Refine Your Search

Date

Date

Topic

Topic

Energy conservation Research and development Lightweighting Maintenance and Aftermarket A-5A Wheels, Brakes and Skid Controls Committee

Search Results

Viewing 1 to 19 of 19
1
Sort by published
Standard

Overpressurization Release Devices
2024-01-16
WIP
ARP1322D
This SAE Aerospace Recommended Practice (ARP) specifies the minimum design and qualification test recommendations for aircraft wheel overpressurization release devices used with tubeless aircraft tires to protect from possible explosive failure of the contained inflation chamber due to overinflation. Devices of this type provide a means, but not the only means, for showing compliance to Subsection 25.731(d) of Part 25 of Title 14 of the Code of Federal Regulations. Devices of this type will not protect against flash fire explosive conditions within the inflation chamber which may occur due to extremely overheated brakes or spontaneous combustion caused by a foreign substance within the inflation chamber. To help protect against this condition, nitrogen (N2) or other inert gas should be used for inflation.
Standard

Aircraft Brake Temperature Monitoring
2021-10-28
CURRENT
ARP6812
This SAE Aerospace Recommended Practice (ARP) provides recommendations for the function, design, construction, and testing of an on-aircraft Brake Temperature Monitoring System (BTMS), sometimes referred to as a Brake Temperature Indication System (BTIS). NOTE: This ARP does not address: Cockpit ergonomics and Aircraft operating procedures. Various handheld methods of temperature sensing or readouts, as these are not associated with transport aircraft during normal operation. Temperature sensitive paints as a means to indicate exceedance of a landing gear axle temperature threshold due to brake temperature.
Standard

Minimum Environmental Performance Standard for Parts 23, 25, 27, and 29 Aircraft Wheels Brakes, and Wheel and Brake Assemblies
2021-04-27
WIP
AS6961
This SAE Aerospace Standard (AS) prescribes the Minimum Performance Standards (MPS) for environmental conditions that wheel, brake, and wheel and brake assemblies to be used on aircraft certificated under 14 CFR Parts 23, 25, 27, and 29. The environmental requirements in this document shall be used in conjunction with other MPS defined in Technical Standard Orders for the applicable equipment.
Standard

Carbon Brake Contamination and Oxidation
2016-04-12
CURRENT
AIR5490A
This document provides information on contamination and its effects on brakes having carbon-carbon composite friction materials (carbon). Carbon is hygroscopic and porous, and therefore readily absorbs liquids and contaminants. Some of the contaminants can impact intended performance of the brake. This document is intended to raise awareness of the effects of carbon brake contamination and provide information on industry practices for its prevention. Although not addressed in this report, contaminants can cause problems with other landing system components including tires.
Standard

Test Method for Catalytic Carbon Brake Disk Oxidation
2013-12-04
WIP
AS6289
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This test is designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions.
Standard

Test Method for Catalytic Carbon Brake Disk Oxidation
2013-03-11
WIP
AIR5567B
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This simple test is only designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions. It is not possible to set a general acceptance threshold oxidation limit based on this test method because carbon brake stack oxidation is a function of heat sink design and the operating envirnoment.
Standard

Thermal Sensitive Inflation Pressure Release Devices for Tubeless Aircraft Wheels
2012-05-09
HISTORICAL
AS707B
This standard establishes minimum design, installation, qualification, and operational requirements for thermally actuated, pressure release devices for use only in tubeless tire type aircraft wheels. These devices are designed to completely release the contained inflation pressure from a tubeless tire and wheel assembly when brake generated heat causes the assembly to exceed a safe temperature operating level. The objective is to prevent tire or wheel rupture due to brake generated heat which could cause serious personnel injuries or serious aircraft operational hazards.
Standard

Test Method for Catalytic Carbon Brake Disk Oxidation
2009-05-13
HISTORICAL
AIR5567
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This simple test is only designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions. It is not possible to set a general acceptance threshold oxidation limit based on this test method because carbon brake stack oxidation is a function of heat sink design and the operating envirnoment.
Standard

Aircraft Tire Inflation-Deflation Equipment
2008-06-16
HISTORICAL
AS1188
This specification covers minimum design and test requirements for aircraft tire inflation-deflation equipment for use on all types of aircraft. It shall be the responsibility of the airframe manufacturer to determine the compatibility of the requirement with the applicable aircraft and to specify requirements in excess of these minimums as necessary.
Standard

Skid Control Equipment
2007-12-12
HISTORICAL
AS483B
This standard covers minimum requirements for skid control equipment for use on all types and models of civil aircraft. It shall be the responsibility of the applicant to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
Standard

THERMAL SENSITIVE INFLATION PRESSURE RELEASE DEVICES FOR TUBELESS AIRCRAFT WHEELS
1988-12-01
HISTORICAL
AS707
This standard establishes minimum design, installation, qualification, and operational requirements for thermally actuated, pressure release devices for use only in tubeless tire type aircraft wheels. These devices are designed to completely release the contained inflation pressure from a tubeless tire and wheel assembly when brake generated heat causes the assembly to exceed a safe temperature operating level. The objective is to prevent tire or wheel rupture due to brake generated heat which could cause serious personnel injuries or serious aircraft operational hazards.
Standard

THERMAL SENSITIVE PRESSURE RELEASE DEVICES FOR TUBELESS AIRCRAFT WHEELS
1982-04-01
HISTORICAL
AS707A
This standard establishes minimum design, installation, qualification, and operational requirements for thermally actuated, pressure release devices for use only in tubeless tire type aircraft wheels. These devices are designed to completely release the contained air pressure from a tubeless tire and wheel assembly when absorbed and/or brake generated heat causes the tire or wheel to exceed a safe pressure/temperature/load operating level. The objective is to prevent tire or wheel rupture from brake generated heat which could cause serious personnel injuries or serious aircraft operational hazards.
Standard

SKID CONTROL EQUIPMENT
1975-01-15
HISTORICAL
AS483A
This standard covers minimum requirements for skid control equipment for use on all types and models of civil aircraft. It shall be the responsibility of the applicant to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
1
X