direct injection research demands the investigation of spray formation and its characteristics. The present work performs the characterization of the macroscopic parameters of ethanol sprays (E100) produced with a fuel gauge pressure of 80 bar and gauge back pressures of 0, 5 and 10 bar. The sprays analysis was performed using high speed filming by means of Shadowgraph technique. Computational routines of matrix analysis were applied to measure the spray cone angles, penetration and penetration rate. The spray visualization demanded an experimental apparatus composed of a pressurized cylinder with nitrogen, a fuel tank as pressure vessel, an injection driver equipped with a peak and hold module controlled by a MoteC M84, a Phantom V7.3 high speed camera and LEDs for illumination.

Global trends in the development of spark ignition internal combustion engines lead to the adoption of solutions that reduce CO2 emissions and fuel consumption. Downsizing is a well-established path for this reduction, but it is necessary to use other technologies in order to achieve these ever more rigorous levels. A homogeneous torch ignition system is a viable alternative for reducing CO2 emissions with a combined reduction in specific fuel consumption and increased thermal efficiency. Thus a prototype adapted from an Otto engine with four cylinders is used for analysis. The performance and CO2 emission reference data were initially obtained with the baseline engine operating with a stoichiometric mixture. Then for the same conditions of BMEP, angular velocity and gradual lean of the mixture from the stoichiometry, the results of the adapted system are obtained.

Environmental issues and energy security are critical concerns of the most countries. According researchers, excessive growth of land vehicles is one of the biggest contributors to global air pollution and oil reserves reduction. In this context, the use of lean burn technologies emerges as a promising strategy, allowing lower fuel consumption and pollutants emissions. Present work aims to analyze the behavior of a current commercial engine, gasoline fueled, varying the air-fuel ratio without the use of lean burn ignitions technologies. Analysis was performed through bench dynamometer tests, evaluating cylinder pressure, exhaust gas temperature, fuel conversion efficiency, cycle thermal efficiency, coefficient of variation in indicated mean effective pressure, apparent heat release rate, flame development angle and burn duration.

The trends in the development of spark ignition engines leads to the adoption of lean mixtures in the combustion chamber. Torch ignition systems have potential to reduce simultaneously the NOx and CO emissions, while keeping the fuel conversion efficiency at a high level. This study aims to design and analyze a torch ignition system running with ethanol on lean homogeneous charge, adapted to an Otto cycle single-cylinder engine with optical visualization. The main objective is to achieve combustion stability under lean burn operation and to expand the flammability limit for increasing engine efficiency by means of redesigning the ignition system adapting a pre-chamber to the main combustion chamber. Experiments were conducted at constant speed (1000 rpm) using ethanol (E100) as fuel, for a wide range of injection, ignition and mixture formation parameters. Specific fuel consumption and combustion stability were evaluated at each excess air ratio.

A multi-hole direct injection injector was studied by means of image analysis. Methodologies based on an automatic process of cone angle measurement and edge detection were applied for the spray images generated by a 100 bar injection pressure discharged into a pressurized rigid chamber. A criterion based on pixel values was taken to localize the spray edges as angular coordinates and also with x and y position data. The high pixel values were associated with liquid phase while the low pixel values were associated to its absence. Computational codes written in MATLAB environment were used to analyze the numerical matrices associated to the images. Using the written MATLAB codes, a comparison of the effect of atmospheric back pressure, inside the chamber, on the spray pattern, cone angle and spray penetration were evaluated. The chamber was pressurized with 2.5, 5.0, 7.5 and 10 bar of back pressure. The tested fluid injected was EXXSOL D60 for simulating ethanol fuel behavior.

The Stratified Torch Ignition (STI) engine is capable of operating with lean mixture and low cyclic variability. These characteristic significantly decreases fuel consumption and emission levels. In the STI engine the combustion starts at a pre-combustion chamber where a stoichiometric mixture is ignited by an electrical spark. Pressure increase in the pre-combustion chamber push the combustion jet flames through a calibrated nozzle to be precisely targeted into the main chamber. These combustion jet flames endowed with high thermal and kinetic energy assures a fast and stable combustion of a lean mixture formed at the main chamber. A STI prototype were built and tested. The main combustion parameters were obtained from the in-cylinder pressure measured during the experiments. A combustion analysis is carried out to explain the significant improvement of the STI engine in regard to the baseline engine which was used as workhorse for the prototype engine construction.

Global climate change and an increasing energy demand are driving the scientific community to further advance internal combustion engine technology. Invented by Sr. Henry Ricardo in 1918 the torch ignition system was able to significantly decrease engine’s fuel consumption and emission levels. Since the late 70s, soon after the Compound Vortex Controlled Combustion (CVCC) created by Honda, the torch ignition system R&D almost ceased due to the issues encountered by very complex and costly mechanic control systems that time. This work presents a stratified torch ignition prototype endowed with a sophisticated electronic control systems and components such as electro-injectors from direct injection systems placed on the pre-combustion chamber. The torch ignition prototype was tested and its performance are presented and compared with the baseline engine, which was used as a workhorse for the prototype engine construction.

