Search Results

The modern solution of two-stage combustion, namely the Turbulent Jet Ignition, enables the combustion of ultra-lean mixtures. Thanks to this solution, it became possible to reduce fuel consumption and, at the same time, to increase the combustion process indicators (including the overall combustion system efficiency). The article presents the results of numerical tests of a heavy-duty engine equipped with the TJI system running on hydrogen fuel. The operating conditions of the Heavy-Duty engine at n = 1500 rpm and IMEP = 10 bar with a prechamber with 7 holes were analyzed. The research was conducted with the use of lean mixtures (global lambda ca. 2 or more). The AVL FIRE software was used to perform the analysis of different fuel doses delivered to the main chamber, with a constant global excess air coefficient value. Increasing the proportion of hydrogen in the pre-chamber resulted in its reduction in the main chamber.

Exhaust gas aftertreatment systems can, under certain conditions, create undesired chemical species as a result of their elimination reactions. A prime example of this is ammonia (NH3), which is not formed in the combustion reaction, but which can be formed within a three-way catalyst (TWC) when physicochemical conditions permit. The elimination of NOx in the TWC thus sometimes comes at the cost of significant emissions of NH3. Ammonia is a pollutant and a reactive nitrogen compound (RNC) and NH3 emissions should be analyzed in this context, alongside other RNC species. Examination of the literature on the subject published over the past two decades shows that ammonia, a species which is currently not subject to systematic emissions requirements for road vehicles in any market, is often identified as forming the majority of the RNC emissions under a range of operating conditions.

This paper discusses the legislative situation regarding type approval of plug-in hybrid vehicles (also known as off-vehicle charging hybrid-electric vehicles, OVC-HEV) in the range of exhaust emissions and fuel consumption. A range of tests were conducted on two Euro 6d-complaint OVC-HEVs to quantify emissions. Procedures were based on EU legislative requirements. For laboratory (chassis dyno) testing, two different test cycles and three different ambient temperatures were used for testing. Furthermore, in some cases additional measurements were performed, including measurement of emissions of particulate matter and continuous analysis of regulated and unregulated pollutants in undiluted exhaust. Consumption of electrical energy was also monitored. On-road testing was conducted on the test vehicle tested on the chassis dyno in the tests mentioned above, as well as on a second OVC-HEV test vehicle.

The article is an investigation into the exhaust emission impact of operating a shunting locomotive SM42 and a track diagnostics machine UPS-80-001. The comparison of the two vehicles makes it possible to estimate the overall environmental costs of two different types of rail vehicles operating at their typical work parameters. This was done using selected exhaust emission indicators. It is used to indicate the need for further improvement in vehicle ecology such as hybrid or electric systems. Other solutions are investigated as forms of mitigating the ecological impact of operating such vehicles in or near human population centers.

Non-Road machines constitutes a large group of machines designed for various tasks and mainly using CI engines for propulsion. This category includes vehicles with drive systems of a maximum capacity of several kilowatts as well as with drives with a capacity of up to thousands of kilowatts depending on the purpose of the machine. Within this group, mobile machines referred to as NRMM (Non-Road Mobile Machinery) stand out. Numerous studies of scientific institutions in Europe and around the world have proven the differences between the exhaust emissions tested in type approval tests and the actual emissions in this group of vehicles. They result from differences in operating points (crankshaft speed and load) of engines during their operation. A big problem is also their considerable age and degree of wear. Approval standards themselves are less stringent than those of heavy-duty vehicles (HDVs), although the engines have similar design and performance.

European Union RDE (real driving emissions) legislation requires that new vehicles be subjected to emissions tests on public roads. Performing emissions testing outside a laboratory setting immediately raises the question of the impact of ambient conditions - especially temperature - on the results. In the spirit of RDE legislation, a wide range of ambient temperatures are permissible, with mathematical moderation (correction) of the results only permissible for ambient temperatures <0°C and >+30°C. Within the standard range of temperatures (0°C to +30°C), no correction for temperature is applied to emissions results and the applicable emissions limits have to be met. Given the well-known link between the thermal state of an engine and its emissions following cold start, ambient temperature can be of great importance in determining whether a vehicle meets emissions requirements during an RDE test.

