Search Results

Planning for charging in transport missions is vital when commercial long-haul vehicles are to be electrified. In this planning, accurate range prediction is essential so the trucks reach their destinations as planned. The rolling resistance significantly influences truck energy consumption, often considered a simple constant or a function of vehicle speed only. This is, however, a gross simplification, especially as the tire temperature has a significant impact. At 80 km/h, a cold tire can have three times higher rolling resistance than a warm tire. A temperature-dependent rolling resistance model is proposed. The model is based on thermal networks for the temperature at four places around the tire. The model is tuned and validated using rolling resistance, tire shoulder, and tire apex temperature measurements with a truck in a climate wind tunnel with ambient temperatures ranging from -30 to 25 °C at an 80 km/h constant speed.

Cylinder air-charge is one of the most important parts of the torque control in a gasoline engine, due to the necessity to keep a stoichiometric air-fuel ratio, for the three-way catalyst to work efficiently. Throttle and phasing of the camshafts are actuators that have a big effect on the cylinder air-charge, this results in a cross-coupling between the actuators. One approach to handle the cross-coupling that occurs with multiple actuators is to use model predictive control (MPC), that handles the cross-coupling through the use of models and optimization. Models that support computation of gradients and hessians are desirable for use in MPC. To support the model design experimental data of cylinder pressure, from an inline four-cylinder engine with dual independent cam phasing, supported by gas exchange simulation, the effects from variable valve timing on the cylinder air-charge are investigated during the valve overlap period.

Green zones are challenging problems for the thermal management systems of hybrid vehicles. This is because within the green zone the engine is turned off, and the only way to keep the aftertreatment system warm is lost. This means that there is a risk of leaving the green zone with a cold and ineffective aftertreatment system, resulting in high emissions. A thermal management strategy that heats the aftertreatment system prior to turning off the engine, in an optimal way, to reduce the NOx emissions when the engine is restarted, is developed. The strategy is also used to evaluate under what conditions pre-heating is a suitable strategy, by evaluating the performance in simulations using a model of a heavy-duty diesel powertrain and scenario designed for this purpose.

Exhaust aftertreatment systems are essential components in modern powertrains, needed to reach the low legislated levels of NOx and soot emissions. A well designed diesel engine exhaust aftertreatment system can have NOx conversion rates above 95%. However, to achieve high conversion the aftertreatment system must be warm. Because of this, large parts of the total NOx emissions come from cold starts where the engine has been turned off long enough for the aftertreatment system to cool down and loose its capacity to reduce NOx. It is therefore important to understand how the aftertreatment cools down when the engine in turned off. Experimental data for a catalyst cool-down process is presented and analyzed. The analysis shows that it is important to capture the spatial distribution of temperatures both in axial and radial directions. The data and analysis are used to design a catalyst thermal model that can be used for model based catalyst temperature monitoring and control.

When electrifying the powertrain, there arises an opportunity to revise the traditional turbocharging trade-off between fuel-economy and transient performance. With the help of electrification, it might be possible to make the trade-off in favor of fuel economy, since transient response can be improved by the electric machine. The paper investigates this trade-off by looking at three turbocharger selections. A conventionally dimensioned turbocharger, an efficiency optimized turbocharger with maintained flow capacity, and an efficiency optimized turbocharger with increased flow capacity. The concepts are evaluated on the following cases: stationary operation, engine tip-in performance, vehicle acceleration performance, and on road fuel economy performance. The investigation is based on a validated mean value engine model of a six cylinder inline CI engine, and on a validated driveline and vehicle model of a heavy-duty truck.

Downsizing and turbocharging with single or multiple stages has been one of the main solutions to decrease fuel consumption and harmful exhaust emissions, while keeping a sufficient power output. An accurate and reliable control-oriented compressor model can be very helpful during the development phase, as well as for engine calibration, control design, diagnostic purposes or observer design. A complete compressor model consisting of mass flow and efficiency models is developed and motivated. The proposed model is not only able to represent accurately the normal region measured in a compressor map but also it is capable to extrapolate to low compressor speeds. Moreover, the efficiency extrapolation is studied by analyzing the known problem with heat transfer from the hot turbine side, which introduces errors in the measurements done in standard gas stands.

Today’s need for fuel efficient vehicles, together with increasing engine component complexity, makes optimal control a valuable tool in the process of finding the most fuel efficient control strategies. To efficiently calculate the solution to optimal control problems a gradient based optimization technique is desirable, making continuously differentiable models preferable. Many existing control-oriented Diesel engine models do not fully posses this property, often due to signal saturations or discrete conditions. This paper offers a continuously differentiable, mean value engine model, of a heavy-duty diesel engine equipped with VGT and EGR, suitable for optimal control purposes. The model is developed from an existing, validated, engine model, but adapted to be continuously differentiable and therefore tailored for usage in an optimal control environment. The changes due to the conversion are quantified and presented.

