Refine Your Search

Topic

Search Results

Standard

Deliverable Aerospace Software Supplement for AS9100A, Quality Management Systems - Aerospace - Requirements for Software (based on AS9100A)

2019-08-28
WIP
AS9006B
The basic requirements of AS9100A apply with the following clarifications. This document supplements the requirements of AS9100A for deliverable software. This supplement contains Quality System requirements for suppliers of products that contain deliverable embedded or loadable airborne, spaceborne or ground support software components that are part of an aircraft Type Design, weapon system, missile or spacecraft operational software and/or support software that is used in the development and maintenance of deliverable software. This includes the host operating system software including assemblers, compilers, linkers, loaders, editors, code generators, analyzers, ground simulators and trainers, flight test data reduction, etc., that directly support creation, test and maintenance of the deliverable software.
Standard

Aerospace First Article Inspection Requirement

2019-08-21
WIP
AS9102C
This standard establishes the baseline requirements for performing and documenting FAI. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the applicable statutory or regulatory requirements shall take precedence.
Standard

Aerospace Series - Notice of Change (NOC) Requirements

2019-04-05
WIP
AS9116A
The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design activity controls various aspects of the configuration and specifications related to the product. When a change to design information is requested or required, the change has to be evaluated against the impacts to the higher-level system. Proposed changes to design information that the design activity identifies to be minor and have no effect on their product requirements or specifications have the potential to be concurrently implemented and approved, where authorized to do so. Changes that affect customer mandated requirements or specifications shall be approved prior to implementation.
Standard

Aerospace Guidance for Non-Deliverable Software

2019-03-05
WIP
ARP9005B
General: This document contains recommended practices for the effective control of non-deliverable software. It addresses practices for control during the development, production, release maintenance, and retirement of non-deliverable software, as well as for software procured from outside manufacturers and incorporated in the production, evaluation, test, acceptance or calibration of processes. For the purposes of this document, the terms software and non-deliverable software are considered synonymous. Application: The guidelines in this ARP apply to non-deliverable software that: - directly relates to design, manufacture, inspection, test or calibration of a deliverable product, and - directly affects the configuration, conformity or quality of a deliverable product.
Standard

Statistical Product Acceptance Requirements Using Process Control Methods

2018-06-02
CURRENT
ARP9013/3A
ARP9013/3 recommended practice specifies a product acceptance system using process control methods. Its purpose is to assure conformance for specified characteristics. Use of process control techniques for product acceptance requires maintaining process stability and capability. A stable and capable process is the best assurance of conforming hardware for the customer. There can be lower inspection costs associated with a process control acceptance approach.
Standard

Statistical Product Acceptance Requirements Using Isolated Lot Sampling Methods

2018-06-02
CURRENT
ARP9013/1A
The purpose of this SAE Aerospace Recommended Practice (ARP) is to ensure conformance for each product characteristic being verified in a lot, without maintaining information from previous lots. ARP9013/1 specifies a product acceptance system for isolated lots. For example, isolated lot sampling avoids keeping track of the normal, tightened, and reduced levels of sampling formerly used in MIL-STD-105 and currently used in ANSI/ASQC Z1.4. Because those switching rules provided significant long-term protection for product quality, these isolated lot tables replace that protection in other ways.
Standard

Statistical Product Acceptance Requirements

2018-06-02
CURRENT
ARP9013A
This SAE Aerospace Recommended Practice (ARP) establishes the general requirements when implementing any of the statistical product acceptance methods as defined in ARP9013/1, ARP9013/2, ARP9013/3, and ARP9013/4. This recommended practice also establishes the minimum content required to be covered in an organization's documented procedures that govern their application of statistical product acceptance methods. These general requirements and documented procedures apply the requirements of AS9100 plus requirements for retrievability, safety/critical characteristics, quality parameters, and that these parameters protect the customer. This recommended practice is to be used in conjunction with the variety of sampling strategies, statistical techniques, and process control methods of the ARP9013/1 through ARP9013/4 recommended practices as chosen by the organization.
Standard

Aerospace Series - Quality Management Systems Statistical Product Acceptance Requirements

2018-01-20
CURRENT
AS9138
This standard establishes requirements when implementing statistical product acceptance methods to meet defined risk requirements. This standard also establishes the minimum content required to be covered in an organization’s documented procedures that govern their application of statistical product acceptance methods. These general requirements and documented procedures apply the requirements of the 9100/9110/9120 quality management system standards, in addition to establishing requirements for retrievability, safety/critical characteristics, and quality parameters that protect the customer.
Standard

Quality Management Systems - Requirements for Aviation, Space, and Defense Organizations - Deliverable Software (Supplement to 9100:2016)

