Search Results

This paper presents the evaluation results from the analysis of different blends of fuels using the 13-mode standard SAE testing method. Six high oleic safflower oil blends, six ester blends, six high oleic sunflower oil blends, and six sunflower oil blends were used in this portion of the investigation. Additionally, the results from the repeated 13-mode tests for all the 25/75% mixtures with a complete diesel fuel test before and after each alternative fuel are presented.

The paper* describes the analysis of experimental results of a laboratory flow apparatus used to measure the energy released during premixed combustion at atmospheric pressure in near quiescent air. The flow apparatus, described in a parallel paper, has the means to provide air temperatures in the range between 800 and 950° K. An infrared radiation detector and a photodiode sensitive to radiation in the visible range of the electromagnetic spectrum monitor the events taking place inside the combustion chamber through a sapphire lens. A beam splitter permits simultaneous observation of the combustion events by both sensors. The difference in response times between the two sensors offers information about the non-luminous premixed combustion. Four fuels, No. 2-D diesel fuel, a 50/50% volumetric mixture of diesel fuel and sunflower oil, neat sunflower oil, and neat high oleic safflower oil were used.

The paper describes engine modifications, which are proposed to provide a means to overcome the adverse effect of sunflower oil fuel on diesel engines' longevity. The proposed system consists of a dual fuel system and fuel preheater. The dual fuel system was designed to eliminate engine conditions that are responsible for the majority of the problems associated with the use of sunflower oil fuel. Specifically, the dual fuel system will (1) prevent the operation of an engine on alternative fuels at low-load, low-speed conditions, (2) reduce the exposure time of the fuel injection system to the sunflower oil at the excessively high temperature conditions during the transition process from high to light loads, (3) eliminate the conditions (such as cold start-up) at which the fuel temperature is too low for acceptable atomization, and (4) eliminate the exposure of the fuel injection system to sunflower oil during the shut-down period.

A neat, alkali-refined sunflower oil, a 50/50 blend (v/v) of sunflower oil and #2 diesel fuel, and 100% #2 diesel fuel were evaluated in a direct injected, one-cylinder Petter engine according to the SAE 13 mode test procedure. The experiment was conducted to evaluate the effects of plant oil based alternative fuels on exhaust emissions and to simultaneously compare the test fuels. Additionally, the effect of engine load and speed on the exhaust emissions using the plant oil alternative fuels was statistically evaluated. The response variables were CO, NO, HC, and smoke. The predictor variables were the concentration of sunflower oil in the test fuel, the engine speed, and load. A multivariate test and covariance analysis were used for the results evaluation.

The paper describes experimental validation of a laboratory flow apparatus used to measure the ignition delay times of diesel fuels at atmospheric pressure in near quiescent air. To validate the proposed method the experimental data were compared with the results from the studies performend on non-engine combustion chambers with continuous air flow at atmospheric pressure and various temperatures. The proposed flow apparatus, described in an earlier paper, has the means to provide air temperatures in the range between 650 and 730°C. An infrared radiation detector monitors the evolution of the temperature inside the combustion chamber. Ignition delay is measured as the time interval between the beginning of the needle lift and the beginning of increase in infrared radiation detected by the sensor. Six test fuels were used.

The flow of diesel fuel through multi-hole injection nozzles is well understood. There are, however, no comprehensive experimental results for the design of injection nozzles for alternate fuels. A steady state flow generator was designed and employed to analyze the effects of the physical fuel properties and the needle lift on the discharge coefficient for the nozzle orifice. Three fuels were tested: diesel reference fuel, a 50/50 mixture of diesel fuel and sunflower oil, and 100%. sunflower oil. The fuel viscosities range from 3.0 cS to 30.0 cS at 40°C. Five injection pressures ranging from 3.5 to 13.8 MPa, and eight increments of needle lift between 0.031 and 0.940 mm were used in this investigation. A significant influence of needle lift, injection nozzle pressure, and physical properties of fuels on the flow coefficient in the normal operating range of a typical diesel engine was proven.

The effect of increased clearance between the needle and its guides in a fuel injection nozzle on the rate of lacquer deposit formation from neat sunflower oil was investigated. Bosch fuel injection nozzles were tested on a fuel v injection calibration stand. The needle clearance reduction due to deposit buildup was monitored with a pneumatic leak test. Two test series of 100 hours duration each were performed at a temperature of 350°C. Each series consisted of ten 10-hour segments with a complete system shutdown after each segment. For the first test series the system was allowed to cool down before each shutdown. During the second test series the system was stopped while still hot. For fuels with physical and chemical properties similar to those of neat sunflower oil, excessive residue on the internal surfaces of the injection nozzles is likely to occur with the ultimate result of complete needle immobility.

The effect of temperature on the rate of lacquer deposit formation from neat sunflower oil on the needles of fuel injection nozzles was investigated. Boson fuel injection nozzles were tested on a fuel injection calibration stand. A pneumatic leak test was developed to monitor the needle clearance reduction due to deposit buildup. For fuels with physical and chemical properties similar to those of neat sunflower oil, excessive residue on the internal surfaces of the injection nozzles is likely to occur with the ultimate result of complete needle immobility. The rate of the lacquer buildup on the needle increases with temperature. Prior to final needle sticking, delay in start of injection, sluggish needle lift, increases in duration of injection, maximum, final residual, and maximum residual line pressures, and decrease in maximum needle lift can be observed. Based on the obtained results, the temperature of injection nozzles handling plant oil fuels should be kept as low as possible.

A 25-75 blend (v/v) of alkali-refined sunflower oil and diesel fuel, a 25-75 blend (v/v) of high oleic safflower oil and diesel fuel, a non-ionic sunflower oil-aqueous ethanol micro-emulsion, and a methyl ester of sunflower oil were evaluated as fuels in a direct injected, turbocharged, intercooled, 4-cylinder Allis-Chalmers diesel engine during a 200-hour ERA cycle laboratory screening endurance test. Engine performance on Phillips 2-D reference fuel served as baseline for the experimental fuels. This paper deals with several aspects of the anomalous behavior of the fuel injection system and its effects on long-term engine performance as experienced during the operation with the alternate fuels. Particular attention was paid to the changes in injection timing and the rates of injection pressure. Furthermore, secondary injection phenomena, initial and final stages of the fuel injection, which have been recognized as very frequent causes of abnormal combustion behavior, were analyzed.

An unmodified, direct-injected diesel engine was operated on diesel fuel and three blends of diesel fuel and sunflower oil. Heating of the fuels was used to change their viscosities. At normal fuel temperatures, specific fuel consumption and smoke emission increased for any power as sunflower oil content increased. Overall efficiency and exhaust temperature showed virtually no changes with fuel composition. Increasing fuel temperature caused a shift of best overall efficiency from high to low speeds, the magnitude of the shift depending on the plant oil concentration of the fuel. Thus fuel heating as a means of viscosity control may result in an efficiency penalty in the normal operating range of an engine. Typical plant oil induced engine contaminations such as wet stacking, excessive carbon accumulations, nozzle orifice blocking, and lubrication oil gelling were experienced.