1 Turbocharging plays an important role in the downsizing of engines. Model-based approaches for boost control are going to increasing the necessity for controlling the wastegate flow more accurately. In today’s cars, the wastegate is usually only controlled with a duty cycle and without position feedback. Due to nonlinearities and varying disturbances a duty cycle does not correspond to a certain position. Currently the most frequently used feedback controller strategy is to use the boost pressure as the controller reference. This means that there is a large time constant from actuation command to effect in boost pressure, which can impair dynamic performance. In this paper, the performance of an electrically controlled vacuum-actuated waste-gate, subsequently referred to as vacuum wastegate, is compared to an electrical servo-controlled wastegate, also referred to as electric wastegate.

1 In modern turbocharged engines the power output is strongly connected to the turbocharger speed, through the flow characteristics of the turbocharger. Turbo speed is therefore an important state for the engine operation, but it is usually not measured or controlled directly. Still the control system must ensure that the turbo speed does not exceed its maximum allowed value to prevent damaging the turbocharger. Having access to a turbo speed signal, preferably by a cheap and reliable estimation instead of a sensor, could be beneficial for over speed protection and supervision of the turbocharger. This paper proposes a turbo speed observer that only utilizes the conditions around the compressor and a model for the compressor map. These conditions are either measured or can be more easily estimated from available sensors compared the conditions on the turbine side.

The work extends a methodology, for searching for optimal heat release profiles, by adding complex constraints on states. To find the optimum heat release profile a methodology, that uses available theory and methods, was developed that enables the use of state of the art optimal control software to find the optimum combustion trace for a model. The methodology is here extended to include constraints and the method is then applied to study how sensitive the solution is to different effects such as heat transfer, crevice flow, maximum rate of pressure rise, maximum pressure, knock and NO generation. The Gatowski single zone model is extended to a pseudo two zone model, to get an unburned zone that is used to describe the knocking and a burned zone for NO generation. A modification of the extended Zeldovich mechanism that makes it continuously differentiable, is used for NO generation.

The combustion process has a high impact on the engine efficiency, and in the search for efficient engines it is of interest to study the combustion. Optimization and optimal control theory is used to compute the most efficient combustion profiles for single zone model with heat transfer and crevice effects. A model is first developed and tuned to experimental data, the model is a modification of the well known Gatowski et al.-model [1]. This model is selected since it gives a very good description of the in-cylinder pressure, and thus the produced work, and achieves this with a low computational complexity. This enables an efficient search method that can maximize the work to be developed. First, smooth combustion profiles are studied where the combustion is modeled using the Vibe function, and parametric optimization is used to search for the optimal profile.

In diesel engines with EGR and VGT, the gas flow dynamics has significant nonlinear effects. This is shown by analyzing DC-gains in different operating points showing that these gains have large variations. To handle these nonlinear effects, a nonlinear state dependent input transformation is investigated. This input transformation is achieved through inversion of the models for EGR-flow and turbine flow. It is shown that the input transformation handles the nonlinear effects and decreases the variations in DC-gains substantially. The input transformation is combined with a new control structure that has a pumping work minimization feature and consists of PID controllers and min/max-selectors for coordinated control of EGR-fraction and oxygen/fuel ratio. The EGR flow and the exhaust manifold pressure are chosen as feedback variables in this structure. Further, the set-points for EGR-fraction and oxygen/fuel ratio are transformed to set-points for the feedback variables.

In modern Diesel engines Exhaust Gas Recirculation (EGR) and Variable Geometry Turbochargers (VGT) have been introduced to meet the new emission requirements. A control structure that coordinates and handles emission limits and low fuel consumption has been developed. This controller has a set of PID controllers with parameters that need to be tuned. To be able to achieve good performance, an optimization based tuning method is developed and tested. In the optimization the control objectives are captured by a cost function. To aid the tuning a systematic method has been developed for selecting representative and significant transients that excite different modes in the controller. The performance is evaluated on the European Transient Cycle. It is demonstrated how weighting factors in the cost function influence control behavior, and that the proposed tuning method gives a significant improvement in control performance compared to standardized tuning methods for PID controllers.

