Refine Your Search

Topic

Search Results

Technical Paper

Proceedings of Real Driving Emission (RDE) Measurement in China

2018-04-03
2018-01-0653
Light-duty China-6, which is among the most stringent vehicle exhaust emission standards globally, mandates the monitoring and reporting of real driving emissions (RDE) from July, 2023. In the process of regulation promulgation and verification, more than 300 RDE tests have been performed on over 50 China-5 and China-6 certified models. This technical paper endeavors to summarize the experience of RDE practice in China, and discuss the impacts of some boundary conditions (including vehicle dynamic parameters, data processing methods, hybrid propulsion and testing altitude) on the result of RDE measurement. In general, gasoline passenger cars confront few challenges to meet the upcoming RDE NOx requirement, but some China-5 certified samples, even powered by naturally-aspirated engines may have PN issues. PN emissions from some GDI-hybrid powertrain systems also need further reduction to meet China-6 RDE requirements.
Journal Article

Investigation of Combustion and Emission Performance of Hydrogenated Vegetable Oil (HVO) Diesel

2017-10-08
2017-01-2400
Hydrogenated Vegetable Oil (HVO) diesel fuels have the potential to provide a reduced carbon footprint for diesel engines and reduce exhaust emissions. Therefore, it is a strong candidate for transport and diesel powered machines including electricity generators and other off-road machines. In this research, a waste cooking oil derived HVO diesel was investigated for its combustion and emission performance including ignition delays, size segregated particulate number emissions and gaseous emissions. The results were compared to the standard petroleum diesel. A EURO5 emission compliant three litre, direct injection, intercooled IVECO diesel engine equipped with EGR was used which has a maximum power output of 96kW. The engine was equipped with an integrated DOC and DPF aftertreatment system. Both the upstream and downstream of the aftertreatment emissions were measured. The tests were conducted at different RPM and loads at steady state conditions.
Technical Paper

Motion Cueing Evaluation of Off-Road Heavy Vehicle Handling

2016-09-27
2016-01-8041
Motion cueing algorithms can improve the perceived realism of a driving simulator, however, data on the effects on driver performance and simulator sickness remain scarce. Two novel motion cueing algorithms varying in concept and complexity were developed for a limited maneuvering workspace, hexapod/Stuart type motion platform. The RideCue algorithm uses a simple swing motion concept while OverTilt Track algorithm uses optimal pre-positioning to account for maneuver characteristics for coordinating tilt adjustments. An experiment was conducted on the US Army Tank Automotive Research, Development and Engineering Center (TARDEC) Ride Motion Simulator (RMS) platform comparing the two novel motion cueing algorithms to a pre-existing algorithm and a no-motion condition.
Technical Paper

Cold Start SI Passenger Car Emissions from Real World Urban Congested Traffic

2015-04-14
2015-01-1064
The tailpipe exhaust emissions were measured under real world urban driving conditions by using a EURO4 emissions compliant SI car equipped with an on-board heated FTIR for speciated gaseous emission measurements, a differential GPS for travel profiles, thermocouples for temperatures, and a MAX fuel meter for transient fuel consumption. Emissions species were measured at 0.5 Hz. The tests were designed to enable cold start to occur into congested traffic, typical of the situation of people living alongside congested roads into a large city. The cold start was monitored through temperature measurements of the TWC front and rear face temperatures and lubricating oil temperatures. The emissions are presented to the end of the cold start, defined when the downstream TWC face temperature is hotter than the front face which occurred at ∼350-400oC. Journeys at various times of the day were conducted to investigate traffic flow impacts on the cold start.
Technical Paper

Emissions from a HGV Using Used Cooking Oil as a Fuel under Real World Driving Conditions

2015-04-14
2015-01-0905
To maximize CO2 reduction, refined straight used cooking oils were used as a fuel in Heavy Goods Vehicles (HGVs) in this research. The fuel is called C2G Ultra Biofuel (C2G: Convert to Green Ltd) and is a fully renewable fuel made as a diesel replacement from processed used cooking oil, used directly in diesel engines specifically modified for this purpose. This is part of a large demonstration project involving ten 44-tonne trucks using C2G Ultra Biofuel as a fuel to partially replace standard diesel fuels. A dual fuel tank containing both diesel and C2G Ultra Biofuel and an on-board fuel blending system-Bioltec system was installed on each vehicle, which is able to heat the C2G Ultra Biofuel and automatically determine the required blending ratio of diesel and C2G Ultra Biofuel according to fuel temperature and engine load. The engine was started with diesel and then switched to C2G Ultra Biofuel under appropriate conditions.
Journal Article

