Refine Your Search

Date

Date

Topic

Topic

Control systems Connectors and terminals Identification numbers Electrical systems AGE-3 Aircraft Ground Support Equipment Committee

Search Results

Viewing 1 to 20 of 64
123Next >Last >>
Sort by published
Standard

Passenger Access Means Docking Indicator for Cabin Crew
2022-05-02
CURRENT
AS7995
This SAE Aerospace Standard describes the system used by passenger boarding stairs (PBS) mobile passenger boarding ramps (PBS) and boarding bridges (PBB) to inform on-board cabin crew about the docking status of the PBS/PBR/PBB and whether it is positioned such that it is safe to open the aircraft door. Current practice calls for the PBS/PBR/PBB operator to knock on the aircraft door to inform the cabin crew that it is safe to open the aircraft door. New technologies being incorporated into PBS/PBR/PBB such as remote control systems and autonomous driving vehicles are entering the market. As such, new/updated controls and/or procedures are necessary to ensure continuing safe operations.
Standard

Electric Baggage/Cargo Tractor
2022-03-28
CURRENT
ARP1804B
This SAE Aerospace Recommended Practice (ARP) outlines the design and performance requirements for a battery-powered electric tow tractor for the handling of baggage or cargo trailers in airline service. The use of “shall” in this document indicates a mandatory requirement. The use of “should” indicates a recommendation or that which is advised but not required.
Standard

Pallet/Container Loader Auto-Levelling Systems
2021-09-30
CURRENT
ARP4776
The data in this document is, at this stage, primarily concerned with the interface of pallet/container loaders and lower-deck compartments of standard and wide-body aircraft although the principles illustrated may be applied to the main-decks of narrow and wide-body aircraft. NOTE: For the purpose of this document, in accordance with Part 3 of the Directives for the technical work of ISO and with accepted IATA practice, minimum essential criteria defined by the word "shall" are absolute requirements. Recommended criteria identified by the word "should", while considered important, are not mandatory.
Standard

Aircraft Tow Bar
2021-04-08
CURRENT
ARP1915E
This SAE Aerospace Recommended Practice (ARP) specifies dimensional and physical requirements of tow bar connections to tractor and aircraft (see Figure 1). It is applicable to all types of commercial transport category aircraft tow bar. The purpose of this SAE Aerospace Recommended Practice (ARP) is to standardize tow bar attachments to airplane and tractor according to the mass category of the towed aircraft, so that one tow bar head with different shear levels can be used for all aircraft that are within the same mass category and are manufactured in compliance with AS1614 or ISO 8267.
Standard

Aircraft Cargo Conveyor
2021-04-08
CURRENT
ARP1836C
This SAE Aerospace Recommended Practice (ARP) outlines the functional and design requirements for a b self-propelled belt conveyor for handling baggage and cargo at aircraft bulk cargo holds. Additional considerations and requirements may legally apply in other countries. As an example, for operation in Europe (E.U. and E.F.T.A.), the applicable EN standards shall be complied with.
Standard

Airport Electrical Power System Harmonics
2020-09-23
CURRENT
AIR5387
This SAE Aerospace Information Report (AIR) is intended to cover all airport 50 or 60 Hz electrical systems as well as all electrical utilization equipment that is attached to those systems.
Standard

Maintenance of Batteries and Battery Charging and Servicing Facilities
2020-09-23
CURRENT
AIR1898A
This SAE Aerospace Information Report (AIR) covers, and is restricted to, hands-on servicing/ maintenance of industrial lead acid batteries used solely for motive power and exclusively for ground support equipment (GSE). It does not address or pertain to automotive-type SLI (starting-lighting-ignition) batteries or any other types of batteries (such as nickel-cadmium, zinc, or lithium batteries) which may be on-board airport GSE for either motive power or auxiliary uses. Similarly, the battery servicing and charging facilities described herein are those intended exclusively for industrial lead acid batteries.
Standard

Method of Evaluating Pneumatic Ground Power Units
2020-09-23
CURRENT
AIR4545A
This SAE Aerospace Information Report (AIR) covers, and is restricted to, the behavior of air under conditions of critical and subcritical flow at temperatures less than 500 °F.
Standard

Charger for Battery Powered Ground Support Equipment
2020-09-23
CURRENT
ARP1816D
This SAE Aerospace Recommended Practice (ARP) describes three general types of Ground Support Equipment (GSE) battery chargers. The battery charger typically requiring up to 8 hours to recharge a 100% discharged battery, hereafter called “Conventional Charger.” A charger, hereafter called “Opportunity Charger,” which has the ability to charge at a slightly faster rate than a conventional charger. A charger, hereafter called “Fast Charger,” which has the ability to charge at a much faster rate than a conventional charger. Recommendations that apply to all types will refer generically to “charger.”
Standard

Electrical Connectors for Use in Battery Powered Ground Support Equipment
2020-09-23
CURRENT
ARP1892B
This SAE Aerospace Recommended Practice (ARP) describes a two-pole electric connector for use in battery powered ground support equipment, i.e., traction batteries. Alternatively, the connector can have two or more auxiliary contacts for auxiliary circuits. A handle may be added as an option to assist in connecting and disconnecting.
Standard

Aircraft Markings for Ground Support Equipment Alignment
2020-04-24
CURRENT
AS6896
The purpose of this document is to provide a standard for aircraft fuselage markings located at the doors used for ground servicing operations. These markings can be used by all GSE that will dock at the aircraft. These markings may be used for one or several phases of the GSE positioning relative to the aircraft process: GSE alignment during approach, GSE final docking, and GSE auto leveling. It is not the purpose of this standard to describe the different technologies, cameras, or other equipment that can be mounted on GSE to utilize these markings. The aircraft that may use these markings will have a fuselage diameter of 3 m or more.
Standard

Aircraft Jacking Pads Adapters and Sockets Design and Installation of
2019-03-29
CURRENT
AS8091A
This SAE Aerospace Standard (AS) provides requirements for design and installation of aircraft jacking pad adapters and the mating jack socket interface to permit use of standard jacking equipment to be used in civil and military transport aircraft. The adapter defined herein shall be the key interface between the aircraft and the aircraft jack(s).
Standard

Ground Support Equipment Electrical Systems
2018-09-27
CURRENT
AIR1336B
This SAE Aerospace Information Report (AIR) considers the following major areas: 1 major components and their ratings; 2 selection criteria for optimum design balance for electrical systems; 3 effects of operating conditions and environment on both maintenance and life of components; 4 trouble signals - their diagnosis and cure.
Standard

Chassis Mounted Lifts Used to Board Airline Passengers With Mobility Impairments
2014-03-11
CURRENT
ARP5141A
This SAE Aerospace Recommended Practice (ARP) is intended to recommend a minimum standard, for the design and manufacturer of a self-propelled, chassis mounted passenger boarding vehicle. The vehicle will permit safe operation while minimizing aircraft damage and personnel safety hazards associated with commercial aircraft boarding operations. The vehicle described is intended to be used for assisting wheelchair passengers and passengers with disabilities on and off aircraft with door sill heights of 60 in (152.4 cm) and above.
123Next >Last >>
X