Search Results

For simulation and analysis of vehicles there is a need to have a means of generating drive cycles which have properties similar to real world driving. A method is presented which uses measured vehicle speed from a number of vehicles to generate a Markov chain model. This Markov chain model is capable of generating drive cycles which match the statistics of the original data set. This Markov model is then used in an iterative fashion to generate drive cycles which match constraints imposed by the user. These constraints could include factors such number of stops, total distance, average speed, or maximum speed. In this paper, systematic analysis was done for a PHEV fleet which consists of 9 PHEVs that were instrumented using data loggers for a period of approximately two years. Statistical analysis using principal component analysis and a clustering approach was carried out for the real world velocity profiles.

Homogeneous Charge Compression Ignition (HCCI) is considered a very promising concept to achieve low NOx and Particulate Matter emissions in traditional spark ignition and Diesel engines. However, controlling the complex mechanisms which govern the combustion process and finding a proper method for the fuel introduction for Diesel HCCI engines have proven to still be a challenge. In addition, the well known IMEP limitations of HCCI combustion restrict the benefits on emissions to low engine load conditions. The current work attempts to extend the benefits of HCCI combustion to a broader range of engine operating conditions by blending the conventional Direct Injection (DI) with the external fuel atomization. A dual combustion system could potentially overcome the limits of low-load operations and allow for a gradual transition between the conventional DI mode at high load and the HCCI external mixture formation at idle and low load.

An appropriate fault diagnosis and Isolation (FDI) strategy is very useful to prevent system failure. In this paper, a model-based fault diagnosis strategy is developed for an internal combustion engine (ICE) under speed control. Engine throttle fault and the manifold pressure sensor fault are detected and isolated. A nonlinear observer based residual generation approach is proposed. Manifold pressure and throttle are observed. Fault codes are designed with redundancy to prevent bit error. Performance of fault diagnosis strategy has been evaluated with simulations.

Research has been conducted to develop a methodology for the generation of driving and duty cycles for refuse vehicles in conjunction with a larger effort in the design of a hybrid-electric refuse vehicle. This methodology includes the definition of real-world data that was collected, as well as a data analysis procedure based on sequencing of the collected data into micro-trips and hydraulic cycles. The methodology then applies multi-variate statistical analysis techniques to the sequences for classification. Finally, driving and duty cycles are generated based on matching the statistical metrics and distributions of the generated cycles to the collected database. Simulated vehicle fuel economy for these cycles is also compared to measured values.

In this paper, the detection and isolation of actuator faults (both measured and commanded) occurring in the engine breathing and the fueling systems of a spark-ignition direct-injection (SIDI) engine are described. The breathing system in an SIDI engine usually consists of a fresh air induction path via an electronically controlled throttle (ECT) and an exhaust gas recirculation (EGR) path via an EGR valve. They are dynamically coupled through the intake manifold to form a gas mixture, which eventually enters the engine cylinders for a subsequent combustion process. Meanwhile, the fueling system is equipped with a high-pressure common-rail injection for a precise control of the fuel quantity directly injected into the engine cylinders. Since the coupled system is highly nonlinear in nature, the fault diagnosis will be performed by generating residuals based on multiple nonlinear observers.

The stochastic Fault Detection and Isolation (FDI) algorithm, known as the statistical local approach, is applied in a model-based framework to the diagnosis of component faults in the air-intake system of an automotive engine. The FDI scheme is first presented as a general methodology that permits the detection of faults in complex nonlinear systems without the need for building inverse models or numerous observers. Although sensor and actuator faults can be detected by this FDI methodology, component faults are generally more difficult to diagnose. Hence, this paper focuses on the detection and isolation of component faults for which the local approach is especially suitable. The challenge is to provide robust on-board diagnostics regardless of the inherent nonlinearities in a system and the random noise present.

This year, in the third year of FutureTruck competition, the Ohio State University team has taken the challenge to convert a 2002 Ford Explorer into a more fuel efficient and environmentally friendly SUV. This goal was achieved by use of a post-transmission, charge sustaining, parallel hybrid diesel-electric drivetrain. The main power source is a 2.5-liter, 103 kW advanced CIDI engine manufactured by VM Motori. A 55 kW Ecostar AC induction electric motor provides the supplemental power. The powertrain is managed by a state of the art supervisory control system which optimizes powertrain characteristics using advanced energy management and emission control algorithms. A unique driver interface implementing advanced telematics, and an interior designed specifically to reduce weight and be more environmentally friendly add to the utility of the vehicle as well as the consumer appeal.

