Search Results

The global transportation industry, and road freight in particular, faces formidable challenges in reducing Greenhouse Gas (GHG) emissions; both Europe and the US have already enabled legislation with CO2 / GHG reduction targets. In Europe, targets are set on a fleet level basis: a CO2 baseline has already been established using Heavy Duty Vehicle (HDV) data collected and analyzed by the European Environment Agency (EEA) in 2019/2020. This baseline data has been published as the reference for the required CO2 reductions. More recently, the EU has proposed a Zero Emissions Vehicle definition of 3g CO2/t-km. The Zero Emissions Vehicle (ZEV) designation is expected to be key to a number of market instruments that improve the economics and practicality of hydrogen trucks. This paper assesses the permissible amount of carbon-based fuel in hydrogen fueled vehicles – the Pilot Energy Ratio (PER) – for each regulated subgroup of HDVs in the baseline data set.

The medium and heavy-duty powertrain industry trend is to reduce reliance on diesel fuel and is aligned with continued efforts of achieving ultra-low emissions and high brake efficiencies. Compression Ignition (CI) of late cycle Directly Injected (DI) Natural Gas (NG) shows the potential to match diesel performance in terms of brake efficiency and power density, with the benefit of utilizing a lower carbon content fuel. A primary challenge is to achieve stable ignition of directly injected NG over a wide engine speed and load range without the need for a separate ignition source. This project aims to demonstrate the CI of DI NG through experimental studies with a Single Cylinder Research Engine (SCRE), leading to the development of a mono-fueled NG engine with equivalent performance to that of current diesel technology, 25% lower CO2 emissions, and low engine out methane emissions.

A constant volume spray and combustion vessel utilizing the pre-burn mixture procedure to generate pressure, temperature, and composition characteristic of near top dead center (TDC) conditions in compression ignition (CI) engines was modified with post pre-burn gas induction to incorporate premixed methane gas prior to diesel injection to simulate processes in dual fuel engines. Two variants of the methane induction system were developed and studied. The first used a high-flow modified direct injection injector and the second utilized auxiliary ports in the vessel that are used for normal intake and exhaust events. Flow, mixing, and limitations of the induction systems were studied. As a result of this study, the high-flow modified direct injection injector was selected because of its controlled actuation and rapid closure. Further studies of the induction system post pre-burn were conducted to determine the temperature limit of the methane auto-ignition.

With environmental policies becoming ever more stringent, there is heightened interest in natural gas (NG) as a viable fuel for medium to heavy duty engines. Typically, the industry has seen minor changes to the base engine when converting to run on NG, which, in turn historically provides degraded performance. In utilizing the positive properties of NG, Westport Fuel Systems has developed the High Efficiency Spark Ignition (HESI) combustion technology that has been shown to significantly improve performance. The HESI technology leverages a proven combustion system that is capable of generating a knock resistant charge motion while cooling the flame face. In conjunction with high boost for driving high pressure exhaust gas recirculation (EGR), this technology demonstrates the possibility for downsizing strategies while maintaining performance.

High-pressure direct-injection (HPDI) in heavy duty engines allows a natural gas (NG) engine to maintain diesel-like performance while deriving most of its power from NG. A small diesel pilot injection (5-10% of the fuel energy) is used to ignite the direct injected gas jet. The NG burns in a predominantly non-premixed combustion mode which can produce particulate matter (PM). Here we study the effect of injection strategies on emissions from a HPDI engine in two parts. Part-I will investigates the effect of late post injection (LPI) and Part II will study the effect of slightly premixed combustion (SPC) on emission and engine performance. PM reductions and tradeoffs involved with gas late post-injections (LPI) was investigated in a single-cylinder version of a 6-cylinder,15 liter HPDI engine. The post injection contains 10-25% of total fuel mass, and occurs after the main combustion event.

High-pressure direct-injection (HPDI) in heavy duty engines allows a natural gas (NG) engine to maintain diesel-like performance while deriving most of its power from NG. A small diesel pilot injection (5-10% of the fuel energy) is used to ignite the direct injected gas jet. The NG burns in a predominantly mixing-controlled combustion mode which can produce particulate matter (PM). Here we study the effect of injection strategies on emissions from a HPDI engine in two parts. Part-I investigated the effect of late post injection (LPI); the current paper (Part-II) reports on the effects of slightly premixed combustion (SPC) on emission and engine performance. In SPC operation, the diesel injection is delayed, allowing more premixing of the natural gas prior to ignition. PM reductions and tradeoffs involved with gas slightly premixed combustion was investigated in a single-cylinder version of a 6-cylinder, 15 liter HPDI engine.

