Search Results

A decade ago, James, et.al. published a detailed study of the available NASS data on severe rear impacts, with findings that “… stiffened or rigid seat backs will not substantially mitigate severe and fatal injuries in rear impacts.” No field accident study has since been advanced which refutes this finding. Advocates of rigidized seat backs often point to specific cases of severe rear impacts in which MAIS 4+ injuries are associated with seat back deformation, coupled with arguments supporting stiffer seatback designs. These arguments are generally based upon laboratory experiments with dummies in normal seating positions. Recent field accident data shows that generally, in collisions where the majority of societal harm is created, yielding seats continue to provide benefits, including those associated with whiplash associated disorders (WAD).

The BSAN crash pulse model has been shown to provide useful information for restraint sensing evaluation and for structural force-displacement studies in flat fixed rigid barrier (FFRB) crashes. This paper demonstrates a procedure by which the model may be extended for use with central and offset vehicle to vehicle (VTV) crashes through appropriate combinations of vehicle parameters.

The original Malibu II study, conducted by Bahling et al, found that neck compression loading in rollover crashes is caused by the occupant moving toward the ground and therefore, roof crush was not causally related to the loading. Some have disputed this finding claiming that the occupant does not “dive toward the roof,” but rather, the roof “moves in” toward the occupant, and that roof deformation is the primary cause of cervical spine injuries in rollover crashes. The original study included a detailed analysis of film and force transducer data for 10 Potentially Injurious Impacts (PII's). This paper presents an independent analysis of these 10 PII's and one additional PII. This analysis uses the film and transducer data to evaluate the timing of roof deformation and neck loading, the magnitude of roof deformation at the time of peak neck load, and the motion of the vehicle and occupants in the inertial reference system.

Understanding of events within the history of a crash, and estimation of the severity of occupant interior collisions depend upon an accurate assessment of crash duration. Since this time duration is not measured independently in most crash test reports, it must usually be inferred from interpretations of acceleration data or from displacement data in high-speed film analysis. The significant physical effects related to the crash pulse are often essential in reconstruction analyses wherein the estimation of occupant interior “second collision” or airbag sensing issues are at issue. A simple relation is presented and examined which allows approximation of the approach phase and separation phase kinematics, including restitution and pulse width. Building upon previous work, this relation allows straightforward interpretation of test data from related publicly available test reports.

Field experience has consistently indicated that lap-only belts and lap-shoulder belts perform well and about equally in prevention of fatalities and serious injuries in the rear seating positions. Analyses based on overall usage and injury figures from the Fatal Analysis Reporting System (FARS), double-pair analysis of FARS data, and still older data bases have shown that, in the rear outboard seating positions, injury rates are about the same for lap-only and lap-shoulder belted crash occupants. Although sparse, recently available field data from the 1988-2001 National Analysis Sampling System / Crashworthiness Data System (NASS/CDS) files confirm the finding that, when used by rear seat occupants, lap-only belts perform about equally with lap-shoulder belts as countermeasures for serious and fatal injury in severe frontal crashes.

Recent cadaver studies have provided data for the development of force and stiffness characteristics of the side of the human head. A Hybrid III Anthropomorphic Test Dummy (ATD) head was modified to allow direct measurement of impact forces on the parietal and temporal regions by recasting the upper left half of the skull and installing triaxial piezoelectric force transducers. Dynamic impact tests of this modified head were conducted and force/stiffness characteristics for the temporal and parietal areas were compared to existing data on cadaver subjects. It was found that the existing Hybrid III vinyl skin satisfactorily represents the force/stiffness characteristics of the human head in these areas. This modified Hybrid III dummy head was also impacted against typical interior components likely to be contacted during a side impact. The force and acceleration test results are presented.

Impact tests were conducted on thirty-one unembalmed human cadaver heads. Impacts were delivered to the temporo-parietal region of fixed cadavers by two, different sized, flat-rigid impactors. Yield fracture force and stiffness data for this region of the head are presented. Impactor surfaces consisted of a 5 cm2 circular plate and a 52 cm2 rectangular plate. The average stiffness value observed using the circular impactor was 1800 N/mm, with an average bone-fracture-force level of 5000 N. Skull stiffness for the rectangular impactor was 4200 N/mm, and the average fracture-force level was 12,500 N.