This paper discusses the importance of the inclusion of emissions from the cold start event during legislative on-road tests on passenger cars (RDE - real driving emissions tests conducted under real-world driving conditions, as defined by EU legislation). Results from a recently-registered gasoline-powered vehicle are presented, with the main focus on the comparison of exhaust emission results: excluding/including the cold start during the initial phase of the RDE test. Cold start is the most challenging aspect of emissions control for vehicles with spark ignition engines and the inclusion of the cold start event in RDE test procedure has wide-ranging implications both for the testing process and compliance with RDE legislation via optimisation of aftertreatment systems and the engine calibration. In addition to some theoretical arguments, the results of an RDE-compliant test performed using the aforementioned procedures are presented.

In this study, two vehicles were tested under real driving conditions with gaseous exhaust emissions measured using a portable emissions measurement system (PEMS). One of the vehicles featured a hybrid powertrain with a spark ignition internal combustion engine, while the other vehicle featured a non-hybrid (conventional) spark ignition internal combustion engine. Aside from differences in the powertrain, the two test vehicles were of very similar size, weight and aerodynamic profile, meaning that the power demand for a given driving trace was very similar for both vehicles. The test route covered urban conditions (but did include driving on a road with speed limit 90 km/h). The approximate test route distance was 12 km and the average speed was very close to 40 km/h.

This paper presents a study of passenger cars in terms of emissions measurements in tests conducted under real driving conditions (RDE - Real Driving Emissions) by means of PEMS (Portable Emission Measurement System) equipment. A special feature of the RDE tests presented in this paper is that they were performed under Polish conditions and the specified parameters may differ from those in most other European Union countries. Emission correction coefficients have been defined, based on the test results, equal to the increase (or decrease) of driving emissions during the laboratory (‘chassis dyno’) test or during normal usage in relation to the EU emission standards (emission class) of the vehicle.

The paper describes the measurement of PM emission from an excavator engine under actual operating conditions. The exploration of the relations between the engine operating parameters and its emissions requires measurements under actual conditions of engine operation. The specificity of the emission measurements, PM in particular, requires technologically advanced measuring devices. The situation gets even more complicated when, beside the PM mass. The particle size distribution and number (PN) also need to be measured. An important technical issue is the difficulty in fitting the measurement equipment in/on the vehicle in operation (e.g. excavator), which is why the presented investigations were carried out in a laboratory under simulated operation. The laboratory technicians applied load to the engines through the excavator hydraulic system.

The paper presents an analysis of the emission level from a heavy-duty truck of the GVW of 12,000 kg. The exhaust emission tests were performed under actual traffic conditions in the area of Poznań. For the tests portable exhaust emission analyzers SEMTECH DS and AVL Micro Soot Sensor were used. The characteristics of the exhaust emission components have been determined in relation to the engine speed and load as well as vehicle parameters (speed and acceleration). The paper includes an analysis of the engine operating conditions as well as the range of engine speeds and engine loads. The vehicle fuel consumption was also determined through the carbon balance method. Based on the obtained values of the emission of CO, NOx and PM, the emission indexes were determined that provided information on the relation of the measured emissions to the levels specified in the EEV standard. The emissions of all the exhaust components, except NOx were lower than the EEV limits.

The paper discusses the measurement of the PM emissions from non-road vehicles (a farm tractor and an excavator) under actual operating conditions. Full exploration of the relations between the operating parameters of these vehicles and their emissions requires measurements under actual conditions of their operation. The specificity of the emission measurements, PM in particular, requires technologically advanced measuring devices. The situation gets even more complicated if, beside the PM mass, we also wish to obtain the PM size distribution and particle number (PN). One of the more important technical issues is the difficulty in fitting of the measurement equipment in/on the vehicle in operation (e.g. a farm tractor). That is the reason why the investigations were carried out in a laboratory. The laboratory technicians applied load to the engines through external devices - a hydraulic system for the excavator and a brake coupled to the farm tractor power takeoff.

The paper presents the results of tests on a combustion engine of an armored modular vehicle 8x8 Rosomak under combat simulating conditions. For the measurements of the toxic compounds a portable SEMTECH DS analyzer by SENSORS was used. The analyzer allowed a measurement of toxic compounds at the same time measuring the mass flow rate of the exhaust gases. The analysis of the PM emission was performed based on the measurement of the size of the particulate matter (analyzer 3090 EEPS - Engine Exhaust Particle Sizer™ Spectrometer - by TSI Incorporated) and counting of the particles (analyzer Particle Counter by AVL). The measurements of CO, HC, NOx, PM and fuel consumption were performed under the conditions of combat simulation and in the overboost mode. Based on the obtained results, an analysis of the engine and vehicle operation was performed and the on-road and unit exhaust emissions as well as on-road and unit fuel consumption were compared.

