Refine Your Search

Search Results

Standard

Cutting Edge - Double Bevel Cross Sections

2019-04-22
WIP
J738
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a. Scrapers as defined in ISO 7133. b. Dozers as described in ISO 6747. c. Loaders as described in ISO 7131. d. Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.
Standard

Cutting Edge - Double Bevel Cross Sections

2014-01-08
CURRENT
J738_201401
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.
Standard

Rated Operating Load for Loaders

2013-01-02
CURRENT
J818_201301
This SAE Standard establishes the definition of a normal all day rated operating load for loaders as defined in SAE J1057. This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

2011-12-08
CURRENT
J743_201112
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Nomenclature - Rollers and Compactors

2011-10-27
CURRENT
J1017_201110
This SAE Standard provides names of major components peculiar to rollers and compactors. Illustrations of components are not intended to be exactly descriptive of any particular machine. NOTE: Rollers and compactors will be defined in a section added to SAE J1057a.
Standard

Countersunk Square Holes for Cutting Edges and End Bits

2011-10-25
CURRENT
J740_201110
To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further defined in SAE J737, J739 and J1304. End bits are further defined in SAE J63. 1 When section thickness exceeds A in drawing 1 (Figure 2) (countersunk one side) or B in drawing 4 (countersunk both sides), use counterbore with diameter D, as shown in cross section drawings 2, 5 and 6, or extended countersink C, as shown in cross section drawings 3 and 7. 2 The inscribed circle of the square holes shall be concentric with countersink or counterbore within 0.03 in (0.8 mm).
Standard

Cutting Edge - Cross Sections Loader Straight

2011-10-25
CURRENT
J1303_201110
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85. NOTE—For some heavy duty applications, cross sections with larger blunts and greater bevel angles may be required.
Standard

Cutting Edge - Optional Cross-Sections and Dimensions Loader Straight

2011-10-25
CURRENT
J1581_201110
The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adaptors on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.
Standard

Earthmoving Machinery-Coupling of Attachments to Skid Steer Loaders

2008-05-01
CURRENT
J2513_200805
This SAE Standard sets forth standard dimension requirements for the loader attachment bracket and attachment interface to allow interchangeability of attachments on skid steer loaders whose operating mass (see SAE J/ISO 6165) is 4,500 kg or less. Narrow skid steer loaders may have a width that does not allow compliance with this standard. The design of the loader attachment bracket locking system is not restricted by this standard and is left to the discretion of the manufacturer. The purpose of this document is to provide dimensions to standardize the coupling interface between skid steer loaders and their attachments that are manufactured worldwide.
Standard

Loading Ability Test Procedure--Scrapers

2006-02-05
HISTORICAL
J764_200602
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport materials. The purpose of the scraper loading ability test is to determine the amounts of specified material that can be loaded with specified times and to express the data as a load-growth curve. The amount loaded is measured in kilograms and should be converted to volume by means of unit mass for reporting purposes.
Standard

Machine Slope Operation Test Code

2003-05-12
CURRENT
J897_200305
This SAE Standard applies to off-road self-propelled construction, forestry and industrial machines as listed in categories 1, 2, and 4 of SAE J1116. Purpose This Standard provides a field procedure to determine the ability of a machine to operate statically and dynamically on sloping surfaces. Depending upon the objective of the test, any item listed as specified is to be selected at the discretion of either the manufacturer, the test agency, the owner, or a combination of these parties.
Standard

Capacity Rating--Dumper Body and Trailer Body

2003-05-08
CURRENT
J1363_200305
This SAE Standard applies to dumper bodies as defined in SAE J1016 and dumper trailers as defined in SAE J734. It is similar to ISO 6483. Purpose The purpose of this document is to provide a uniform method for calculating the SAE rated volumetric capacity.
Standard

Nomenclature--Crawler Tractor

2002-02-21
CURRENT
J727_200202
This Standard provides provides names of major components peculiar to crawler tractors as defined in SAE J1057a (June, 1975). Illustrations of components are not intended to be exactly descriptive of any particular machine.
Standard

Drawbars--Crawler Tractor

2002-02-21
CURRENT
J749_200202
This SAE Standard provides recommended dimensions for drawbars for crawler tractors as defined in SAE J1057 (SEP88). It includes only those dimensions which will affect the attaching of towed equipment.
Standard

Component Nomenclature--Scrapers

2000-06-28
CURRENT
J728_200006
This SAE Standard provides names of major components peculiar to the scraper portion of tractor-scrapers. Reference SAE J1057. Illustrations of components are not intended to be exactly descriptive of any particular machine.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

2000-06-01
HISTORICAL
J743_200006
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Hole Placement on Dozer End Bits

1998-05-01
CURRENT
J63_199806
The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057a up to a maximum weight of 100,000 lb (45,000 kg).
Standard

Capacity Rating-Dumper Body and Trailer Body

1995-11-01
HISTORICAL
J1363_199511
This SAE Standard applies to dumper bodies as defined in SAE J1016 and dumper trailers as defined in SAE J734. It is similar to ISO 6483. The purpose of this standard is to provide a uniform method for calculating the SAE rated volumetric capacity.
X