In recent years, the increasing interest and requirements for improved engine diagnostics and control has led to the implementation of several different sensing and signal processing technologies. In order to optimize the performance and emission of an engine, detailed and specified knowledge of the combustion process inside the engine cylinder is required. In that sense, the torque generated by each combustion event in an IC engine is one of the most important variables related to the combustion process and engine performance. This paper introduces torque estimation techniques in the real-time basis for engine control applications using the measurement of crankshaft speed variation. The torque estimation scheme presented in this paper consists of two entirely different approaches, “Stochastic Analysis” and “Frequency Analysis”.

Currently Hybrid Electric Vehicles (HEV) are being considered as an alternative to conventional automobiles in order to improve efficiency and reduce emissions. A major concern of these vehicles is how to effectively operate the electric machine and the ICE. Towards this end two operation strategies, an best efficiency and a least fuel use strategy, are presented in this paper. To demonstrate the potential of an advanced operation strategy for HEV's, a fuzzy logic controller has been developed and implemented in simulation in the National Renewable Energy Laboratory's simulator Advisor (version 2.0.2). Results have also been gathered from chassis dynamometer tests in order to verify the effectiveness of Advisor. The Fuzzy Logic Controller (FLC) utilizes the electric motor in a parallel hybrid electric vehicle (HEV) to force the ICE (66KW Volkswagen TDI) to operate at or near its peak point of efficiency or at or near its best fuel economy.

This paper presents the development of a model-based air/fuel ratio controller for a high performance engine that uses, in addition to other usual signals, the throttle angle to enable predictive air mass flow rate estimation. The objective of the paper is to evaluate the possibility to achieve a finer air/fuel ratio control during transients that involve sudden variations in the physical conditions inside the intake manifold, due, for example, to fast throttle opening or closing actions. The air mass flow rate toward the engine cylinders undertakes strong variation in such transients, and its correct estimation becomes critical mainly because of the time lag between its evaluation and the instant when the air actually enters the cylinders.

Carbon canisters have been adapted for automobile use since the early 1970s to control evaporative emissions. Stringent emission regulations and the requirement for an enhanced evaporative emissions test procedure, make this an important issue. The air and evaporative fuel from the carbon canister therefore need important consideration with respect to air to fuel ratio (AFR) control and idle by-pass air control. Although a few complex models of the activated carbon canister have been developed, a control-oriented, simplistic carbon canister model needs to be developed. This paper explores the control-oriented modeling of a canister purge air system along with the on-line estimation of evaporative fuel loading of the activated carbon. An attempt was made at providing an analytical expression for the evaporative fuel and air entering the intake manifold.

Due to the stringent emission regulations, On-Board Diagnostics II (OBD II) and the requirement of enhanced evaporative emissions test procedure, an aggressive canister purge control strategy is required for automotive vehicles. The enhanced evaporative emissions test procedure has forced car manufacturer to purge the carbon canister in the vehicle idle condition so that production vehicles meet the SHED and hot soak test requirements. This not only worsens the idle speed quality but also tends to increase exhaust emission levels. Using analytical models of evaporative air and fuel, feed-forward control strategy for both idle by-pass air and air to fuel ratio can be improved. This paper demonstrates an application of evaporative system modeling to the idle air and air to fuel ratio control.

Electronic Throttle Control systems substitute the driver in commanding throttle position, with the driver acting on a potentiometer connected to the accelerator pedal. Such strategies allow precise control of air-fuel ratio and of other parameters, e.g. engine efficiency or vehicle driveability, but require detailed information about the engine operating conditions, in order to be implemented inside the Electronic Control Unit (ECU). In order to determine throttle position, an interpretation of the driver desire (revealed by the accelerator pedal position) is performed by the ECU. In our approach, such interpretation is carried out in terms of a torque request that can be appropriately addressed knowing the actual engine-vehicle operating conditions, which depend on the acting torques. Estimates of the torque due to in-cylinder pressure (indicated torque), as well as the torque required by the vehicle (load torque), must then be available to the control module.