Speciation of Nitrogen Compounds in the Tailpipe Emissions from a SI Car under Real World Driving Conditions

2014-10-13
2014-01-2812
The tailpipe exhaust emissions were measured using a EURO4 emissions compliant SI car equipped with on-board measurement systems such as a FTIR system for gaseous emission, a differential GPS for velocity, altitude and position, thermal couples for temperatures, and a MAX fuel meter for transient fuel consumption. Various nitrogen species emissions (NO, NO2, NOx, NH3, HCN and N2O) were measured at 0.5 Hz. The tests were designed and employed using two real world driving cycles/routes representing a typical urban road network located in a densely populated area and main crowded road. Journeys at various times of the day were conducted to investigate traffic conditions impacts such as traffic and pedestrian lights, road congestion, grade and turning on emissions, engine thermal efficiency and fuel consumption. The time aligned vehicle moving parameters with Nitrogen pollutant emission data and fuel consumption enabled the micro-analysis of correlations between these parameters.
Technical Paper

Optimisation of Alumina Coated Lightweight Brake Rotor

2014-09-28
2014-01-2501
Aluminium alloys have been used extensively in the automotive industry to reduce the weight of a vehicle and improve fuel consumption which in turn leads to a reduction in engine emissions. The main aim of the current study is to replace the conventional cast iron rotor material with a lightweight alternative such as coated aluminium alloy. The main challenge has been to meet both the cost and functional demands of modern mass-produced automotive braking systems. A sensitivity analysis based on the Taguchi approach was carried out to investigate the effect of various parameters on the thermal performance of a typical candidate disc brake. Wrought aluminium disc brake rotors coated with alumina on the rubbing surfaces were determined to have the best potential for replacing the conventional cast iron rotor at reasonable cost. Optimisation of the structure was subsequently carried out using a genetic algorithm on the selected coated aluminium disc brake rotor.
Journal Article

Determination of Carbon Footprint using LCA Method for Straight Used Cooking Oil as a Fuel in HGVs

2014-04-01
2014-01-1948
In order to improve energy supply diversity and reduce carbon dioxide emissions, sustainable bio-fuels are strongly supported by EU and other governments in the world. While the feedstock of biofuels has caused a debate on the issue of sustainability, the used cooking oil (UCO) has become a preferred feedstock for biodiesel manufacturers. However, intensive energy consumption in the trans-esterification process during the UCO biodiesel production has significantly compromised the carbon reduction potentials and increased the cost of the UCO biodiesel. Moreover, the yield of biodiesel is only ∼90% and the remaining ∼10% feedstock is wasted as by-product glycerol. Direct use of UCO in diesel engines is a way to maximize its carbon saving potentials.
Technical Paper

Real World Diesel Engine Greenhouse Gas Emissions for Diesel Fuel and B100

2013-04-08
2013-01-1514
The transport sector is one of the major contributors to greenhouse gas emissions. This study investigated three greenhouse gases emitted from road transport using a probe vehicle: CO₂, N₂O and CH₄ emissions as a function temperature. It should be highlighted that methane is a greenhouse gas that similarly to carbon dioxide contributes to global warming and climate change. An oxidation catalyst was used to investigate CO₂, N₂O and CH₄ GHG emissions over a real-world driving cycle that included urban congested traffic and extra-urban driving conditions. The results were determined under hot start conditions, but in congested traffic the catalyst cooled below its light-off temperature and this resulted in considerable N₂O emissions as the oxidation catalyst temperature was in the N₂O formation band. This showed higher N₂O during hot start than for diesel fuel and B100 were compared. The B100 fuel was Fatty Acid Methyl Ester (FAME), derived from waste cooking oil, which was mainly RME.
Technical Paper

Examining the Influence of Road Grade on Vehicle Specific Power (VSP) and Carbon Dioxide (CO2) Emission over a Real-World Driving Cycle

