Search Results

This SAE Aerospace Standard describes the system used by passenger boarding stairs (PBS) mobile passenger boarding ramps (PBS) and boarding bridges (PBB) to inform on-board cabin crew about the docking status of the PBS/PBR/PBB and whether it is positioned such that it is safe to open the aircraft door. Current practice calls for the PBS/PBR/PBB operator to knock on the aircraft door to inform the cabin crew that it is safe to open the aircraft door. New technologies being incorporated into PBS/PBR/PBB such as remote control systems and autonomous driving vehicles are entering the market. As such, new/updated controls and/or procedures are necessary to ensure continuing safe operations.

The data in this document is, at this stage, primarily concerned with the interface of pallet/container loaders and lower-deck compartments of standard and wide-body aircraft although the principles illustrated may be applied to the main-decks of narrow and wide-body aircraft. NOTE: For the purpose of this document, in accordance with Part 3 of the Directives for the technical work of ISO and with accepted IATA practice, minimum essential criteria defined by the word "shall" are absolute requirements. Recommended criteria identified by the word "should", while considered important, are not mandatory.

This SAE Aerospace Information Report (AIR) covers, and is restricted to, hands-on servicing/ maintenance of industrial lead acid batteries used solely for motive power and exclusively for ground support equipment (GSE). It does not address or pertain to automotive-type SLI (starting-lighting-ignition) batteries or any other types of batteries (such as nickel-cadmium, zinc, or lithium batteries) which may be on-board airport GSE for either motive power or auxiliary uses. Similarly, the battery servicing and charging facilities described herein are those intended exclusively for industrial lead acid batteries.

This SAE Aerospace Recommended Practice (ARP) describes three general types of Ground Support Equipment (GSE) battery chargers. The battery charger typically requiring up to 8 hours to recharge a 100% discharged battery, hereafter called “Conventional Charger.” A charger, hereafter called “Opportunity Charger,” which has the ability to charge at a slightly faster rate than a conventional charger. A charger, hereafter called “Fast Charger,” which has the ability to charge at a much faster rate than a conventional charger. Recommendations that apply to all types will refer generically to “charger.”

This Aerospace Recommended Practice includes the following areas: basis for system requirements; selection of materials coupled with hazards and safety; configuration of design; system operation; and evaluation testing.

The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.

This SAE Aerospace Recommended Practice (ARP) describes two general types of Ground Support Equipment (GSE) battery chargers. The conventional industrial battery charger typically requiring up to 8 hours to recharge a 100% discharged battery, hereafter called “Conventional Charger”. The other type a fast battery charger typically used as an opportunity charger for ground support equipment, hereafter called “Fast Charger”. Recommendations that apply to both types will refer generically to “charger”.

The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852A and ARP4853A. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, reduce the certified safe life limit of the nose gear, or induce a stability problem during pushback and/or maintenance towing operations. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only. It is not meant for dispatch (operational) towing (see definitions in Section 3). Dispatch towing imposes greater loads on nose gears and structure due to additional passenger, cargo, and fuel loads.

The primary purpose of a Propellant Transfer Unit (PTU) is to temperature-condition and weigh a specific amount of propellant, and transfer if to a vehicle propellant tank. A secondary purpose of a PTU may be to drain propellant from the vehicle tank and return it to the transfer unit when required. The transfer unit may also be used for flushing the vehicle fill lines and transfer unit with appropriate flushing fluids, followed with nitrogen for the purpose of drying the lines and weigh tank. The transfer unit may include provisions for helium purging of the propellant transfer tank and lines, ad supplying a blanket of helium pressure to the transfer tank. Each PTU consists of a piping system with appropriate propellant and pneumatic valves, regulators, relief valves, filters and a propellant pump. Various components such as a scrubber, bubbler, propellant cooler (heat exchanger), propellant weigh tank, weigh scale and a chiller may make up the balance of the assembly.

This SAE Aerospace Recommended Practice (ARP) describes an industrial battery charger, solid state type, hereafter called charger, for use in charging lead acid batteries in ground support equipment.

This recommended practice describes an industrial battery charger, solid state type, hereafter called charger, for use in charging lead acid batteries in ground support equipment.

This recommended practice describes an industrial battery charger, solid state type, hereafter called charger, for use in charging lead acid batteries in ground support equipment.

This Aerospace Recommended Practice includes the following areas: basis for system requirements; selection of materials coupled with hazards and safety; configuration of design; system operation; and evalua tion testing.