Refine Your Search

Search Results

Standard

Rubber Boots for Drum-Type Hydraulic Brake Wheel Cylinders

2015-12-17
CURRENT
J1604_201512
This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of −40 to +120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).
Standard

Brake Master Cylinder Reservoir Diaphragm Gasket

2014-11-26
CURRENT
J1605_201411
This SAE Standard covers performance requirements and methods of test for master cylinder reservoir diaphragm gaskets that will provide a functional seal and protection from outside dirt and water.
Standard

Hydraulic Wheel Cylinders for Automotive Drum Brakes

2013-07-09
CURRENT
J101_201307
This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).
Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - Performance Requirements

2012-04-30
CURRENT
J1694_201204
This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.
Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - General Characteristics and Test Procedure

2012-04-30
CURRENT
J1693_201204
This SAE Recommended Practice specifies the general characteristics and test procedure to define the minimum characteristics, performance, and durability requirements. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The minimum characteristics, performance, and durability requirements are specified in SAE J1694.
Standard

Rubber Dust Boots for the Hydraulic Disk Brake Piston

2012-04-30
CURRENT
J1570_201204
This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of -40 to + 120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).
Standard

Hydraulic Master Cylinders for Motor Vehicle Brakes - Performance Requirements

2012-02-17
CURRENT
J1154_201202
This SAE Standard specifies minimum performance and durability requirements for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild). These performance requirements are based on those generally used by individual companies in the industry and have demonstrated satisfactory component field performance.
Standard

Hydraulic Master Cylinders for Motor Vehicle Brakes Test Procedure

2012-02-17
CURRENT
J1153_201202
This SAE Standard specifies the test procedure to determine minimum performance and durability characteristics for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild). The minimum performance and durability requirements are specified in SAE J1154.
Standard

Rubber Cups for Hydraulic Actuating Cylinders

2011-03-16
CURRENT
J1601_201103
These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document.
Standard

Rubber Seals for Hydraulic Disc Brake Cylinders

2008-05-13
HISTORICAL
J1603_200805
This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.
Standard

Hydraulic Wheel Cylinders for Automotive Drum Brakes

2006-08-16
HISTORICAL
J101_200608
This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).
Standard

Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders

2001-05-14
HISTORICAL
J1568_200105
The materials defined by this SAE Standard are glass-fiber-reinforced, mineral-filled phenolic molding compounds suitable for compression molding. Preforms may be radio frequency preheated or screw preheated slugs. Compound for use in hydraulic disc brake caliper pistons.
Standard

RUBBER BOOTS FOR DRUM-TYPE HYDRAULIC BRAKE WHEEL CYLINDERS

1995-01-01
HISTORICAL
J1604_199501
This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to +120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).
Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes-Performance Requirements

1994-06-26
HISTORICAL
J1694_199406
This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.
Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes-General Characteristics and Test Procedure

1994-06-01
HISTORICAL
J1693_199406
This SAE Recommended Practice specifies the general characteristics and test procedure to define the minimum characteristics, performance, and durability requirements. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The minimum characteristics, performance, and durability requirements are specified in SAE J1694.
Standard

Hydraulic Master Cylinders for Motor Vehicle Brakes-Performance Requirements

1991-06-01
HISTORICAL
J1154_199106
This SAE Standard specifies minimum performance and durability requirements for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild). These performance requirements are based on those generally used by individual companies in the industry and have demonstrated satisfactory component field performance.
Standard

Hydraulic Master Cylinders for Motor Vehicle Brakes-Test Procedure

1991-06-01
HISTORICAL
J1153_199106
This SAE Standard specifies the test procedure to determine minimum performance and durability characteristics for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild).
Standard

Hydraulic Wheel Cylinders for Automotive Drum Brakes

1989-12-01
HISTORICAL
J101_198912
This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).
Standard

Hydraulic Master Cylinders for Motor Vehicle Brakes-Performance Requirements

1977-04-01
HISTORICAL
J1154_197704
This SAE Standard specifies minimum performance and durability requirements for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild). These performance requirements are based on those generally used by individual companies in the industry and have demonstrated satisfactory component field performance.
Standard

Hydraulic Master Cylinders for Motor Vehicle Brakes Test Procedure

1976-07-01
HISTORICAL
J1153_197607
This SAE Standard specifies the test procedure to determine minimum performance and durability characteristics for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild).
X