The paper presents the results of the investigations of an armored modular vehicle 8x8 Rosomak fitted with a diesel engine during start and warm-up. For the measurements of the toxic compounds a portable SEMTECH DS analyzer by SENSORS was used. The analyzer allowed a measurement of exhaust emission at the same time measuring the mass flow rate of the exhaust gases. The analysis of the PM emission was performed based on the measurement of the size of the particulate matter (analyzer 3090 EEPS - Engine Exhaust Particle Sizer™ Spectrometer - by TSI Incorporated) and counting of the particles (analyzer Particle Counter by AVL). The measurements of CO, HC, NOx, PM and fuel consumption have also been carried out under static conditions, during startup and at constant engine speed without engine load. For the measurement of the engine operating conditions and the fuel consumption a diagnostic vehicle system was used.

The tests related to the exhaust emissions from non-road vehicles are currently performed on a chassis dynamometer under the name of NRSC (ISO 8178) and NRTC. In light of the growing requirements related to the environment protection in transport the authors recommend determining the exhaust emissions through real vehicle operating conditions. The tests carried out under real operating conditions could be used for the process of optimization of future power trains of regular road vehicles and non-road vehicles. What is more, these tests should be taken into account in the works on the changes of the legislation related to the emission limits from combustion engines. The paper presents the results of the tests on the exhaust emissions from an agricultural harvester engine and a tractor engine in real operating conditions. The harvester operation during the test consisted in crops collection from the field and the tractor operation during the test consisted in plowing.

The investigations into the emissions from light-duty vehicles are carried out on a chassis dynamometer in the NEDC test in Europe and FTP75 test in the US. Such tests do not entirely reflect the real road conditions. It should be noted that the changes in the methodology of emissions testing should go in the direction where they get closer to the actual road conditions. The paper presents the road test results obtained in an urban congested areas. The analysis of the road tests results (exhaust emissions and fuel consumption) was carried out considering the road conditions (vehicle speed and acceleration). The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. For these measurements a portable SEMTECH DS analyzer by SENSORS, Particle Counter by AVL and Particle Seizer EEPS by TSI has been used.

Due to a rapid development of air transportation there is a need for the assessment of real environmental risk related to the aircraft operation. The emission of carbon monoxide and particulate matter is still a serious threat~constituting an obstacle in the development of combustion engines. The applicable regulations related to the influence of the air transportation on the environment introduced by EPA (Environmental Protection Agency), ICAO (International Civil Aviation Organization) contained in JAR 34 (JAA, Joint Aviation Requirements, JAR 34, Aircraft Engine Emissions), FAR 34 (FAA, Federal Aviation Regulations, Part 34, Fuel Venting and Exhaust Emission Requirements for Turbine Engine Powered Airplanes), mostly pertain to the emission of noise and exhaust gas compounds, NOx in particular. They refer to jet engines and have stationary test procedures depending on the engine operating conditions.

In order to measure the concentration of exhaust emissions a mobile emission testing analyzer SEMTECH DS by SENSORS Inc was used. In the study the results of the vehicle emission tests in the road conditions were presented, as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle in motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of the emission intensity.

The investigations into the emissions from light-duty vehicles have been carried out on a chassis dynamometer (NEDC test in Europe and FTP75 test in the US). Such tests do not entirely reflect the real road conditions and that is why we should analyze the correlation of the laboratory versus on-road test results. The paper presents the on-road test results obtained in an urban and extra urban cycles. For these measurements a portable SEMTECH DS analyzer by SENSORS has been used. The device is an analyzer enabling an on-line measurement of the emission gases concentration in a real driving cycle under real road conditions. The road tests were performed on road portions of several kilometers each. The obtained results were compared with the results obtained for the same vehicle during the NEDC test on a chassis dynamometer. The comparative analysis was performed including the urban and extra-urban cycles.

In order to measure the concentration of exhaust a mobile analyzer SEMTECH DS by SENSORS Inc and particle matter by TSI was used. In the study the results of the vehicle emission tests in the road conditions were presented as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of emission intensity.