Three methods for compression ratio estimation based on cylinder pressure traces are developed and evaluated for both motored and fired cycles. Two methods rely upon models of polytropic compression and expansion for the cylinder pressure. It is shown that they give a good estimate of the compression ratio, although the estimates are biased. A method based on a variable projection algorithm with a logarithmic norm of the cylinder pressure, which uses interpolation of polytropic models of the expansion and compression asymptotes, is recommended when computational time is an important issue. For motored cycles it yields the smallest bias and confidence intervals for these two methods. For firing cycles a user-specified weighting factor is needed during the combustion phase, which pays off in a smaller estimation bias but also a higher variance. The third method includes heat transfer, crevice effects, and a commonly used heat release model for firing cycles.

It is important to determine the phasing of a measured cylinder pressure trace and crank angle with high accuracy. The reason is that erroneous determination of the position of TDC is a major error source when calculating properties such as heat release etc. A common way to determine the TDC position is to study motored cycles. Heat transfer makes the task more complicated, since it shifts the position of the maximum pressure away from TDC. In this paper a new method for determining the TDC position is proposed that does not require any additional sensors other than a cylinder pressure sensor and an incremental encoder. The idea is to find a point that the cylinder pressure from a motored cycle is symmetric around, since the volume is close to symmetric on either side of TDC. The new method and four published methods are tested and evaluated. Cylinder pressure data used for comparison are from simulations of a SAAB Variable Compression engine.

A program package, that calculates chemical equilibrium and thermodynamic properties of reactants and products of a combustion reaction between fuel and air, has been developed and validated. The package consists of the following four parts: 1) A program for calculating chemical equilibrium. 2) A database that contains thermochemical information about the molecules, which comes from the GRI-Mech tables. 3) A GUI that allows the user to easily select fuels, fuel/air ratio for the reaction, and combustion products. 4) A set of functions designed to access the thermochemical database and the chemical equilibrium programs. Results are validated against both the NASA equilibrium program (Gordon and McBride, 1994) and the program developed by Olikara and Borman (1975). It is shown that the new method gives results identical to those well recognized Fortran programs.

Mean value cylinder air charge (CAC) estimation models for control and diagnosis are investigated on turbocharged SI-engines. Two topics are studied; Firstly CAC changes due to fuel enrichment and secondly CAC sensitivity to exhaust manifold pressure changes. The objective is to find a CAC model suitable for control and diagnosis. Measurements show that CAC models based on volumetric efficiency gives up to 10% error during fuel enrichment. The error is caused by the cooling effect that the fuel has as it evaporates and thus increases the charge density. To better describe the CAC during fuel enrichment a simple one parameter model is proposed which reduces the CAC estimation error on experimental data from 10% to 3%. With active wastegate control, the pressure changes in the exhaust manifold influences the CAC. The magnitude of this influence is investigated using sensitivity analysis on an exhaust manifold pressure dependent CAC-model.

Exhaust temperatures are important for turbine and catalyst performance. A set of exhaust temperature models suitable for turbo matching as well as design and analysis of engine control systems are developed and investigated. The models are lumped parameter heat transfer models, that fall within the category of mean value engine models. The model is developed for describing exit temperatures from the exhaust manifold and temperature drops in pipe sections in the exhaust system. The components used to model the exhaust temperature are: engine out temperature, temperature drop in a straight pipe, and a set of heat transfer modes. The model is validated using data from three different engines. It is shown that, for a spark ignited engine operating at MBT and stoichiometric conditions, it is sufficient to model the engine out temperature as a linear function of mass flow. Recommendations for tuning the model are also given.

Emissions from modern SI-engines are reduced by a three way catalyst. However if there are leaks in the exhaust system before the catalyst emissions increase for two reasons. First the untreated emissions leak out. Second which is worse, due to waves in the exhaust system, oxygen leaks into the manifold and causes an oxygen sensor offset. The result is increased emissions as the air/fuel controller makes the engine run rich. Here a method to detect leakages in the exhaust manifold is presented. The sensors used are binary oxygen sensor(s), intake manifold pressure and temperature, and the air mass flow sensor. Injection time is also used to estimate air/fuel ratio. Experimental results are shown with measurements from a turbo charged SAAB SI production engine with wastegate.

Three methods for estimating the compression from measured cylinder pressure traces are described and evaluated for both motored and fired cycles against simulated and measured cylinder pressure. The first two rely upon a model of polytropic compression, and it is shown that they give a good estimate of the compression ratio for simulated cycles for low compression ratios. For high compression ratios, these simple models lack the information about heat transfer. The third method includes a standard heat transfer and crevice effect model, together with a heat release model and is able to estimate the compression ratio more accurately.