Search Results

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it has been reported that the 3D printed parts exhibit anisotropic behaviors in microstructure and mechanical properties, that is, depending on the positions (infill orientations) that the parts are placed on a printer platform, the properties of resultant parts can vary greatly. So far, studies on anisotropic behaviors of 3D printed parts have been mostly limited to the static properties (modulus of elasticity, failure strength, etc.); there is a lack on the understanding of mechanical responses of 3D printed parts under dynamic conditions. In the present study, the anisotropic behaviors of 3D printed parts are investigated from the dynamic aspect.

Helmholtz resonators are often used in the design of vehicle mufflers to target tonal noise at a few specific low frequencies generated by the engine. Due to the uncertainty of temperature variations and different engine speeds, multiple resonators may have to be built in series to cover a narrow band of frequencies. Double-tuned Helmholtz resonators (DTHR) normally consist of two chambers connected in series. Openings or necks are created by punching small slots into a thin-walled tube which provide a natural neck passage to the enclosing volume of the Helmholtz resonator. In this paper, numerical analyses using both the boundary element (BEM) and the finite element (FEM) methods are performed and simulation results are compared against one another. A typical real-world muffler configuration commonly used in passenger vehicles is used in a case study.

The two-load method is used to measure the transmission loss of thin panels in two different sized impedance tubes (3.49 cm and 10.16 cm). Samples were initially tested with a clamped boundary condition. This was followed by tests with an elastomer inserted between the tube and tested sample to adjust the boundary condition at the periphery. In all tests performed, the influence of the sample holding method could not be removed from the test. The measured transmission loss was compared to finite element simulation with good agreement for both impedance tubes. Additionally, the effect of a compliant boundary condition along the periphery of the sample was also validated via simulation.

Intake, exhaust, and heating / air conditioning systems in automobiles consist of various common duct elements. Noise arises primarily due to the source and is attenuated using common elements like expansion chambers and resonators. This attenuation is straightforward to predict using plane wave simulation and more advanced numerical methods. However, flow noise is often an unexpected important noise source. Predictions require computer intensive analyses. To better understand the aeroacoustic sources in duct systems, a flow rig has been developed at the University of Kentucky. The flow rig consists of a blower, a silencer to attenuate blower noise, external noise sources, and then the test duct. The flow rig can be equipped with an anechoic termination to measure transmission loss or may be used to measure insertion loss directly. In the latter case, the sound power is measured from the pipe outlet inside of a hemi-anechoic chamber.

Traditional manufacturing processes such as injection or compression molding are often enclosed and pressurized systems that produce homogenous products. In contrast, 3D printing is exposed to the environment at ambient (or reduced) temperature and atmospheric pressure. Furthermore, the printing process itself is mostly “layered manufacturing”, i.e., it forms a three-dimensional part by laying down successive layers of materials. Those characteristics inevitably lead to an inconsistent microstructure of 3D printed products and thus cause anisotropic mechanical properties. In this paper, the anisotropic behaviors of 3D printed parts were investigated by using both laboratory coupon specimens (bending specimens) and complex engineering structures (A-pillar). Results show that the orientation of the infills of 3D printed parts can significantly influence their mechanical properties.

Transfer path analysis is commonly used to determine input forces indirectly utilizing measured responses and transfer functions. Though it is recommended that the source should be detached from the vibrating structure when measuring transfer functions, engineers and technicians frequently have a difficult time in doing so in practice. Recently, a substitute for inverse force determination via transfer path analysis has been suggested. The indirectly determined forces are termed blocked forces and are usable so long as the source and machine are not detached from one another. Blocked forces have the added advantage of being valid even if the machine structure is modified. In this research, a typical automotive engine cover is considered as a receiver structure and is bolted to a plastic source plate excited by an electromagnetic shaker.