Reducing environmental pollution by the transport sector has been influenced according to the increasingly restrictions imposed by regulatory standards. For this, legislation such as Euro (at global level) and Proconve (at local level) set new limits each new phase, usually stipulating reductions in the levels of greenhouse gas emissions. Compliance with these requirements is seen with the vehicle or engine ratings working through the conditions imposed by a standard test cycle. However, standard driving conditions often do not represent the real-world driving conditions, being influenced by relief, traffic lights and other peculiarities of each city or route. This paper aims to compare real-world driving cycles of urban bus and passenger car in the city of Santa Maria, in southern Brazil, with the conditions used for light gasoline vehicles and heavy diesel vehicles approval.

A burning process in a combustion chamber of an internal combustion engine is very important to know the maximum temperature of the gases, the speed of combustion, the ignition delay time of fuel and air mixture exact moment at which ignition will occur. The automobilist industry has invested considerable amounts of resources in numerical modeling and simulations in order to obtain relevant information about the processes in the combustion chamber and then extract the maximum engine performance control the emission of pollutants and formulate new fuels. This study aimed to general construction and instrumentation of a shock tube for measuring shock wave. As specific objective was determined reaction rate and ignition delay time of diesel, biodiesel and ethanol doped with different levels of additive enhancer cetane number. The results are compared with the ignition delay times measured for other authors.

The internal combustion engines require an efficient cooling system, the high temperatures generates at the time of combustion, reaching 2500 K peak burned gas. The materials used in the construction of the cylinder must operate within a maximum value, as well as the fluid film of lubricant oil. A bad dimensioned cooling system can lead to serious consequences such as loss of engine performance and/or efficiency, pre-ignition and increased exhaust emissions and may even lead to the destruction of the engine. In the torch ignition system overheating of the pre-chamber is even more critical and may lead to significant losses. Thus the torch ignition system requires an efficient cooling to prevent deterioration of the pre-chamber and consequently the engine caused by overheating. The solution proposed to resolve this inconvenience is the use of the cooling gallery in the cylinder head, for cooling the pre-chamber that is selected.

The aim of this work is to present the preliminary performance studies of the unmanned, lightweight (less than 10 kg), supersonic research aircraft. The studies comprise the typical mission for the aircraft's first supersonic version, based on the aerodynamic, thrust, and mass characteristics presented in a previous work. The aircraft, named as “Pohox”, is an Unmanned Air Vehicle, or “UAV”, and is intended to be the flying test bed for a multi cycle engine capable to provide thrust in subsonic, transonic and supersonic regimes. Different tools have been developed to perform the analysis. In the analysis, different flight paths are considered in order to provide insights in terms of fuel consumption, altitude and speed gain. Aircraft ‘excess power’ diagrams have been generated, to provide guidance for the definition of the flight paths to be analyzed. Drag dependency with Mach number is considered in the analysis.

A burning process in a combustion chamber of an internal combustion engine is very important to know the maximum temperature of the gases, the speed of combustion, and the ignition delay time of fuel and air mixture exact moment at which ignition will occur. The automobilist industry has invested considerable amounts of resources in numerical modeling and simulations in order to obtain relevant information about the processes in the combustion chamber and then extract the maximum engine performance control the emission of pollutants and formulate new fuels. This study aimed to general construction and instrumentation of a shock tube for measuring shock wave. As specific objective was determined reaction rate and ignition delay time of ethanol doped with different levels of additive enhancer cetane number. The results are compared with the delays measured for the ignition diesel and biodiesel.

It developed a design and construction methodology of a stratified charge torch ignition system for an Otto engine aiming fuel consumption and pollutant emission reduction. The torch ignition system is made of a combustion pre-chamber equipped with a direct fuel injector, an air injector and a spark plug. Fuel is directly injected in the pre-chamber aiming the formation of a lightly rich air fuel mixture. The combustion process starts in the pre-chamber and as the pressure rises, combustion jet flames are produced through interconnection nozzles into the main chamber. The high thermal energy of the jet flames reduces the combustion time, increases the combustion efficiency and allows the engine to efficiently burn lean air fuel mixture of several kinds of fuel in the main chamber, even those that are difficult to ignite. After the combustion takes place in the pre-chamber, air is also injected to help the exhaust process of the combustion products of the previous cycle.

This work shows procedures for analyzing sprays produced by a direct injection injector. The parameters studied were tip penetration, spray pattern, cone angles and velocity profiles. Two different experimental procedures were applied. The first one to get knowledge of the initial stage of injection consisted in recording images in 4000 Hz. With the data obtained, the penetrations and penetration rates were evaluated. The second experimental procedure consisted of using the Particle Image Velocimetry technique to get images and velocity data for getting knowledge of spray pattern, external and internal cone angle and velocity profiles of the spray fully developed. Gasoline and ethanol were the two fluids tested on the experiments. The results showed larger cone angles for gasoline, linear decreasing behavior for velocities on the linear velocity profiles and a transient stage for the magnitude of the velocities in the initial stage of injection.