2013-04-08
2013-01-1518
The Carbon Dioxide (CO₂) emission from a EURO 3 diesel van over a real-world driving cycle were investigated utilizing part of the Leeds University - Headingly Ring Road (LU-HR) driving cycle, which comprises both an urban (congested) and extra-urban (high speed) driving section. The vehicle used in this research was a 1.8-liter Ford Connect TDCi diesel van. Emissions were monitored by a Portable Emissions Measurement System (PEMS) incorporating an on-board FTIR (Fourier Transform Infrared) exhaust emission measurement system, a Horiba On Board emissions measuring System (OBS 1300) which measured the exhaust flow rate and air/fuel ratio, and a RaceLogic VBOX II differential GPS system provided geographical position, speed and acceleration data. Route topography is known to have substantial influence on vehicle emission.
Technical Paper

Real World Cold Start Emissions from a Diesel Vehicle

2012-04-16
2012-01-1075
This study uses on-board measurement systems to analyze emissions from a diesel engine vehicle during the cold start period. An in-vehicle FTIR (Fourier Transform Inferred) spectrometer and a Horiba on-board measurement system (OBS-1300) were installed on a EURO3 emission-compliant 1.8 TDCi diesel van, in order to measure the emissions. Both regulated and non-regulated emissions were measured, along with an analysis of the NO/NO₂ split. A VBOX GPS system was used to log coordinates and road speed for driving parameters and emission analysis. Thermal couples were installed along the exhaust system to measure the temperatures of exhaust gases during cold start. The real-time fuel consumption was measured. The study also looks at the influence of velocity on emissions of hydrocarbons (HCs) and NOx. The cold start period of an SI-engine-powered vehicle, was typically around 200 seconds in urban driving conditions.
Technical Paper

Analysis of Various Driving Parameters and Emissions for Passenger Cars Driven With and Without Stops at Intersections under Different Test Cycles

2012-04-16
2012-01-0880
Different driving test cycles, the Leeds-West Park (LWP) loop and the Leeds-High Park (LHP) or HPL-A and B (Leeds-Hyde Park Loop-A or B, hereafter referred as HPL-A or B cycle) loop were selected for this urban intersection research and results are presented in this study. Different emissions-compliant petrol passenger cars (EURO 1, 2, 3 and 4) were compared for their real-world emissions. A reasonable distance of steady state speed was needed and for the analysis made in this paper were chosen vehicle speeds at ~20, ~30 and ~40 km/h. Specific spot of periods of driving at the speeds mentioned above were identified, then the starting and ending point was found and the total emissions in g for that period divided by the distance was calculated. A typical urban driving cycle including a loop and a section of straight road was used for the comparison test as it was similar to the legislative ECE15 urban driving cycle.
Technical Paper

Design of a Robust Tyre Force Estimator Using an Extended Kalman Filter

2005-04-11
2005-01-0402
This paper will present a method of estimating tyre friction force using an extended Kalman filter (EKF). A review of current and proposed methods for tyre force estimation from the literature will be given. The EKF developed will estimate vehicle motions and tyre forces as state estimates from a noisy measurement set. The tyre forces will be compared to those from a high order vehicle model with non-linear tyres, which is subjected to the same tests as the measured vehicle, in order to validate the estimated forces. The robustness of the estimator to noise and input errors will be tested. The ultimate aim of this work is to provide estimates of tyre forces to a controller such as ABS or TCS.
Technical Paper

Integration of Active Suspension and Active Driveline to Ensure Stability While Improving Vehicle Dynamics

2005-04-11
2005-01-0414
Most active control systems developed for passenger vehicles are developed as safety systems. These control systems usually focus on improving vehicle stability and safety while ignoring the effects on the vehicle driveability. While stability is the primary concern of these control systems the driveability of the vehicle is also an important consideration. An example of compromised driveability in a stability control system is brake based active yaw control. Brake based systems are very effective at stability control but can have a negative impact on the longitudinal dynamics of a vehicle. The objective of the vehicle control systems developed for the future will be to preserve vehicle driveability while ensuring the stability of the vehicle. In this work, active suspension and active drivelines are developed as stability control systems that have a minimal impact on the driveability of the vehicle.
Technical Paper

Integration of Active Suspension and Active Driveline to Improve Vehicle Dynamics

2004-11-30
2004-01-3544
Many active control systems are developed as safety systems for passenger vehicles. These control systems usually focus on improving vehicle stability and safety while ignoring the effects on the vehicle driveability. In the motorsport environment, increased stability is desirable but not if the driveability of the vehicle is heavily compromised. In this work, active suspension and active drivelines are examined to improve vehicle dynamics and enhance driveability while maintaining stability. The active control systems are developed as separate driveability and stability controls and tested individually then integrated to create a multi-objective control system to improve both driveability and stability. The controllers are tested with standard vehicle manoeuvres.
Technical Paper