Natural gas offers the potential to reduce greenhouse gas emissions from heavy-duty on-road transportation. One of the challenges facing natural gas as a fuel is that its composition can vary significantly between different fuel suppliers and geographical regions. In this work, the impact of fuel composition variations on a heavy-duty, direct injection of natural gas engine with diesel pilot ignition is evaluated. This combustion process results in a predominantly non-premixed gaseous fuel combustion event; as a result, end-gas autoignition (knock) is not a concern. Changes in the fuel composition do still impact the combustion, both through the changes in the chemical kinetics of the reactions and due to changes in the density of the fuel. Increasing concentrations of heavier hydrocarbons, such as ethane or propane, in the fuel lead to higher fuel densities and hence greater fuel mass being injected for a given injection duration.

An ultrahigh injection pressure, common rail fuel injection system was designed, fabricated, and evaluated. The result was a system suitable for high-power density diesel engine applications. The main advantages of the concept are a very short injection duration capability, high injection pressure independent of engine speed, a simplified electronic control valve, and good packaging flexibility. Two prototype injectors were developed. Tests were performed on an injector flow bench and in a single cylinder research engine. The first prototype delivered 320 mm3 within 2.5 milliseconds with a 2600 bar peak injection pressure. A conventional minisac nozzle was used. The second prototype employed a specially designed pintle nozzle producing a near-zero cone angle liquid jet impinging on a 9-mm cylindrical target centered on the piston bowl crown (OSKA-S system). The second prototype had the capability to deliver 316mm3 in 0.97ms.

The benefits of direct cylinder fuel injection to the fuel economy and exhaust emissions of small spark ignited two-stroke engines is well known. The selection of a commercially viable fuel injection solution continues to receive evaluation and scrutiny by the engine manufacturers. This paper describes the development and demonstration of an EDFI solution which is applicable to low cost and high production volume engines in several industries. The system is based on the “accumulator” fuel injection operating principle, which involves pressurizing fuel within an injection nozzle and subsequently releasing the pressurized fuel into the combustion chamber on command. This concept provides very short injection duration throughout the dynamic operating range of the engine as well as high injection frequency capability.

Hydraulically intensified medium pressure common rail (MPCR) electronic fuel injection systems are an attractive concept for heavy-duty diesel engine applications. They offer excellent packaging flexibility and thorough engine management system integration. Two different concepts were evaluated in this study. They are different in how the pressure generation and injection events are related. One used a direct principle, where the high-pressure generation and injection events occur simultaneously producing a near square injection rate profile. Another concept was based on an indirect principle, where potential energy (pressure) is first stored inside a hydraulic accumulator, and then released during injection, as a subsequent event. A falling rate shape is typically produced in this case. A unit pump, where the hydraulic intensifier is separated from the injector by a high-pressure line, and a unit injector design are considered for both concepts.

Direct injection has been considered the most effective approach to overcome the inherent short-circuiting of fuel in a two-stroke engine. A practical application of this technology on an 1100cc personal watercraft (PWC) engine is described. The experimental results show a drastic improvement in the engine emissions and fuel economy while maintaining good output performance and drive-ability of the PWC tested. The all-electronic, direct fuel injection engine has demonstrated a 76.3% reduction in hydrocarbon (HC) emissions and 43.03 g/kW-h HC plus oxides of nitrogen (NOx) emissions. This HC + NOx level meets the emission standards applicable to the 2006 model year set by the Environmental Protection Agency (EPA) for new gasoline spark-ignition marine engines. Finally some considerations on extending the technology to include combustion control in the areas of both air and spark management, are recommended.

Natural gas is a low cost, abundant and clean burning fuel. Current internal combustion engines can be readily adapted to use natural gas fuel either in conjunction with conventional liquid fuels or as dedicated systems. Use of modern electronic controls allows consideration of new engine management strategies that are not practical or even possible with mechanical systems. The preferred approach is pre-mixed lean burn with cylinder-by-cylinder fuel injection and full time control of optimized air/fuel ratio and ignition.

Dual-fuel pilot ignited natural gas engines have several intrinsic advantages relative to spark ignited; mainly higher thermal efficiency and lower conversion costs. The major drawback is associated with light loads. This paper discusses objectives, approaches, methods and results of the development of strategies which overcome the drawbacks and enhance the advantages. Development of a pilot fuel injection system, having a delivery of only 1 mm3 at a duration of 0.6 ms, was described in a previous paper. This paper concentrates on the results of strategies to reduce unburned methane in the exhaust and to increase the substitution of gas at light loads through skip-fire, by-passing boost air and exhaust gas recirculation techniques. Engine tests proved that with these strategies, diesel fuel replacement of more than 95% over the entire engine operating map, including idle, can be achieved and current and anticipated future emission standards satisfied.