Recently obtained force-deflection information for the frontal, zygomatic and maxillary regions of the human cadaver head and the Hybrid III ATD head indicates need for a redesigned Anthropomorphic Test Dummy (ATD) face. A prototype, deformable, load-sensing face (DLSF) was designed, with human-like-force-deflection compliant materials. The face was divided into six load sensing segments. The force level and impact location as a function of time can be determined for each segment, as well as for a selected set of segments and the whole face. The prototype face underwent preliminary testing for comparison with available cadaver data.

Collision Safety Engineering, Inc. (CSE), has developed a test prototype system to protect occupants during lateral impacts. It is an inflatable system that offers the potential of improved protection from thoracic, abdominal and pelvic injury by moving an impact pad into the occupant early in the crash. Further, it shows promise for head and neck protection by deployment of a headbag that covers the major target areas of B-pillar, window space, and roofrail before head impact. Preliminary static and full-scale crash tests suggest the possibility of injury reduction in many real-world crashes, although much development work remains before the production viability of this concept can be established. A description of the system and its preliminary testing is preceded by an overview of side impact injury and comments on the recent NHTSA Rule Making notices dealing with side-impact injury.

Results indicate the need for a redesigned Hybrid III face capable of accurate force and acceleration measurements. New instrumentation and methods for facial fracture detection were developed, including the application of acoustic emissions. Force/ deflection information for the human cadaver head and the Hybrid III ATD were generated for the frontal, zygomatic, and maxillary regions.

Nineteen sled impact tests were conducted simulating a frontal collision exposure for an unrestrained driver. The deceleration sled buck configuration utilized the passenger compartment of a late model compact passenger vehicle, a rigid driver's seat, and a custom fabricated energy-absorbing steering column and wheel assembly. Sled impact velocities ranged from 24.1 to 42.6 km/hr. The purpose of the study was to investigate the kinematic and kinetic interaction of the driver and the energy-absorbing steering assembly and their relationship to the thoracic/abdominal injuries produced. The similarities and differences between human cadaver and anthropomorphic dummy subjects were quantified.

An economical alternative technique is presented for obtaining vehicle frontal crush characteristics from a series of repeated low speed barrier crashes. Results were analyzed using a technique of linear correlation of residual crush depth with a defined crush energy parameter. The data compared closely with crashes reported in the literature, and suggested that the structure exhibits only a slight strain rate sensitivity. Crush energy is shown to correlate well with dynamic crush depth. Relations among dynamic and residual crush and recovery distance are reported, Velocity restitution is shown to be about constant at 15% over the impact velocity range employed. A force-deflection relation based on the offset force linear harmonic oscillator theory is suggested, shown to agree quite well with data. Repeated crash testing can be an effective method to obtain information needed for development of analytical and predictive tools useful in design and reconstruction.

This paper summarizes the development of an Instrumented faceform which can record time histories of impact-related pressures at fifty-two locations over the entire face of a Hybrid 2 crash dummy skull. Pressures are measured by using piezo-electric, thin-plastic films; a high-speed, multiplex data acquisition system; signal conditioning; a software-controlled computerized data reduction and recording scheme; and a submergence calibration technique. The construction of the modified dummy face and the calibration gear are discussed. Examples of preliminary laboratory impact test results are presented. Theory and techniques relating to signal processing software, microprocessor controlled random-access-memory data-retrieval system and system calibration are also discussed. It is hoped that this tool, now undergoing final development and verification testing, will find extensive use in the evaluation and safety-related design of vehicle interiors and occupant restraints.

The CRASH3 computer program, a well known and useful tool in accident reconstruction, is shown to be innaccurate by comparison with car-to-car crash test data. Claims for accuracy of about 10 percent cannot be validated. Both the impact model and the damage only model yield results which are in error. Cases involving error well in excess of 20 percent are demonstrated. These inaccuracies are due primarily to the omission of terms in the formulation of the energy equation and to the sensitivity of the solution to the input estimate of principle-direction-of-force.

