Refine Your Search

Topic

Search Results

Standard

Coiled Tubing – Titanium Alloy, Hydraulic Applications, Aerospace

2018-06-21
CURRENT
ARP4146D
This SAE Aerospace Recommended Practice (ARP) addresses the design, installation, and testing of coiled tube assemblies using Ti-3Al-2.5V cold worked, stress relieved (CWSR) tubing per AMS4945. It specifically details five different configurations of coiled tubing. The configurations detailed herein should be compatible with pressure levels up to 8000 psi (55.2 MPa) upon completion of analysis for the actual stress and life requirement of the intended application. Formal qualification tests are recommended to verify satisfactory installation, clamping, and the life of each unique design. NOTE: For information on design of coiled tube assemblies using CRES steel tubing, see ARP584.
Standard

Coiled Tubing - Corrosion Resistant Steel, Hydraulic Applications, Aerospace

2017-06-16
CURRENT
ARP584D
This SAE Aerospace Recommended Practice (ARP) addresses the design, installation, and testing of coiled tube assemblies ranging from 1/4 inch (6.3 mm) to 1.0 inch (25 mm) diameter using CRES tubing per AMS-T-6845, unless otherwise approved by the Procuring Activity. This ARP specifically details three different configurations of coiled tubing. These configurations should be compatible with pressure levels up to 3000 psi (20.7 MPa) upon the completion of the analysis for the actual stress and life requirement of the intended application. However, formal qualification tests are recommended to verify the satisfactory installation, clamping, and the life of each unique design. NOTE: Refer to ARP4146 for information on design of coiled tube assemblies using Titanium tubing.
Standard

Design of Tubing Installations for Aerospace Hydraulic Systems

2016-11-17
CURRENT
ARP994B
This document provides recommended practices for the design and selection of tube, hose, and fitting systems that are used to transmit hydraulic fluid on aircraft. NOTE: Guidance for the sizing of hydraulic tubing is contained in Appendix A.
Standard

Reducers, Pneumatic Pressure, Missile

2014-10-06
CURRENT
AS1297B
The complete specification for a pneumatic pressure reducer for high pressure pneumatic systems used in missiles comprises: (1) this standard, which includes many of the general performance requirements, (2) a detailed procurement specification describing envelope and operating conditions, and (3) the "Pneumatic Components, Aeronautical - General Specification For - MIL-P-8564" which covers general requirements common to all components for use in high pressure pneumatic systems.
Standard

Coiled Tubing – Titanium Alloy, Hydraulic Applications, Aerospace

2012-12-12
HISTORICAL
ARP4146C
This SAE Aerospace Recommended Practice (ARP) addresses the design, installation, and testing of coiled tube assemblies using Ti-3Al-2.5V cold worked, stress relieved (CWSR) tubing per AMS4945. It specifically details five different configurations of coiled tubing. The configurations detailed herein should be compatible with pressure levels up to 8000 psi (55.2 MPa) upon completion of analysis for the actual stress and life requirement of the intended application. Formal qualification tests are recommended to verify satisfactory installation, clamping, and the life of each unique design. NOTE: For information on design of coiled tube assemblies using CRES steel tubing, see ARP584.
Standard

Recommended Practice for the Design of Tubing Installations for Aerospace Fluid Power Systems

2012-08-22
HISTORICAL
ARP994A
This document provides recommended practices for the design of tubing systems that are used for the transmission of liquid and gasses in fluid power systems for aerospace vehicles such as aircraft, missiles and boosters. The primary emphasis is given to recommended practices for line sizing, tube routing, supports and clamping, stress considerations and permissible defects, and provisions for flexure through the use of flexible hoses, coiled tubes, swivel joints, and expansion glands. The sections regarding tubing materials and fitting types are included for reference, but particular recommendations are purposely avoided since their selection is dependent upon the specific requirements of each particular vehicle system and many other factors.
Standard

Coiled Tubing - Corrosion Resistant Steel, Hydraulic Applications, Aerospace

2012-01-17
HISTORICAL
ARP584C
This SAE Aerospace Recommended Practice (ARP) addresses the design, installation, and testing of coiled tube assemblies ranging from 1/4 inch (6.3 mm) to 1.0 inch (25 mm) diameter using CRES tubing per AMS-T-6845, unless otherwise approved by the Procuring Activity. This ARP specifically details three different configurations of coiled tubing. These configurations should be compatible with pressure levels up to 3000 psi (20.7 MPa) upon the completion of the analysis for the actual stress and life requirement of the intended application. However, formal qualification tests are recommended to verify the satisfactory installation, clamping, and the life of each unique design. NOTE: Refer to ARP4146 for information on design of coiled tube assemblies using Titanium tubing.
Standard

Coiled Tubing – Titanium Alloy, Hydraulic Applications, Aerospace

2011-11-28
HISTORICAL
ARP4146B
This SAE Aerospace Recommended Practice (ARP) addresses the design, installation, and testing of coiled tube assemblies using Ti-3Al-2.5V cold worked, stress relieved (CWSR) tubing per AMS4945. It specifically details five different configurations of coiled tubing. The configurations detailed herein should be compatible with pressure levels up to 8000 psi (55.2 MPa) upon completion of analysis for the actual stress and life requirement of the intended application. Formal qualification tests are recommended to verify satisfactory installation, clamping, and the life of each unique design. NOTE: For information on design of coiled tube assemblies using CRES steel tubing, see ARP584.
Standard