Helmholtz resonators are normally an afterthought in the design of mufflers to target a very specific low frequency, usually the fundamental firing frequency of the engine. Due to space limitations in a complex muffler design, a resonator may have to be built by punching a few small holes on a thin-walled tube to create a neck passage into a small, enclosed volume outside the tube. The short neck passage created by punching a few small holes on a thin-walled tube can pose a great challenge in numerical modeling, especially when the boundary element method (BEM) is used. In this paper, a few different BEM modeling approaches are compared to one another and to the finite element method (FEM). These include the multi-domain BEM implemented in a substructure BEM framework, modeling both sides of the thin-walled tube and the details of each small hole using the Helmholtz integral equation and the hypersingular integral equation, and modeling just the mid surface of the thin-walled tube.

Additive manufacturing is slowly changing how components are developed and manufactured. As the technology develops over time, it is anticipated that industry will 3D print sound absorbers in production. Configurations may be considered that would be difficult to manufacture in another way. For exploratory purposes, several designs were 3D printed and positioned in an impedance tube for testing. Though the absorbers developed are based on well-established strategies, the absorbers considered are either difficult to manufacture by another means or take advantage of the unique features of 3D printed parts. The samples measured include long perforations, lightweight panels, and Helmholtz resonators with spiral wound necks. Selected results are compared with acoustic finite element analysis.

The insertion loss of louvered terminations positioned at the end of a rectangular duct is determined using acoustic finite element analysis. Insertion loss was determined by taking the difference between the sound power with and without the louvers at the termination. Analyses were conducted in the plane wave regime and the acoustic source was anechoic eliminating any reflections from the source. The effect of different louver configurations on insertion loss was examined. Parameters investigated included louver length, angle, and spacing between louvers. Based on the analyses, equations were developed for the insertion loss of unlined louvers.

In many industries, muffler and silencer design is primarily accomplished via trial and error. Prototypes are developed and tested, or numerical simulation (finite or boundary element analysis) is used to assess the performance. While these approaches reliably determine the transmission loss, designers often do not understand why their changes improve or degrade the muffler performance. Analyses are time consuming and models cannot be changed without some effort. The intent of the current work is to demonstrate how plane wave muffler models can be used in industry. It is first demonstrated that plane wave models can reliably determine the transmission loss for complicated mufflers below the cutoff frequency. Some tips for developing dependable plane wave models are summarized. Moreover, it is shown that plane wave models used correctly help designers develop intuition and a better understanding of the effect of their design changes.

Partial enclosures are commonly utilized to reduce the radiated noise from equipment. Often, enclosure openings are fitted with silencers or louvers to further reduce the noise emitted. In the past, the boundary element method (BEM) has been applied to predict the insertion loss of the airborne path with good agreement with measurement. However, an alteration at the opening requires a new model and additional computational time. In this paper, a transfer function method is proposed to reduce the time required to assess the effect of modifications to an enclosure. The proposed method requires that the impedance at openings be known. Additionally, transfer functions relating the sound pressure at one opening to the volume velocity at other openings must be measured or determined using simulation. It is assumed that openings are much smaller than an acoustic wavelength. The sound power from each opening is determined from the specific acoustic impedance and sound pressure at the opening.

Carbon nanomaterials such as vertically aligned carbon nanotubes arrays are emerging new materials that have demonstrated superior mechanical, thermal, and electrical properties. The carbon nanomaterials have the huge potential for a wide range of vehicular applications, including lightweight and multifunctional composites, high-efficiency batteries and ultracapacitors, durable thermal coatings, etc. In order to design the carbon nanomaterials for various applications, it is very important to develop effective computational methods to model such materials and structures. The present work presents a structural mechanics approach to effectively model the mechanical behavior of vertically aligned carbon nanotube arrays. The carbon nanotube may be viewed as a geometrical space frame structure with primary bonds between any two neighboring atoms and thus can be modeled using three-dimensional beam elements.

Partial enclosures are a very common way to reduce noise emissions from machinery. However, partial enclosures exhibit complex acoustic behavior that is difficult to predict. The boundary element method (BEM) was used to model the airborne path of a partial enclosure. Simulation results were compared to measurement with good agreement. Special attention is given to the determination of negative insertion loss. It is demonstrated that the enclosure insertion loss will be negative at the Helmholtz frequencies for the enclosure.

