Refine Your Search

Date

Date

Chemicals Fasteners Committee Metals

Search Results

Viewing 1 to 20 of 32
12Next >Last >>
Sort by published
Standard

Steel Self-Drilling Tapping Screws
2022-04-14
WIP
J78
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications having point Styles 2, 3, 4, and 5. It is the objective of this document to ensure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly.
Standard

Steel Self-Drilling Tapping Screws
2021-07-28
CURRENT
J78_202107
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications having point Styles 2, 3, 4, and 5. It is the objective of this document to ensure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners
2019-11-12
WIP
J429
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Protective Coatings for Fasteners
2019-10-07
CURRENT
J1648_201910
This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series
2017-01-03
CURRENT
J174M_201701
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners
2014-05-07
CURRENT
J429_201405
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners
2013-04-29
HISTORICAL
J429_201304
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Protective Coatings for Fasteners
2013-04-15
HISTORICAL
J1648_201304
This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.
Standard

Blind Rivets - Break Mandrel Type
2013-04-15
HISTORICAL
J1200_201304
This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.
Standard

Mechanical and Material Requirements for Metric Wheel Bolts
2013-04-11
HISTORICAL
J1102M_201304
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Wheel Bolts
2013-04-11
HISTORICAL
J1102_201304
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Dryseal Pipe Threads
2013-02-01
CURRENT
J476_201302
The Dryseal American Standard Taper Pipe Thread, the Dryseal American Fuel Internal Straight Pipe Thread and the Dryseal American Intermediate Internal Straight Pipe Thread covered by this standard conform with the American Standard ASA-B2.2. The Dryseal SAE-Short Taper Pipe Thread in this standard conforms with the Dryseal American Standard Taper Pipe Thread except for the length of thread, which is shortened for increased clearance and economy of material. The significant feature of the Dryseal thread is controlled truncation at the crest and root to assure metal to metal contact coincident with or prior to flank contact. Contact at the crest and root prevents spiral leakage and insures pressure-tight joints without the use of a lubricant or sealer. Lubricants, if not functionally objectionable, may be used to minimize the possibility of galling in assembly.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners
2011-09-08
HISTORICAL
J429_201109
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 used in automotive and related industries in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.
Standard

Mechanical and Material Requirements for Metric Wheel Bolts
2001-03-12
HISTORICAL
J1102M_200103
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners
1999-01-01
HISTORICAL
J429_199901
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, sems1, and U-bolts2 used in automotive and related industries in sizes to 1-1/2 in inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.
Standard

Blind Rivets—Break Mandrel Type
1998-05-01
HISTORICAL
J1200_199805
This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners
1998-05-01
HISTORICAL
J429_199805
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, sems1, and U-bolts2 used in automotive and related industries in sizes to 1-1/2 in inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.
Standard

MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
1997-07-01
HISTORICAL
J429_199707
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, sems1, and U-bolts2 used in automotive and related industries in sizes to 1-1/2 in inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.
12Next >Last >>
X