2017-02-01
CURRENT
AS9115A
The requirements of 9100 apply with the following clarification for software. This standard supplements the 9100 standard requirements for deliverable software and contains quality management system requirements for organizations that design, develop, and/or produce deliverable software and services for the aviation, space, and defense industry. This includes, as required, support software that is used in the development and maintenance of deliverable software and services. The deliverable software may be stand-alone, embedded, mobile application, or loadable into a target computer. This deliverable software may also be part of services (e.g., cloud environment, web hosted solutions or platforms).
Standard

Aerospace Series – Requirements for Advanced Product Quality Planning and Production Part Approval Process

2016-11-08
CURRENT
AS9145
This standard establishes requirements for performing and documenting APQP and PPAP. APQP begins with conceptual product needs and extends through product definition, production planning, product and process validation (i.e., PPAP), product use, and post-delivery service. This standard integrates and collaborates with the requirements of the 9100, 9102, 9103, and 9110 standards. The requirements specified in this standard are complementary (not alternative) to contractual and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.
Standard

Aerospace Series - Root Cause Analysis and Problem Solving (9S Methodology)

2016-11-08
CURRENT
ARP9136
The objective of any organization, as part of continual improvement, is to reduce the number of issues (i.e., undesirable conditions, defects, failures) and to minimize their impact on quality, delivery performance, and cost. This includes having processes in place to detect and eradicate significant and recurrent issues, which implies having well identified problems, a common understanding of their impact and associated root causes, and having defined and implemented adequate actions so that these problems, including similar issues will not happen again.
Standard

Quality Management Systems - Requirements for Aviation, Space, and Defense Organizations

2016-09-20
CURRENT
AS9100D
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence.
Standard

Aerospace Guidance for Non-Deliverable Software

2016-06-27
CURRENT
ARP9005A
This document contains recommended practices for the effective control of non-deliverable software. It addresses practices for control during the development, production, release maintenance, and retirement of non-deliverable software, as well as for software procured from outside manufacturers and incorporated in the production, evaluation, test, acceptance or calibration of processes. For the purposes of this document, the terms software and non-deliverable software are considered synonymous.
Standard

Data Matrix Quality Requirements for Parts Marking

2015-05-19
CURRENT
AS9132B
This standard defines uniform quality and technical requirements relative to metallic parts marking performed using "data matrix symbology" within the aviation, space, and defense industry. ISO/IEC 16022 specifies general requirements (e.g., data character encodation, error correction rules, decoding algorithm). In addition to ISO/IEC 16022 specification, part identification with such symbology is subject to the requirements in this standard to ensure electronic reading of the symbol. The marking processes covered by this standard are as follows: Dot Peening Laser Electro-Chemical Etching Further marking processes will be included, if required. Unless specified otherwise in the contractual business relationship, the company responsible for the design of the part shall determine the location of the data matrix marking. Symbol position should allow optimum illumination from all sides for readability. This standard does not specify information to be encoded.
Standard

A Process Standard for the Storage, Retrieval and Use of Three-Dimensional Type Design Data

2015-04-21
CURRENT
ARP9034A
This document describes requirements for standardized processes (and associated technologies) that ensure type design data are retrievable and usable for the life of a type certificate (50+ years). These processes are primarily concerned with, but not limited to, digital type design data retained in three-dimensional representations and associated data that is required for complete product definition, such as tolerances, specification call-outs, product structure and configuration control data, etc. This process standard includes process requirements for managing the evolution of technologies required to ensure the availability of the data for the life of the product. This data must be available to meet regulatory, legal, contractual and business requirements. This process standard is not intended to incorporate every company specific requirement and does not dictate specific organizational structures within a company.
Standard

Aerospace Series – Notice of Change (NOC) Requirements

2015-03-12
CURRENT
AS9016A
The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design activity controls various aspects of the configuration and specifications related to the product. When a change to design information is requested or required, the change has to be evaluated against the impacts to the higher-level system. Proposed changes to design information that the design activity identifies to be minor and have no effect on their product requirements or specifications have the potential to be concurrently implemented and approved, where authorized to do so. Changes that affect customer mandated requirements or specifications must be approved prior to implementation.
Standard

Aerospace Series - Notice of Change (NOC) Requirements

2014-10-30
CURRENT
AS9116
The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design activity controls various aspects of the configuration and specifications related to the product. When a change to design information is requested or required, the change has to be evaluated against the impacts to the higher-level system. Proposed changes to design information that the design activity identifies to be minor and have no effect on their product requirements or specifications have the potential to be concurrently implemented and approved, where authorized to do so. Changes that affect customer mandated requirements or specifications shall be approved prior to implementation.
Standard

Aerospace First Article Inspection Requirement

2014-10-06
CURRENT
AS9102B
This standard establishes the baseline requirements for performing and documenting FAI. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the applicable statutory or regulatory requirements shall take precedence.
X