The principle of vibro-acoustic reciprocity is reviewed and applied to model sound radiation from a shaker excited structure. Transfer functions between sound pressure at a point in the far field and the velocity of a patch were determined reciprocally both for the to-scale structure and also for a half-scale model. A point monopole source was developed and utilized for the reciprocal measurements. In order to reduce the measurement effort, the boundary element method (BEM) was used to determine the reciprocal transfer functions as an alternative to measurement. Acceleration and sound intensity were measured on patches of the vibrating structure. Reciprocally measured or BEM generated transfer functions were then used to predict the sound pressure in the far field from the vibrating structure. The predicted sound pressure compared favorably with that measured.

Properly characterizing input forces is an important part of simulating structure-borne noise problems. The purpose of this work was to apply a known force reconstruction technique to an earthmoving machinery cab to obtain input functions for modeling purposes. The technique was performed on a cab under controlled laboratory conditions to gain confidence in the method prior to use on actual machines. Forces were measured directly using force transducers and compared to results from the force reconstruction technique. The measured forces and vibrations were used as input power to an SEA model with favorable results.

The paper presents work on development, testing and vehicle integration of inflatable wings for small UAVs. Recent advances in the design of inflatable lifting surfaces have removed previous deterrents to their use and multiple wing designs have been successfully flight tested on UAVs. Primary benefits of inflatable wings include stowability (deploy upon command) and robustness (highly resistant to damage). The inflatable planforms can be either full- or partial-span designs allowing a large design space and mission adaptability. The wings can be stowed when not in use and inflated prior to or during flight. Since inflatable designs have improved survivability over rigid wings, this has the prospect of increasing vehicle robustness and combat survivability. Damage resistance of inflatable wings is shown from results of laboratory and flight tests.

The sound attenuation performance of microperforated panels (MPP) with adjoining air cavity is demonstrated. First of all, simulated results are shown based upon Maa's work investigating the parameters which impact MPP performance [1]. It is shown that the most important parameter is the depth of the adjoining cavity. Following this, an experimental study was undertaken to compare the performance of an MPP to that of standard foam. Following this, two strategies to improve the MPP performance are implemented. These include partitioning the air cavity and having a cavity with varying depth. Both strategies show a marked improvement in MPP attenuation.

Finite element modeling has been used extensively nowadays for predicting the noise and vibration performance of whole engines or subsystems. However, the elastomeric components on the engines or subsystems are often omitted in the FE models due to some known difficulties. One of these is the lack of the material properties at higher frequencies. The elastomer is known to have frequency-dependent viscoelasticity, i.e., the dynamic modulus increases monotonically with frequency and the damping exhibits a peak. These properties can be easily measured using conventional dynamic mechanical experiments but only in the lower range of frequencies. The present paper describes a method for characterizing the viscoelastic properties at higher frequencies using fractional calculus. The viscoelastic constitutive equations based on fractional derivatives are discussed. The method is then used to predict the high frequency properties of an elastomer.

The paper presents work on testing of inflatable wings for unmanned aerial vehicles (UAVs). Inflatable wing history and recent research is discussed. Design and construction of inflatable wings is then covered, along with ground and flight testing. Discussions include predictions and correlations of the forces required to warp (twist) the wings to a particular shape and the aerodynamic forces generated by that shape change. The focus is on characterizing the deformation of the wings and development of a model to accurately predict deformation. Relations between wing stiffness and internal pressure and the impact of external loads are presented. Mechanical manipulation of the wing shape on a test vehicle is shown to be an effective means of roll control. Possible benefits to aerodynamic efficiency are also discussed.

This paper explores the use of inverse boundary element method to identify aeroacoustic noise sources. In the proposed approach, sound pressure at a few locations out of the flow field is measured, followed by the reconstruction of acoustic particle velocity on the surface where the noise is generated. Using this reconstructed acoustic particle velocity, the acoustic response anywhere in the field, including in the flow field, can be predicted. This approach is advantageous since only a small number of measurement points are needed and can be done outside of the flow field, and a relatively fast computational time. As an example, a prediction of vortex shedding noise from a circular cylinder is presented.