Refine Your Search

Topic

Search Results

Standard

Nomenclature - Hydraulic Backhoes

2019-10-09
WIP
J326
This SAE standard includes hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors. Illustrations used are not intended to include all existing commercial machines or to be exact descriptions of any particular machine. The illustrations have been chosen to describe the principles to be used in applying this standard.
Standard

Cutting Edge - Double Bevel Cross Sections

2019-04-22
WIP
J738
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a. Scrapers as defined in ISO 7133. b. Dozers as described in ISO 6747. c. Loaders as described in ISO 7131. d. Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.
Standard

Cutting Edge - Double Bevel Cross Sections

2014-01-08
CURRENT
J738_201401
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.
Standard

Rated Operating Load for Loaders

2013-01-02
CURRENT
J818_201301
This SAE Standard establishes the definition of a normal all day rated operating load for loaders as defined in SAE J1057. This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

2011-12-08
CURRENT
J743_201112
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Nomenclature - Rollers and Compactors

2011-10-27
CURRENT
J1017_201110
This SAE Standard provides names of major components peculiar to rollers and compactors. Illustrations of components are not intended to be exactly descriptive of any particular machine. NOTE: Rollers and compactors will be defined in a section added to SAE J1057a.
Standard

Rated Operating Load for Loaders Equipped with Log or Material Forks Without Vertical Mast

2011-10-27
CURRENT
J1197_201110
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.
Standard

Countersunk Square Holes for Cutting Edges and End Bits

2011-10-25
CURRENT
J740_201110
To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further defined in SAE J737, J739 and J1304. End bits are further defined in SAE J63. 1 When section thickness exceeds A in drawing 1 (Figure 2) (countersunk one side) or B in drawing 4 (countersunk both sides), use counterbore with diameter D, as shown in cross section drawings 2, 5 and 6, or extended countersink C, as shown in cross section drawings 3 and 7. 2 The inscribed circle of the square holes shall be concentric with countersink or counterbore within 0.03 in (0.8 mm).
Standard

Cutting Edge - Cross Sections Loader Straight with Bolt Holes

2011-10-25
CURRENT
J1304_201110
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters. NOTE—For some heavy-duty applications, cross sections with larger blunts, greater bevel angles, and larger bolt holes may be required.
Standard

Earthmoving Machinery-Coupling of Attachments to Skid Steer Loaders

2008-05-01
CURRENT
J2513_200805
This SAE Standard sets forth standard dimension requirements for the loader attachment bracket and attachment interface to allow interchangeability of attachments on skid steer loaders whose operating mass (see SAE J/ISO 6165) is 4,500 kg or less. Narrow skid steer loaders may have a width that does not allow compliance with this standard. The design of the loader attachment bracket locking system is not restricted by this standard and is left to the discretion of the manufacturer. The purpose of this document is to provide dimensions to standardize the coupling interface between skid steer loaders and their attachments that are manufactured worldwide.
Standard

Loading Ability Test Procedure--Scrapers

2006-02-05
HISTORICAL
J764_200602
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport materials. The purpose of the scraper loading ability test is to determine the amounts of specified material that can be loaded with specified times and to express the data as a load-growth curve. The amount loaded is measured in kilograms and should be converted to volume by means of unit mass for reporting purposes.
Standard

Machine Slope Operation Test Code

2003-05-12
CURRENT
J897_200305
This SAE Standard applies to off-road self-propelled construction, forestry and industrial machines as listed in categories 1, 2, and 4 of SAE J1116. Purpose This Standard provides a field procedure to determine the ability of a machine to operate statically and dynamically on sloping surfaces. Depending upon the objective of the test, any item listed as specified is to be selected at the discretion of either the manufacturer, the test agency, the owner, or a combination of these parties.
Standard

Capacity Rating--Dumper Body and Trailer Body

2003-05-08
CURRENT
J1363_200305
This SAE Standard applies to dumper bodies as defined in SAE J1016 and dumper trailers as defined in SAE J734. It is similar to ISO 6483. Purpose The purpose of this document is to provide a uniform method for calculating the SAE rated volumetric capacity.
Standard

Nomenclature--Crawler Tractor

2002-02-21
CURRENT
J727_200202
This Standard provides provides names of major components peculiar to crawler tractors as defined in SAE J1057a (June, 1975). Illustrations of components are not intended to be exactly descriptive of any particular machine.
X