Aerospace-Hydraulic Switching Valve, Pressure or Pilot Operated

2008-02-07
CURRENT
ARP4741
This SAE Aerospace Recommended Practice (ARP) establishes the requirements for the design, manufacture, and qualification of four hydraulic switching valves used in airborne applications. Two are pressure operated, Type IA and IB and two are solenoid/pilot operated, Type IIA and IIB. They are applicable to four pressure classes 3000, 4000, 5000 and 8000 psi. The equipment as designed is intended to be installed in hydraulic systems designed to AS5440 for military applications or ARP4752 and ARP4925 depending on the type of aircraft for commercial applications. Additional or refined requirements shall be contained in the detail (procurement) specification and these shall take precedence over any potentially conflicting requirements of this ARP or documents referenced by this ARP.
Standard

Aerospace-Solenoid Valve, Hydraulic, Three Way, Two Position, Direct Acting

2003-09-27
CURRENT
ARP4945A
This SAE Aerospace Recommended Practice (ARP) is intended as a guide to aid in the specifying and testing of direct acting three way, two position, single and multiple coil, normally open and normally closed solenoid valves used for the pilot actuation of hydraulic control systems and the control of hydraulic components. The information presented should be useful in standardizing terminology, in specifying requirements and performance parameters, and in defining test methods. The recommendations do not restrict or attempt to define the internal design features of solenoid valves. Standard mechanical, electrical and fluid porting interfaces are recommended to provide commonalty, interchangeability, design flexibility and to be more affordable. In general, this recommended practice is directed toward solenoid valves for use in military and commercial flight control and hydraulic actuation systems.
Standard

Solenoid, Electrical, General Specification For

2000-11-01
CURRENT
AS40401
This specification covers the general requirements for electrical solenoids used to actuate various devices through the conversion of electrical signals into mechanical motion. These solenoids are of the axial stroke type and the rotary stroke type.
Standard

Aerospace - Valves, Check, Hydraulic, Aircraft and Missile

2000-10-01
CURRENT
ARP4946
This SAE Aerospace Recommended Practice (ARP) establishes the general requirements for spring-loaded, normally closed check valves for use in Type I, Type II, or Type III aircraft and missile hydraulic systems having nominal operating pressure shown in Table 1.
Standard

Coiled Tubing - Titanium Alloy, Hydraulic Applications, Aerospace

2000-01-01
HISTORICAL
ARP4146A
This SAE Aerospace Recommended Practice (ARP) specifically discusses five configurations of flexible tubing. The design data given will aid in design of coiled tube assemblies using Ti-3Al-2.5V cold worked, stress relieved (CWSR) tubing per AMS 4945. The configurations discussed should be compatible with pressure levels up to 8000 psi (55.2 MPa) upon completion of analysis for the actual stress and life requirement of the intended application. Formal qualification tests are recommended to verify satisfactory installation, clamping, and life of each unique design.
Standard

Aerospace-Solenoid Valve, Hydraulic, Three Way, Two Position, Direct Acting

1997-11-01
HISTORICAL
ARP4945
This SAE Aerospace Recommended Practice (ARP) is intended as a guide to aid in the specifying and testing of direct acting three way, two position, single and multiple coil, normally open and normally closed solenoid valves used for the pilot actuation of hydraulic control systems and the control of hydraulic components. The information presented should be useful in standardizing terminology, in specifying requirements and performance parameters, and in defining test methods. The recommendations do not restrict or attempt to define the internal design features of solenoid valves. Standard mechanical, electrical and fluid porting interfaces are recommended to provide commonalty, interchangeability, design flexibility and to be more affordable. In general, this recommended practice is directed toward solenoid valves for use in military and commercial flight control and hydraulic actuation systems.
Standard

Coiled Tubing, Corrosion Resistant Steel, Hydraulic Applications, Aerospace

1996-09-01
HISTORICAL
ARP584B
This SAE Aerospace Recommended Practice (ARP) encompasses design, analysis, fabrication, and installation of pressurized metal tubing used in fluid power systems to provide relative motion. Specific data given are for MIL-T-6845 tubing ranging from 1/4 to 1 in (6.3 to 25 mm) to diameter used in 3000 psi (20.7 MPa) hydraulic or pneumatic system, Military Type I, II, III, or IV hydraulic systems applied to any type of vehicle. For information on design of coiled tube assemblies using Ti-3Al-2.5CWSR tubing, see ARP4146. The flexible configurations of tubing are intended for application to actuators that oscillate about a pivot, to areas of large structural deflection such as reservoirs installation, and to areas of extreme environment where flexible hose could not survive.
Standard

Reducers, Pneumatic Pressure, Missile

1994-12-01
HISTORICAL
AS1297A
The complete specification for a pneumatic pressure reducer for high pressure pneumatic systems used in missiles comprises: (1) this standard, which includes many of the general performance requirements, (2) a detailed procurement specification describing envelope and operating conditions, and (3) the "Pneumatic Components, Aeronautical - General Specification For - MIL-P-8564" which covers general requirements common to all components for use in high pressure pneumatic systems.
X