The Influence of Simulated Residual and NO Concentrations on Knock Onset for PRFs and Gasolines

2004-10-25
2004-01-2998
Modern engine developments result in very different gas pressure-temperature histories to those in RON/MON determination tests and strain the usefulness of those knock scales and their applicability in SI engine knock and HCCI autoignition onset models. In practice, autoignition times are complex functions of fuel chemistry and burning velocity (which affects pressure-temperature history), residual gas concentration and content of species such as NO. As a result, autoignition expressions prove inadequate for engine conditions straying far from those under which they were derived. The currently reported study was designed to separate some of these effects. Experimental pressure crank-angle histories were derived for an engine operated in skip-fire mode to eliminate residuals. The unburned temperature history was derived for each cycle and was used with a number of autoignition/knock models.
Technical Paper

Integrated Active Steering and Variable Torque Distribution Control for Improving Vehicle Handling and Stability

2004-03-08
2004-01-1071
This paper proposes an advanced control strategy to improve vehicle handling and directional stability by integrating either Active Front Steering (AFS) or Active Rear Steering (ARS) with Variable Torque Distribution (VTD) control. Both AFS and ARS serve as the steerability controller and are designed to achieve the improved yaw rate tracking in low to mid-range lateral acceleration using Sliding Mode Control (SMC); while VTD is used as the stability controller and employs differential driving torque between left and right wheels on the same axle to produce a relatively large stabilizing yaw moment when the vehicle states (sideslip angle and its angular velocity) exceed the reference stable region defined in the phase plane. Based on these stand-alone subsystems, an integrated control scheme which coordinates the control actions of both AFS/ARS and VTD is proposed. The functional difference between AFS and ARS when integrated with VTD is explained physically.
Technical Paper

Drum Brake Contact Analysis and its Influence on Squeal Noise Prediction

2003-10-19
2003-01-3348
A non-linear contact analysis of a leading-trailing shoe drum brake, using the finite element method, is presented. The FE model accurately captures both the static and pseudo-dynamic behaviour at the friction interface. Flexible-to-flexible contact surfaces with elastic friction capabilities are used to determine the pressure distribution. Static contact conditions are established by initially pressing the shoes against the drum. This first load step is followed by a gradual increase of applied rotation to the drum in order to define the maximum reacted braking torque and pseudo-dynamic pressure distribution at the transition point between sticking and sliding motion. The method clearly illustrates the changes in contact force that take place as a function of the applied pressure, coefficient of friction and initial gap between lining and rotor. These changes in contact area are shown to influence the overall stability and therefore squeal propensity of the brake assembly.
Technical Paper

Improving Performance of a 6×6 Off-Road Vehicle Through Individual Wheel Control

2002-03-04
2002-01-0968
This paper presents a method of control for a 6×6 series-configured Hybrid Electric Off-road Vehicle (HEOV). The vehicle concerned is an eight-tonne logistics support vehicle which utilizes Hub Mounted Electric Drives (HMED) at each of its six wheel stations. This set-up allows Individual Wheel Control (IWC) to be implemented to improve vehicle handling and mobility. Direct Yaw-moment Control (DYC) is a method of regulating individual wheel torque to control vehicle yaw motion, providing greater stability in cornering. When combined with both a Traction Control System (TCS) and an Anti-lock Braking System (ABS) the tire/road interaction is fully controlled, leading to improved control over vehicle dynamics, whilst also improving vehicle safety.
Technical Paper

Development and Analysis of a Prototype Controllable Suspension

1997-08-06
972691
Persisting concerns regarding ride comfort, directional stability and more recently road damage have caused the manufacturers of commercial vehicles to consider controllable suspension systems. An electronically controllable adaptive suspension that comprises a variable spring rate system, switchable damping and load levelling is proposed as a cost-effective solution. This paper describes the aforementioned system and provides an outline of the design scheme for a prototype system; practical issues such as system configuration/detail, control system requirements, etc., are discussed. The system is evaluated analytically and both ride and handling modes are examined. In conclusion, performance capabilities are defined and cost-benefit issues addressed.
X