The paper discusses objectives, approaches and results of the development of a pilot fuel injection system (FIS) for a dedicated, compression ignition, high-speed, heavy duty natural gas/diesel engine. The performance of the pilot FIS is crucial for the success of a dual fuel concept. The Servojet electro-hydraulic, accumulator type fuel system was chosen for the pilot fuel injection. An alternative pilot FIS based on the “water hammer” (WH) effect was also considered. The modifications to a stock 17 min injector is described. Three different types of pilot injector nozzle were investigated: standard Valve Covered Orifice (VCO), modified minisac and new designed, unthrottled pintle. Preliminary results from engine tests proved that the optimum pilot fuel quantity is the minimum quantity. Based on that finding, the pilot FIS design was further optimized.

The need for a natural gas conversion kit for heavy-duty engines which provides equivalent gasoline performance as well as acceptable exhaust emissions has prompted the use of turbocharged lean-burn engine technology. Turbocharged lean-burn strategy allows operation which meets current heavy-duty emission requirements without the need for a catalytic converter. To insure proper fuel distribution during lean-burn operation, the system includes multi-point sequential fuel injection, fully mapped lambda control, deceleration fuel cut-off, part load cylinder deactivation, and fuel charge stratification. This paper documents the design and development of a General Motors turbocharged, sequential fuel injected, leanburn natural gas engine based on the 4.3L truck engine.

Studies of the physical and combustion properties of saturated hydrocarbon gaseous fuels have shown that there is a remarkable correlation between these properties and the hydrogen to carbon ratio of the fuel molecules. If the correlation is limited to the four most prevalent constituents of natural gas fuels, i.e., methane (CH4), ethane (C2 H6), propane (C3H8) and butane (C4H10), it appears that the flow and combustion characteristics of the pure gases and mixtures of these same gases can be predicted from the H/C ratio alone, independent of the various proportions of the gases. It was concluded that if the H/C ratio of a mixture of gases could be determined by means of an on-line dynamic sensor, important engine and fuel management parameters, such as octane no., methane no., density, stoichiometric air/fuel ratio, etc. could be determined and compensated for by an electronic control unit.

Increasing emphasis on natural gas as a clean, economical, and abundant fuel, encourages the search for the optimum approach to management of fuel, air and combustion to achieve the best results in power, fuel economy and low exhaust emissions. Electronic injection of fuel directly into the throttle body, intake ports or directly into the cylinder offers important advantages over carburetion or mixing valves. This is particularly true in the case of installations in which the gas supply is available at several atmospheres pressure above maximum intake manifold pressure. The use of choked-flow pulse- width-modulated electronic injectors offers precision control over the engine operating range with a wide variety of options for both stoichiometric and lean bum applications. A complete system utilizing commercially available components together with the application, calibration and engine mapping techniques is described.

Through the joint efforts of BKM, SPI, AFS and Belarus, an advanced, all- electronic dual fuel system has been developed for retrofit applications on the Belarus D-144, four-cylinder, 4.15 liter, 44.7 KW diesel engine. The system features all electronic control on both full diesel or up to 90 % gas with automatic and instant changeover capability. The existing mechanical diesel injection system was replaced with an all electronic, hydraulically actuated, diesel injection system coupled with timed multi-point electronic injection for the gas system. The control strategy does not utilize inlet throttling typically used on gas fueled engines. The effectiveness of this simplified control system is assumed to be the result of a degree of charge stratification. The D-144 engine is utilized in a wide variety of industrial, farm and highway applications. Special application requirements can be accommodated by programming the EPROM control chip.

An electronic fuel injection system for diesel engines has been adapted for dual fuel applications. The simplified and commercially practical system capitalizes on using standardized hardware and software modified for the dual fuel conversion kit Using the conventional diesel pump for pilot injection, electronic injectors provide timed pulses of gas for each cylinder. The system has been successfully applied to both naturally aspirated and turbocharged versions of the Mercedes OM-352 diesel engine and has been placed in service in transit bus applications. Performance data shows over 90% displacement of diesel fuel with the same power and fuel economy as the base diesel engine. Initial reports from the field indicate excellent performance and drivability as well as smoke-free exhaust when in the dual fuel mode.

Additional data has been analyzed on the effect of engine size on thermal efficiency. The comparison has been expanded to show the trends separately for engines developed by several different manufacturers. The data confirm the conclusion that engines below 2.0 liters per cylinder seem to deteriorate in fuel economy faster than would have been predicted from the behavior of larger engines. It is postulated that such deterioration results from a combination of less than optimum fuel spray, wall wetting, and perhaps a greater heat transfer loss than was anticipated. The paper focuses on engines in the size range under two liters per cylinder and addresses some of the problems to be resolved. Means for generating and controlling fuel spray and injection rate shape are presented along with experimental data on fuel sprays and engine combustion.