Refine Your Search

Topic

Search Results

Standard

Groove Design - Metal Face Seal

2019-06-06
CURRENT
AIR1108A
Groove designs presented herein are applicable for use with machined or formed metal seals which are similar in configuration to those shown in figure 3, which operate under internal pressure or in vacuum service and which have been specifically qualified or recommended by the purchaser or the manufacturer for use with this AIR. They are also applicable for use with metal o-rings (e.g., MS9142, MS202 thru MS9205) where interchangeability with machined or formed metal seals is desired. For metal o-ring groove designs where inter-changeability is not a requirement refer to ARP 674.
Standard

Inserts, Screw Thread, Helical Coil 19Cr-9.2Ni, Corrosion Resistant Steel, Procurement Specification for

2019-02-13
CURRENT
AS7245B
This specification covers closely-wound helical coil, screw thread inserts made of a corrosion resistant steel formed wire with a chemical composition in accordance with Table 1 and identified under the Unified Numbering System as UNS S30200 or UNS S30400 that can be formed by an insert manufacturer to achieve the requirements of this procurement specification. The inner surface of the insert coil, after assembly into a screw thread tapped hole, provides internal threads of standard 60° Unified form.
Standard

Bolts, Cobalt-Chromium-Nickel Alloy, Uns R30035, Tensile Strength 260 Ksi, Procurement Specification

2018-12-07
WIP
AS7468C
This procurement specification covers bolts made from a corrosion resistant, work-strengthened, cobalt-chromium-nickel alloy of the type identified under the Unified Numbering System as UNS R30035. The following specification designations and their properties are covered: AS7468 260 ksi minimum ultimate tensile strength at room temperature, 135 ksi tension to 13.5 ksi tension fatigue at room temperature; and AS7468-1 260 ksi minimum ultimate tensile strength at room temperature, 145 ksi minimum ultimate shear strength at room temperature.
Standard

Spacers and Washers, Procurement Specification for, Metric

2018-10-16
CURRENT
MA1784A
This specification covers metric aircraft quality spacers for use as positioners for tubes, flat washers for use as load spreaders, galling protection of adjacent surfaces and or material compatibility, and key or tab washers for use as locks for bolts, nuts, and screws.
Standard

Limits, Table of Limits and Lubrication Charts

2018-09-11
CURRENT
AS176D
This specification covers the requirements for the preparation of Limits, Table of Limits and Lubrication Charts in published form for service and production use.
Standard

Rings, Retaining – Spiral Wound, Uniform Section Corrosion and Heat Resistant, UNS S66286

2018-07-02
CURRENT
AS4299B
This procurement specification covers retaining rings of the spiral wound type with uniform rectangular cross-section, made of a corrosion and heat resistant age hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286, work strengthened and heat treated to a tensile strength of 185 to 240 ksi at room temperature.
Standard

Nut, Self Locking - UNS S66286, 425°C & 650°C, 1100 MPa, MJ Thread, Procurement Specification For, Metric

2018-03-30
CURRENT
MA1568A
This specification establishes the requirements for the following types of self locking nuts: a Wrenching nuts: i.e., hex, double hex, spline drive. b Anchor nuts: i.e., plate nuts, gang channel nuts, shank (clinch) nuts. The wrenching nuts, shank nuts, and nut elements of plate and gang channel nuts are made of corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286.
Standard

Torque Tightening Threaded Fasteners

2018-03-04
CURRENT
AIR1471B
The purpose of this SAE Aerospace Information Report (AIR) is to provide the aerospace propulsion industry with recommended assembly torque limits for commonly used aircraft propulsion system threaded fasteners when a common torque value per size is the objective.
X