Refine Your Search

Search Results

Standard

Battery Booster Cables

2012-03-15
CURRENT
J1494_201203
The purpose of this SAE Recommended Practice is to establish minimum performance and user information requirements for battery booster cable sets used with 6 OR 12-VOLT BATTERIES. Such sets may be used to provide a temporary connection of a surface vehicle battery to another similar battery to provide emergency power when required. This document DOES NOT ENDORSE NOR RECOMMEND the potentially hazardous procedure of jump-starting a vehicle.
Standard

High Voltage Automotive Wiring Assembly Design

2012-03-15
CURRENT
J1673_201203
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnesses to road vehicles. This document applies to any wiring system which contains one or more circuits operating between 50 V DC or AC RMS and 600 V DC or AC RMS excluding automotive ignition cable.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses Part 1: Single-Pole Connectors Flat Blade Terminals Dimensional Characteristics and Specific Requirements

2003-10-28
HISTORICAL
J2223/1_200310
This SAE Standard specifies dimensional characteristics of flat blades of single-pole connectors and specific requirements for on-board electrical harnesses of road vehicles, which can be fitted into female connectors such as those given as in Appendix A. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses Part 3: Multipole Connectors Flat Blade Terminals Dimensional Characteristics and Specific Requirements

2003-10-28
HISTORICAL
J2223/3_200310
This SAE Standard defines dimensional characteristics of existing flat blades of multipole connectors and specific requirements for on-board electrical harnesses of road vehicles. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
Standard

Low Tension Wiring and Cable Terminals and Splice Clips

2001-12-28
HISTORICAL
J163_200112
The SAE Recommended Practice covers the application requirements for terminals and splice clips attached to stranded low tension wiring and cable as shown in SAE J878 and SAE J558. In addition, it covers maximum voltage drop limits for friction type connections.
Standard

Battery Booster Cables

2001-12-27
HISTORICAL
J1494_200112
The purpose of this SAE Recommended Practice is to establish minimum performance and user information requirements for battery booster cable sets used with 6 OR 12-VOLT BATTERIES. Such sets may be used to provide a temporary connection of a surface vehicle battery to another similar battery to provide emergency power when required. This document DOES NOT ENDORSE NOR RECOMMEND the potentially hazardous procedure of jump-starting a vehicle.
Standard

Five Conductor Electrical Connectors for Automotive Type Trailers

1999-01-26
CURRENT
J895_199901
This SAE Recommended Practice covers the wiring and connector standards for nonpassenger carrying trailers, SAE Classes 1-3, with circuit loads not to exceed 7.5 amp per circuit. It provides the lighting circuits of these trailers with a universal connecting device, standard circuit coding and protection for the wiring from hazards and shorts. Cancelled-All information now contained in J1239
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 1: Single-Pole Connectors - Flat Blade Terminals - Dimensional Characteristics and Specific Requirements

1998-12-01
HISTORICAL
J2223/1_199812
This SAE Standard specifies dimensional characteristics of flat blades of single-pole connectors and specific requirements for on-board electrical harnesses of road vehicles, which can be fitted into female connectors such as those given as in Appendix A. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 3: Multipole Connectors - Flat Blade Terminals - Dimensional Characteristics and Specific Requirements

1998-12-01
HISTORICAL
J2223/3_199812
This SAE Standard defines dimensional characteristics of existing flat blades of multipole connectors and specific requirements for on-board electrical harnesses of road vehicles. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
Standard

Connections for High Voltage On-Board Road Vehicle Electrical Wiring Harnesses-Test Methods and General Performance Requirements

1998-03-01
HISTORICAL
J1742_199803
This SAE REcommended practice defines recommended test methods and general performance requirements of single-pole and multi-pole connectors for on-board electrical wiring harnesses of electric or hybrid powered road vehicles operating at voltages between 50 and 600 V AC or DC rms and those circuits using copper wire only. these requireemnts are not intended for connections internal to electrical/electronic modules or complete subassemblies. this document applies to connectors designed to be disconnected in the case of repair and/or maintenance after mounting in the vehicle. This document excludes onoe-part connections, i.e., where one part of the connection has direct contact to the pattern of the circuit board. Duty cycles are considered to be application specific and are not specified in this document; however, these effects must be considered during design. The Recommended Practice for Highvoltage Wiring Assembly is contained in SAE j1673.
Standard

High Voltage Automotive Wiring Assembly Design

1996-07-01
HISTORICAL
J1673_199607
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnesses to road vehicles. This document applies to any wiring system which contains one or more circuits operating between 50 V DC or AC RMS and 600 V DC or AC RMS excluding automotive ignition cable.
Standard

Four-, Five-, and Eight-Conductor Electrical Connectors for Automotive Type Trailers

1995-10-01
HISTORICAL
J1239_199510
This SAE Recommended Practice covers the wiring and rectangularly shaped connector standards for all types of trailers whose gross weight does not exceed 4540 kg (10 000 lb). These trailers are grouped in SAE J684, with running light circuit loads not to exceed 7.5 amps per circuit. This document provides circuits for lighting, electric brakes, trailer battery charging, and an auxiliary circuit color coding and protection for the wiring from hazards or short circuits. Color coding is compatible with SAE J560 and ISO 1724-1980(E).
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses--Part 1: Single-Pole Connectors--Flat Bladeterminals--Dimensional Characteristics and Specific Requirements

1994-02-01
HISTORICAL
J2223/1_199402
This SAE Draft Technical Report specifies dimensional characteristics of flat blades of single-pole connectors and specific requirements for on-board electrical harnesses of road vehicles, which can be fitted into female connectors such as those given as in Appendix A. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses--Part 3: Multipole Connectors--Flat Blade Terminals--Dimensional Characteristics and Specific Requirements

1994-02-01
HISTORICAL
J2223/3_199402
This SAE Draft Technical Report defines dimensional characteristics of existing flat blades of multipole connectors and specific requirements for on-board electrical harnesses of road vehicles. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
Standard

Battery Booster Cables

1989-06-01
HISTORICAL
J1494_198906
The purpose of this SAE Recommended Practice is to establish minimum performance and user information requirements for battery booster cable sets. Such sets may be used to provide a temporary connection of a surface vehicle battery to another similar battery to provide emergency power when required. This recommended practice DOES NOT ENDORSE NOR RECOMMEND the potentially hazardous procedure of jump starting a vehicle.
X