Search Results

Elastomers have large reversible elastic deformation, good damping and high energy absorption capabilities. Due to these characteristics along with low cost of manufacturing, elastomeric components are widely used in many industries and applications, including in automobiles. These components are typically subjected to complex multiaxial and variable amplitude cyclic loads during their service life. Therefore, fatigue failure and life prediction are important issues in the design and analyses of these components. Availability of an effective CAE technique to evaluate fatigue damage and to predict fatigue life under complex loading conditions is a valuable tool for such analysis. This paper discusses a general CAE analytical technique for durability analysis and life prediction of elastomeric components. The methodology is then illustrated and verified by using experimental fatigue test results from an automobile cradle mount.

In this study a dynamic simulation was conducted on a forged steel crankshaft from a single cylinder four stroke engine. Finite element analysis was performed to obtain the variation of the stress magnitude at critical locations. The dynamic analysis resulted in the development of the load spectrum applied to the crankpin bearing. This load was then applied to the FE model and boundary conditions were applied according to the engine mounting conditions. Results obtained from the aforementioned analysis were then used in optimization of the forged steel crankshaft. Geometry, material, and manufacturing processes were optimized using different geometric constraints, manufacturing feasibility, and cost. The first step in the optimization process was weight reduction of the component considering dynamic loading. This required the stress range under dynamic loading not to exceed the magnitude of the stress range in the original crankshaft.

In this study a dynamic simulation was conducted on a crankshaft from a single cylinder four stroke engine. Finite element analysis was performed to obtain the variation of stress magnitude at critical locations. The pressure-volume diagram was used to calculate the load boundary condition in dynamic simulation model, and other simulation inputs were taken from the engine specification chart. The dynamic analysis was done analytically and was verified by simulation in ADAMS which resulted in the load spectrum applied to crank pin bearing. This load was applied to the FE model in ABAQUS, and boundary conditions were applied according to the engine mounting conditions. The analysis was done for different engine speeds and as a result critical engine speed and critical region on the crankshaft were obtained. Stress variation over the engine cycle and the effect of torsional load in the analysis were investigated.

Fatigue is the primary cause of failure of crankshafts in internal combustion engines. The cyclic loading conditions and the stress concentrations in the crank pin fillets are unavoidable, and can result in fatigue failure. The objectives of this study were to compare the fatigue behavior of forged steel and ductile iron crankshafts from a one-cylinder engine as well as to determine if the fatigue life of a crankshaft can be accurately estimated using fatigue life predictions. Monotonic tensile tests as well as strain-controlled fatigue tests were conducted using specimens machined from the crankshafts to obtain the monotonic and cyclic deformation behavior and fatigue properties of the two materials. The forged steel had higher tensile strength and better fatigue performance than the ductile cast iron. Charpy v-notch impact tests were also conducted using specimens machined from the crankshafts to obtain and compare the impact toughness of the materials.

An optimization study was performed on a steel forged connecting rod with a consideration for improvement in weight and production cost. Since the weight of the connecting rod has little influence on its total production cost, the cost and the weight were dealt with separately. Reduction in machining operations, achieved by change in material, was a significant factor in manufacturing cost reduction. Weight reduction was achieved by using an iterative procedure. Literature survey suggests cyclic loads comprised of static tensile and compressive loads are often used for design and optimization of connecting rods. However, in this study weight optimization is performed under a cyclic load comprising dynamic tensile load and static compressive load as the two extreme loads. Constraints of fatigue strength, static strength, buckling resistance and manufacturability were also imposed. The fatigue strength was the most significant factor in the optimization of the connecting rod.

A vehicle steering knuckle undergoes time-varying loadings during its service life. Fatigue behavior is, therefore, a key consideration in its design and performance evaluation. This research program aimed to assess fatigue life and compare fatigue performance of steering knuckles made from three materials of different manufacturing processes. These include forged steel, cast aluminum, and cast iron knuckles. In light of the high volume of forged steel vehicle components, the forging process was considered as base for investigation. Monotonic and strain-controlled fatigue tests of specimens machined from the three knuckles were conducted. Static as well as baseline cyclic deformation and fatigue properties were obtained and compared. In addition, a number of load-controlled fatigue component tests were conducted for the forged steel and cast aluminum knuckles. Finite element models of the steering knuckles were also analyzed to obtain stress distributions in each component.