This project covers one facet of a program to develop a mechanical model for characterizing the time history of local forces on the zygomatic, maxillary and mandible regions of the human face during a frontal collision. Two mechanical devices to measure the forces on crash dummies during testing were designed, constructed and tested. The devices employed cantilever beams equipped with strain gauges. Both devices were subjected to a series of drop tests onto various materials. Time histories were compared to those obtained from cadaver experiments. While the data obtained from this testing appears to be similar to the cadaver data, further improvements and modifications will make the model much more useful.

The Simulation Model of Automobile Collisions (SMAC) computer program has seen more than a decade of use under NHTSA auspices. Although SMAC has proven itself to be a useful investigative tool, the program has several shortcomings which either have been addressed by the authors or need to be addressed by further work. This paper presents the results of our ongoing work to improve SMAC and our recommendations for further work. Those model features discussed herein which either have been or need to be revised consist of (1) the calculation of crush forces when penetration is deep (2) the representation of the vehicles' crush pressure vs deflection relationship and (3) the distribution of tire normal forces in reaction to pitch and roll. An input interfacing program called SMACED has been written and is discribed. This editing program greatly simplifies the use of SMAC and will be found particularly useful for the inexperienced or infrequent SMAC user.

Far-side lateral impacts were simulated using a Part 572 dummy and human cadavers to compare responses for several belt restraint configurations. Sled tests were conducted having a velocity change of 35 km/hr at a 10 g deceleration level. It was estimated from field data that a 35 km/hr velocity change of the laterally struck vehicle represents about an 80th percentile level for injury-producing lateral collisions. Subjects restrained by a three-point belt system with an outboard anchored diagonal shoulder belt (i.e., positioned over the shoulder opposite the side of impact) rotated out of the shoulder belt and onto the seat. The subject received some lateral restraint due to interaction with the shoulder belt and seatback. The subjects restrained by a three-point belt system with an inboard anchored diagonal shoulder belt (i.e., positioned over the shoulder on the side of impact) remained essentially upright due to shoulder belt interaction with the neck and/or head.

Classical blunt thoracic impacts have involved midsternal anteroposterior loadings to an upright-positioned subject. Data on the sensitivity of human cadaver and/or animal model biomechanical and injury responses to blunt loadings at different sternal locations is needed to evaluate the efficacy of current injury-potential guidelines for nonsite-specific frontal impacts. In addition, the biomechanics and injury mechanisms associated with lateral impacts constitute a subject of increasing consideration for occupant protection. Twelve anesthetized pigs were subjected to various blunt frontal or a right-side impact to assess biomechanical and injury response differences in a living animal model.

Thoracic impact response and injuries of living and postmortem porcine siblings were investigated to quantify comparative differences. Thirteen male animals, averaging 61.4 kg, from five different porcine litters comprised the two animal samples. Porcine brothers were subjected to similar impact exposures for which at least one brother was tested live, anesthetized and another dead, post rigor with vascular repressurization. Statistically significant differences in biomechanical responses and injuries were observed between live and postmortem siblings. On the average the anesthetized live animals demonstrated a greater thoracic compliance, as measured by increased normalized total deflections (21% Hi), and reduced overall injuries (AIS 14% Lo and rib fractures 26% Lo) at lower peak force levels (13% Lo) than did the postmortem subjects. However, individual comparisons of “match-tested” siblings demonstrated very similar responses in some cases.

The purpose of this paper is to present a comparison of whole body, target impingement knee impact response for a Part 572 dummy versus that for anthropometrically similar embalmed human cadavers. “Response” is defined here to include the impact force-time history as sensed by 1) femur load cells, and 2) impingement target load cells for the dummy and by the target load cells for the cadavers. The data presented demonstrate significantly higher peak forces and correspondingly shorter pulse durations for the dummy than for the companion cadaver subjects under similar test conditions and at all velocity levels investigated. For the dummy, the ratio of forces measured by the femur load cells to those measured by the impingement target load cells averaged eight tenths.