Electronic throttle control is increasingly being considered as a viable alternative to conventional air management systems in modern spark-ignition engines. In such a scheme, driver throttle commands are interpreted by the powertrain control module together with many other inputs; rather than directly commanding throttle position, the driver is now simply requesting torque - a request that needs to be appropriately interpreted by the control module. Engine management under these conditions will require optimal control of the engine torque required by the various vehicle subsystems, ranging from HVAC, to electrical and hydraulic accessories, to the vehicle itself. In this context, the real-time estimation of engine and load torque can play a very important role, especially if this estimation can be performed using the same signals already available to the powertrain control module.

Fault diagnosis for automotive systems is driven by government regulations, vehicle repairability, and customer satisfaction. Several methods have been developed to detect and isolate faults in automotive systems, subsystems and components with special emphasis on those faults that affect the exhaust gas emission levels. Limit checks, model-based, and knowledge-based methods are applied for diagnosing malfunctions in emission control systems. Incipient and partial faults may be hard to detect when using a detection scheme that implements any of the previously mentioned methods individually; the integration of model-based and knowledge-based diagnostic methods may provide a more robust approach. In the present paper, use is made of fuzzy residual evaluation and of a fuzzy expert system to improve the performance of a fault detection method based on a mathematical model of the engine.

The use of mathematical models derived from physical principles is gaining more widespread acceptance for automotive control and diagnostic applications. A suitable mathematical model may reduce, though not eliminate, the need for empirical calibrations, and may help in accommodating changes in operating conditions, external disturbances, vehicle to vehicle variability, aging etc. Recent studies have shown that model based approaches for both control and diagnostic design offer a viable alternative to empirical methods for industrial applications. However, until recently, model-based control and diagnostic algorithms have been designed separately, without considering their interactions explicitly. As a consequence, the performance of these algorithms may be limited, and even deteriorated in the presence of modeling uncertainty and disturbance.

Over the years numerous researchers have suggested that the ionization current signal carries within it combustion relevant information. The possibility of using this signal for diagnostics and control provides motivation for continued research in this area. To be able to use the ion current signal for feedback control a reliable estimate of some combustion related parameter is necessary and therein lies the difficulty. Given the nature of the ion current signal this is not a trivial task. Fei An et al. [1] employed PCA for feature extraction and then used these feature vectors to design a neural network based classifier for the estimation of air to fuel ratio (AFR). Although the classifier predicted AFR with sufficient reliability, a major draw back was that the ion current signals used for prediction were averaged signals thus precluding a cycle to cycle estimate of AFR.

This paper discusses the use of intelligent control techniques for the control of a parallel hybrid electric vehicle powertrain. Artificial neural networks and fuzzy logic are used to implement a load leveling strategy. The resulting vehicle control unit, a supervisory controller, coordinates the powertrain components. The presented controller has the ability to adapt to different drivers and driving cycles. This allows a control strategy which includes both fuel-economy and performance modes. The strategy was implemented on the Ohio State University FutureCar.

The process of incorporating the spark plug as a combustion probe, to perform misfire and knock detection, air to fuel ratio and spark timing control has been the subject of research for some time now. [3], [4]. The feasibility of the approach however depends on being able to correlate some characteristic of the ion current signal to the in cylinder combustion process. Shimaski et al. [3] and Miyata et al. [4] suggest such a relationship. The objective of this research has been to extract combustion information from the measured ion current flowing between spark plug electrodes by using various advanced signal processing methods, and to develop a methodology that will permit combustion diagnostics and possibly control based on these measurements. Tests were carried out on a single-cylinder, methane-fueled CFR engine.

The evolution of the diagnostic equipment for automotive application is the direct effect of the implementation of sophisticated and high technology control systems in the new generation of passenger cars. One of the most challenging issues in automotive diagnostics is the ability to assess, to analyze, and to integrate all the information and data supplied by the vehicle's on-board computer. The data available might be in the form of fault codes or sensors and actuators voltages. Moreover, as environmental regulations get more stringent, knowledge of the concentration of different species emitted from the tailpipe during the inspection and maintenance programs can become of great importance for an integrated powertrain diagnostic system. A knowledge-based diagnostic tool is one of the approaches that can be adopted to carry out the challenging task of detecting and diagnosing faults related to the emissions control system in an automobile.